AUTOMATIC TRANSAXLE SYSTEM (for Hatchback) > DETAILS



FUNCTION OF MAIN COMPONENTS
  1. The main components of the U340E automatic transaxle system are as follows:

    Component
    Function
    Forward Clutch (C1)
    Connects the input shaft and front planetary sun gear.
    Direct Clutch (C2)
    Connects the intermediate shaft and rear planetary carrier.
    Reverse Clutch (C3)
    Connects the intermediate shaft and rear planetary sun gear.
    OD and 2nd Brake (B1)
    Locks the rear planetary sun gear.
    2nd Brake (B2)
    Prevents the rear planetary sun gear from turning counterclockwise.
    1st and Reverse Brake (B3)
    Locks the front planetary ring gear and rear planetary carrier.
    No. 1 1-way Clutch (F1)
    Prevents the rear planetary sun gear from turning counterclockwise.
    No. 2 1-way Clutch (F2)
    Prevents the front planetary ring gear and rear planetary carrier from turning counterclockwise.
    Planetary Gears
    Change the route through which driving force is transmitted, in accordance with the operation of both clutch and brake, in order to increase or reduce the input and output speed.
    Shift Solenoid Valve S1
    1. Switches the 2-3 shift valve.
    2. Controls the C2 clutch.
    Shift Solenoid Valve S2
    1. Switches the 1-2 and 3-4 shift valves.
    2. Controls the C1 clutch and 2 brakes (B1 and B2).
    Shift Solenoid Valve ST
    1. Switches the 3-4 shift timing valve.
    2. Switches the No. 1 4-3 shift timing valve.
    Shift Solenoid Valve SLU
    Controls the lock-up clutch.
    Shift Solenoid Valve SLT
    1. Controls the line pressure.
    2. Controls the secondary pressure.
    3. Controls the accumulator backpressure.
    ATF Temperature Sensor (Transmission Wire)
    Detects the ATF temperature.
    Speed Sensor NT (Transmission Revolution Sensor)
    Detects the input speed of the transaxle.
    Park/Neutral Position Switch Assembly
    Detects the shift lever position.
    Transmission Control Switch
    Detects the shift lever in 3 position.
    Shift Lock Control ECU
    Controls the shift lock system.
    Stop Light Switch Assembly
    Detects the brake pedal depressed.
    Combination Meter Assembly
    Detects the vehicle speed signal.
    MIL
    Illuminates or blinks to inform the driver when the ECM detects a malfunction.
    Shift Position Indicator
    Indicates the shift lever position.
    ECM
    1. Controls each shift solenoid valve and engine output in response to a signal from each sensor and switch.
    2. When the ECM detects a malfunction, it makes a diagnosis and memorizes the failed section.


SYSTEM CONTROL
  1. Automatic Transaxle Controls List

    Control
    Outline
    Clutch to Clutch Pressure Control
    Controls the pressure that is applied directly to B1 brake and C1 clutch by actuating the shift solenoid valves (ST, SLT) in accordance with the ECM signals.
    Clutch Pressure Control
    The shift solenoid valve SLT minutely controls the clutch pressure in accordance with the engine output and driving conditions.
    Line Pressure Control
    Actuates the shift solenoid valve SLT to control the line pressure in accordance with information from the ECM and the operating conditions of the transaxle.
    Shift Control in Uphill/Downhill Traveling
    Controls to restrict the 4th upshift or to provide appropriate engine braking by using the ECM to determine whether the vehicle is traveling on uphill or downhill.
    Shift Timing Control
    The ECM sends current to the shift solenoid valve S1 and/or S2 based on signals from each sensor and shifts the gear.
    Flex Lock-up Clutch Control
    Controls the shift solenoid valve SLU, provides an intermediate mode between the on/off operation of the lock-up clutch, and increases the operating range of the lock-up clutch to ensure fuel economy.
    Lock-up Timing Control
    The ECM sends current to the shift solenoid valve SLU based on the signals from each sensor and engages or disengages the lock-up clutch.
    Engine Torque Control
    Temporarily retards the engine ignition timing to restrict the output torque, thus ensuring the shift feel during up or down shifting.
    "N" to "D" Squat Control
    When the shift lever is shifted from the "N" to "D" position, the gear is temporarily shifted to the 3rd and then to the 1st to reduce vehicle squat.
    Shift Lock System
    The shift lock mechanism prevents the shift lever from being moved to any position other than P, unless the ignition switch is ON and the brake pedal is depressed.
    Fail-safe
    Even if a malfunction is detected in the sensors or solenoids, the ECM effects fail-safe control to prevent the vehicle's drivability from being affected significantly.
    Diagnosis
    When the ECM detects a malfunction, the ECM makes a diagnosis and memorizes the failed section.



  2. Clutch to Clutch Pressure Control

    1. This control is used for shifting from 3rd to 4th gear, and from 4th to 3rd gear. It actuates shift solenoid valves ST and SLT in accordance with the signals from the ECM, and guides this output pressure directly to the No. 1 4-3 shift timing valve and the 3-4 shift timing valve in order to regulate the line pressure that acts on the B1 brake (OD and 2nd brake) and C1 clutch (forward clutch).



    2. As a result, compact B1 and C1 accumulators without a backpressure chamber have been realized.


      X106284E03



  3. Clutch Pressure Control



    1. The ECM monitors the signals from various types of sensor such as the speed sensor NT (transmission revolution sensor), allowing shift solenoid valve SLT to minutely control the clutch pressure in accordance with engine output and driving conditions. As a result, smooth shift characteristics have been realized.


      X106285E02



  4. Line Pressure Control

    1. Through the use of the shift solenoid valve SLT, the line pressure is appropriately controlled in accordance with the engine torque information, as well as with the internal operating conditions of the torque converter assembly and the transaxle.



    2. Accordingly, the line pressure can be controlled minutely in accordance with the engine output, traveling condition and the ATF temperature, thus realizing smooth shift characteristics and regulating the workload in the oil pump.


      X106363E03



  5. Shift Control in Uphill/Downhill Traveling

    1. This control helps minimize the gear shifting when the driver operates the accelerator pedal while driving on a winding uphill or downhill road in order to ensure a smooth drive.

    2. When the ECM detects uphill travel, it prohibits upshifting to 4th after downshifting to 3rd.



    3. If a signal indicating that the driver has operated the brake pedal is input while the ECM detects downhill travel, it downshifts from 4th to 3rd.


      X106323E01



    4. The actual acceleration calculated from the speed sensor signal is compared with the reference acceleration (based on level road travel) stored in the ECM to determine uphill or downhill travel.


      X104263E01


      Text in Illustration (Uphill:) 
      *a
      Smaller
      -
      -
      V100135
      Reference Acceleration
      V100136
      Actual Acceleration

      X104264E01


      Text in Illustration (Downhill:) 
      *a
      Greater
      -
      -
      V100135
      Reference Acceleration
      V100136
      Actual Acceleration



  6. Flex Lock-up Clutch Control

    1. In addition to the conventional lock-up timing control, flex lock-up clutch control is used.

    2. This flex lock-up clutch control regulates the solenoid valve SLU as an intermediate mode between the on/off operation of the lock-up clutch.



    3. The flex lock-up clutch control operates during acceleration, in the 3rd and 4th gears in the D position, and during deceleration, in the 3rd and 4th gears in the D position and in the 3rd gear in the 3 position.


      X106283E03


      X102147E08


      Flex Lock-up Operation 
      Shift Lever Position
      Gear
      Acceleration Flex Lock-up
      Deceleration Flex Lock-up
      D
      1st
      X
      X
      2nd
      X
      X
      3rd
      ○
      ○
      4th
      ○
      ○
      3
      1st
      X
      X
      2nd
      X
      X
      3rd
      X
      ○

      HINT:
      ○: Operate
      X: Does not operate



  7. Shift Lock System

    1. The key interlock device prevents the key from being pulled out after the ignition switch is turned OFF, unless the shift lever is moved to the P position. Thus, the driver is urged to park the vehicle in the P position.

    2. The shift lock mechanism prevents the shift lever from being shifted to a position other than the P position, unless the ignition switch is ON and the brake pedal is depressed. It prevents the vehicle from starting off suddenly.



    3. The shift lock control ECU uses the P detection switch to detect the shift lever position, and receives input signals from the stop light switch assembly and ignition switch. Upon receiving these signals, the shift lock control ECU turns on the key interlock solenoid and the shift lock solenoid in order to release the key interlock and shift lock.


      X106305E04


CONSTRUCTION


  1. Torque Converter Assembly

    1. The torque converter assembly has appropriately designed fluid passages and impeller configuration, resulting in substantially enhanced transmission efficiency to ensure good starting, acceleration and fuel economy.



    2. Furthermore, a hydraulically operated lock-up mechanism which cuts power transmission losses due to slippage at medium and high speeds is used.


      X106290E01


      Text in Illustration 
      *1
      Pump Impeller
      *2
      1-way Clutch
      *3
      Stator
      *4
      Turbine Runner
      *5
      Lock-up Clutch
      -
      -



  2. Oil Pump



    1. The oil pump is combined with torque converter assembly, lubricates the planetary gear units and supplies operating pressure to the hydraulic control.


      X106306E01


      Text in Illustration 
      *1
      Front Oil Pump Body
      *2
      Front Oil Pump Driven Gear
      *3
      Front Oil Pump Drive Gear
      *4
      Stator Shaft Assembly



  3. Planetary Gear Unit

    1. A CR-CR type planetary gear is used in the planetary gear unit, which is located on the input shaft. In this planetary gear unit, the front planetary carrier is joined to the rear ring gear, and the rear planetary carrier is joined to the front ring gear. As a result, the unit has been made significantly simpler and compact.



    2. A centrifugal fluid pressure canceling mechanism is used in the C1 clutch, which is applied when downshifting from 4th.


      X106291E01


      Text in Illustration 
      *1
      Counter Drive Gear
      *2
      Input Shaft
      *3
      Rear Planetary Gear Assembly
      *4
      Front Planetary Gear Assembly
      *5
      Counter Driven Gear
      -
      -

    3. The functions of the clutches and brakes are as follows:

      Component
      Function
      C1
      Forward Clutch
      Connects the input shaft and front planetary sun gear.
      C2
      Direct Clutch
      Connects the intermediate shaft and rear planetary carrier.
      C3
      Reverse Clutch
      Connects the intermediate shaft and rear planetary sun gear.
      B1
      OD and 2nd Brake
      Locks the rear planetary sun gear.
      B2
      2nd Brake
      Prevents the rear planetary sun gear from turning counterclockwise.
      B3
      1st and Reverse Brake
      Locks the front planetary ring gear and rear planetary carrier.
      F1
      No. 1 1-way Clutch
      Prevents the rear planetary sun gear from turning counterclockwise.
      F2
      No. 2 1-way Clutch
      Prevents the front planetary ring gear and rear planetary carrier from turning counterclockwise.
      Planetary Gears
      These gears change the route through which driving force is transmitted, in accordance with the operation of both clutch and brake, in order to increase or reduce the input and output speed.



  4. Centrifugal Fluid Pressure Canceling Mechanism

    1. During shifting, in addition to the fluid pressure controlled by the valve body, the fluid pressure generated by centrifugal force (centrifugal fluid pressure) in chamber A also acts on the piston, and causes an increase in shifting shock generated by revolution differences between the input and output parts of the clutch by speeding the clutch engagement.



    2. In order to improve the shifting characteristics for 4-3 and 3-4 shifting for which high responsiveness is required, a centrifugal fluid pressure canceling mechanism is applied.


      X106292E01


      Text in Illustration 
      *1
      C1 Clutch
      *2
      Chamber A
      *3
      Chamber B
      *4
      Piston



    3. The canceling fluid pressure canceling mechanism is a chamber (chamber B) located opposite to chamber A. By filling chamber B with shaft lubrication fluid, an equal amount of centrifugal fluid pressure is generated there and works against the centrifugal fluid pressure in chamber A.


      X100592E03



  5. Transmission Valve Body Assembly



    1. The valve body consists of the upper and lower valve bodies and 5 shift solenoid valves.


      X106360E01


      Text in Illustration 
      *1
      Shift Solenoid Valve SLU
      *2
      Shift Solenoid Valve S2
      *3
      Shift Solenoid Valve S1
      *4
      Shift Solenoid Valve ST
      *5
      Shift Solenoid Valve SLT
      *6
      Lower Valve Body
      *7
      Upper Valve Body
      -
      -

      X106294E01


      Text in Illustration (Upper Valve Body:) 
      *1
      Lock-up Relay Valve
      *2
      Secondary Regulator Valve
      *3
      3-4 Shift Timing Valve
      *4
      Low Coast Modulator Valve
      *5
      No. 1 4-3 Shift Timing Valve
      *6
      2-3 Shift Valve
      *7
      Coast Relay Valve
      *8
      Solenoid Relay Valve
      *9
      Reverse Control Valve
      -
      -

      X106295E01


      Text in Illustration (Lower Valve Body:) 
      *1
      No. 2 4-3 Shift Timing Valve
      *2
      3-4 Shift Valve
      *3
      Primary Regulator Valve
      *4
      1-2 Shift Valve
      *5
      Accumulator Control Valve
      *6
      Pressure Relief Valve



  6. Shift Solenoid Valve SLT

    1. In order to supply hydraulic pressure proportional to the current that flows to the solenoid coil, shift solenoid valve SLT is provided.



    2. The valve linearly controls the line pressure, secondary pressure and accumulator backpressure based on the signals from the ECM.


      X105785E01


      Function of Shift Solenoid Valve SLT 
      Shift Solenoid Valve
      Function
      SLT
      1. Line pressure control
      2. Secondary pressure control
      3. Accumulator backpressure control



  7. Shift Solenoid Valve SLU

    1. In order to supply hydraulic pressure proportional to the current that flows to the solenoid coil, shift solenoid valve SLU is provided.



    2. The valve linearly controls the lock-up clutch pressure based on the signals from the ECM.


      X105786E01


      Function of Shift Solenoid Valve SLU 
      Shift Solenoid Valve
      Function
      SLU
      Lock-up clutch pressure control



  8. Shift Solenoid Valve S1 and S2



    1. These shift solenoid valves use a 3-way solenoid valve.


      X105787E01


      Text in Illustration 
      *a
      Off Condition
      *b
      On Condition
      V100135
      Control Pressure
      V100136
      Drain
      V100137
      Line Pressure
      V100138
      Cylinder Ball Moving Direction

      Function of Shift Solenoid Valve S1 and S2 
      Shift Solenoid Valve
      Function
      S1
      1. 2-3 shift valve switching
      2. C2 clutch control
      S2
      1. 1-2 and 3-4 shift valves switching
      2. C1 clutch and 2-brake (B1 and B2) control



  9. Shift Solenoid Valves ST



    1. This shift solenoid valve use a 3-way solenoid valve.


      X105788E01


      Text in Illustration 
      *a
      Off Condition
      *b
      On Condition
      V100135
      Control Pressure
      V100136
      Drain
      V100137
      Line Pressure
      V100138
      Cylinder Ball Moving Direction

      Function of Shift Solenoid Valve ST 
      Shift Solenoid Valve
      Function
      ST
      1. 3-4 shift timing valves switching
      2. No. 1 4-3 shift valves switching



  10. ATF Temperature Sensor (Transmission Wire)

    1. The ATF temperature sensor (transmission wire) is installed in the lower valve body for direct detection of the fluid temperature.



    2. The ATF temperature sensor (transmission wire) is used for the correction of clutch and brake pressures to give smooth shift quality every time.


      X106296E01


      Text in Illustration 
      *1
      Lower Valve Body
      *2
      ATF Temperature Sensor (Transmission Wire)



  11. Speed Sensor NT (Transmission Revolution Sensor)



    1. The speed sensor NT (transmission revolution sensor) detects the input speed of the transaxle. The forward clutch (C1) drum is used as the timing rotor for this sensor. Thus, the ECM can detect shift timing of the gears and appropriately control the engine torque and hydraulic pressure in response to the various conditions.


      X106347E01


      Text in Illustration 
      *1
      Speed Sensor NT (Transmission Revolution Sensor)
      -
      -



  12. Shift Control Mechanism

    1. A gate type shift lever that uses a transmission control cable is used.



    2. The shift control mechanism consists of a shift lock control unit assembly and a transmission control cable assembly.


      X106344E01


      Text in Illustration 
      *1
      Transmission Control Cable Assembly
      *2
      Shift Lock Control Unit Assembly
      *a
      Shift Pattern
      -
      -



  13. Park/Neutral Position Switch Assembly and Transmission Control Switch

    1. The park/neutral position switch assembly sends the P, R, N, D, 2 and L position signals to the ECM.

    2. The transmission control switch sends the 3 position signal to the ECM.

    3. The ECM controls the automatic transaxle system in accordance with the shift lever position signals.



    4. The ECM transmits signals to the combination meter assembly for the shift position indicator (P, R, N, D, 2, 3 and L) in response to the signals received from the switches.


      X105779E03



  14. Automatic Transmission Fluid (ATF) WS



    1. TOYOTA genuine ATF WS is used to reduce the resistance of the ATF and ensure fuel economy by reducing its viscosity in the practical operation range. At the high-temperatures, the viscosity is the same as that of TOYOTA genuine ATF Type T-IV, which ensures the durability of the automatic transmission.


      X100046E01


OPERATION


  1. Transmission Power Flow

    Shift Lever Position
    Gear
    Solenoid Valve
    Clutch
    Brake
    1-way Clutch
    S1
    S2
    C1
    C2
    C3
    B1
    B2
    B3
    F1
    F2
    P
    Park
    On
    On
    -
    -
    -
    -
    -
    -
    -
    -
    R
    Reverse
    On
    On
    -
    -
    ○
    -
    -
    ○
    -
    -
    N
    Neutral
    On
    On
    -
    -
    -
    -
    -
    -
    -
    -
    D
    1st
    On
    On
    ○
    -
    -
    -
    -
    -
    -
    ○
    2nd
    On
    Off
    ○
    -
    -
    -
    ○
    -
    ○
    -
    3rd
    Off
    Off
    ○
    ○
    -
    -
    ○
    -
    -
    -
    4th
    Off
    On
    -
    ○
    -
    ○
    ○
    -
    -
    -
    3
    1st
    On
    On
    ○
    -
    -
    -
    -
    -
    -
    ○
    2nd
    On
    Off
    ○
    -
    -
    -
    ○
    -
    ○
    -
    3rd
    Off
    Off
    ○
    ○
    -
    -
    ○
    -
    -
    -
    2
    1st
    On
    On
    ○
    -
    -
    -
    -
    -
    -
    ○
    2nd
    On
    Off
    ○
    -
    -
    ○
    ○
    -
    ○
    -
    L
    1st
    On
    On
    ○
    -
    -
    -
    -
    ○
    -
    ○

    HINT:
    ○: Operation
    -: Not operation


    X106298E01


    X106299E01


    X106300E01


    X106301E01


    X106302E01


    X106303E01


    X106304E01


FAIL-SAFE
  1. The fail-safe function minimizes the loss of operability when an abnormality occurs in a sensor or shift solenoid valve.

    Malfunction Part
    Function
    Vehicle Speed Signal
    During a vehicle speed signal malfunction, the 4th upshift is prohibited.
    Speed Sensor NT (Transmission Revolution Sensor)
    During a speed sensor NT (transmission revolution sensor) signal malfunction, the 4th upshift is prohibited.
    ATF Temperature Sensor (Transmission Wire)
    During a ATF temperature sensor (transmission wire) malfunction, the 4th upshift is prohibited.
    Shift Solenoid Valve SLT or ST
    During a shift solenoid valve SLT or ST malfunction, the 4th upshift is prohibited.
    E.F.I. Engine Coolant Temperature Sensor, Knock Control Sensor or Throttle Position Sensor
    During an E.F.I. engine coolant temperature sensor, knock control sensor or throttle position sensor malfunction, the 4th upshift is prohibited.
    Shift Solenoid Valve S1 or S2
    During a malfunction in the shift solenoid valve S1 or S2, the current to the faulty shift solenoid valve is cut off and control is effected by operating the normal shift solenoid valves. Shift control is effected as described in the table below, depending on the failed shift solenoid valve.


DIAGNOSIS
  1. When the ECM detects a malfunction, the ECM records the malfunction and memorizes the information related to the fault. Furthermore, the ECM illuminates or blinks the MIL in the combination meter assembly to inform the driver.

  2. The ECM will also store the Diagnostic Trouble Codes (DTCs) of the malfunctions. The DTCs stored in the ECM are output to the Techstream via the ECM and the DLC3.

  3. For details, refer to the Repair Manual.