BODY STRUCTURE (for Sedan) > DETAILS



FUNCTION


  1. Impact Absorbing Structure for Frontal Collision



    1. A lower front member and reinforcements are used on the upper and rear end sections of the front side member reinforcement sub-assembly, creating a structure that efficiently transmits and absorbs the impact energy through the front side member reinforcement sub-assembly.


      Y112017E01


      Text in Illustration 
      *1
      Lower Front Member
      *2
      Front Side Member Reinforcement Sub-assembly
      *3
      Reinforcement
      *4
      Reinforcement



    2. Energy absorption pads that use materials with excellent sound absorption performance are used on the lower section of the dash panel sub-assembly, helping reduce injuries to the legs and ensuring NV performance.


      Y112018


      Text in Illustration 
      V100145
      Energy Absorption Pad
      -
      -

  2. Impact Absorbing Structure for Side Collision

    1. High strength sheet steel is used in the center body pillar outer reinforcement, minimizing cabin deformation.



  3. Lessening Pedestrian Injury



    1. The cowl has an energy absorbing structure, helping lessen the impact from the upper section on the heads of pedestrians.


      Y112019E01


      Text in Illustration 
      *1
      Hood Sub-assembly
      *2
      Outer Cowl Top Panel
      *a
      Energy Absorbing Structure
      -
      -



  4. Aerodynamics

    1. A rear spoiler sub-assembly is provided, realizing the excellent aerodynamic performance.



    2. A rear wheel house plate front is available.


      Y128919E01


      Text in Illustration 
      *1
      Rear Wheel House Plate Front
      *2
      Rear Spoiler Sub-assembly


CONSTRUCTION


  1. Lightweight and Highly Rigid Body



    1. High strength sheet steel is used in order to realize excellent body rigidity and a lightweight body.


      Y112356


      Text in Illustration 
      V100145
      High Strength Steel Sheet
      -
      -



  2. Body Shell Construction



    1. The front side member reinforcement sub-assembly and the rear end of the front suspension crossmember sub-assembly are joined with a bolt, helping ensure the rigidity of the body.


      Y112357E01


      Text in Illustration 
      *1
      Front Side Member Reinforcement Sub-assembly
      *2
      Front Suspension Crossmember Sub-assembly
      *3
      Bolt
      -
      -



    2. Efficient reinforcements are used around the installation location of the rear shock absorber assembly, helping ensure the torsional rigidity of the body.


      Y112358E01


      Text in Illustration 
      *1
      Upper Back Panel Sub-assembly
      *2
      Rear Shock Absorber Plate
      *3
      Rear Roof Side Inner
      *4
      Lower Body Back Panel Sub-assembly
      *5
      Lower Back Gusset Upper
      *6
      Rear Floor Side Member Sub-assembly



  3. Anti-corrosion Sheet Steel



    1. Anti-corrosion sheet steel is used in all areas other than the interior parts.


      Y112359


      Text in Illustration 
      V100145
      Anti-corrosion Sheet Steel
      -
      -

  4. Wax and Sealer

    1. Wax and sealer are applied to hemmed portions of the hood, door panels, rocker panels, fuel lid hinge and luggage compartment door to ensure rust-resistant performance.

  5. Under Coat

    1. Acrylic acid resin is applied to the under side of the body, inside the wheel housing and other parts that are susceptible to stone chipping damage, thus improving the rust-resistant performance of these areas.

  6. Anti-chipping Application

    1. Anti-chipping paint is used on parts to protect the paint surface from objects such as gravel.



  7. Low Vibration and Low Noise Body



    1. The locations of the sound insulation materials in the frame cross sections have been optimized, creating a quiet drive.


      Y112360E01


      Text in Illustration 
      *a
      A-A Cross Section
      *b
      B-B Cross Section
      *c
      C-C Cross Section
      *d
      D-D Cross Section
      *e
      E-E Cross Section
      *f
      F-F Cross Section
      *g
      G-G Cross Section
      -
      -
      V100145
      Foamed Seal Material
      V100144
      Foamed Urethane Material

    2. The front floor panel is curved and the rigidity of the panel has been ensured, restricting vibration.

    3. A front floor panel reinforcement is used on the front of the tunnel section, restricting the movement of the body frame and reducing vibration.



    4. 2 bulkheads are used on the inner side in the rocker panel, restricting the movement of the body frame and reducing vibration.


      Y112361E01


      Text in Illustration 
      *1
      Front Floor Panel Reinforcement
      *2
      Bulkhead
      V100145
      Curved Area
      -
      -



    5. The dash panel insulator assembly has been enlarged. At the same time, a structure is used with 2 layers of different sound absorbing materials, creating a lightweight structure and reducing the engine noise that enters the interior.


      Y112362E01


      Text in Illustration 
      *1
      Low-density Layer
      *2
      High-density Layer
      *a
      Cross Section
      -
      -
      V100135
      Interior Side
      -
      -

    6. All the locations of sound insulation and absorption materials in the cabin have been optimized, creating a quiet drive.



    7. Damping materials are used in the side door outer panel, reducing the sound when closing the doors.


      Y112363


      Text in Illustration 
      V100145
      Damping Material
      -
      -

    8. An under coat is applied on the rear of the floor, reducing splash noise.



    9. Body rocker panel mouldings are provided.


      Y112364E01


      Text in Illustration 
      *1
      Body Rocker Panel Moulding
      -
      -



  8. Parts with Low Repair Cost



    1. A radiator slide structure is used that minimizes damage to the cooling unit during a collision, reducing repair costs.


      Y112365E01


      Text in Illustration 
      *1
      Cooling Unit
      *2
      Front Bumper Reinforcement
      *a
      Before a Collision
      *b
      During a Collision



    2. The bolt-on structure is used for the rear bumper arm sub-assembly and the rear No. 1 bumper reinforcement, and the energy absorbing brackets are provided in the rear No. 1 bumper reinforcement. This structure efficiently absorbs impact energy in a rear collision, and reduces damaged parts and repair costs.


      Y112366E01


      Text in Illustration 
      *1
      Rear Bumper Arm Sub-assembly
      *2
      Rear No. 1 Bumper Reinforcement
      *3
      Energy Absorbing Brackets
      -
      -