ENGINE UNIT (for Sedan) > GENERAL



OUTLINE
  1. The 1NZ-FE engine is an in-line, 4-cylinder, 1.5 liter, 16-valve DOHC engine.



  2. The Variable Valve Timing-intelligent (VVT-i) system, Direct Ignition System (DIS) and Electronic Throttle Control System-intelligent (ETCS-i) are used on this engine in order to realize high performance, quietness, fuel economy and clean emission.


    W104600


SPECIFICATION

Engine Type
1NZ-FE
No. of Cyls. and Arrangement
4-cylinder, In-line
Valve Mechanism
16-valve DOHC, Chain Drive (with VVT-i)
Combustion Chamber
Pentroof Type
Flow of Intake and Exhaust Gasses
Cross-Flow
Fuel System
SFI
Ignition System
DIS
Displacement
1497 cm3 (91.3 cu. in.)
Bore x Stroke
75.0 mm X 84.7 mm (2.95 in. X 3.33 in.)
Compression Ratio
10.5:1
Max. Output
SAE-NET*1
79 kW @ 6000 rpm (106HP @ 6000 rpm)
Max. Torque
SAE-NET*1
139 N*m @ 4200 rpm (103 ft. *lbf @ 4200 rpm)
Valve Timing
Intake
Open
33°BTDC to 7°ATDC
Closed
12°ABDC to 55°ABDC
Exhaust
Open
42°BBDC
Closed
2°ATDC
Firing Order
1 - 3 - 4 - 2
Octane Rating
87 or higher
Research Octane Number (RON)
91 or higher
Oil Grade
ILSAC
Emission Regulation
Tailpipe
Tire2-Bin5, SFTP
Evaporative
Tier2, ORVR
Engine Service Mass*2 (Reference)
M/T
83.2 kg (183.4 lb)
A/T
77.8 kg (171.5 lb)

HINT:
*1: Maximum output and torque rating are determined by revised SAE J1349 standard.
*2: Weight shows the figure with the oil fully filled.


MAIN FEATURES
  1. The 1NZ-FE engine has achieved the following performance through the use of the items listed below.

    1. High performance and fuel economy

    2. Low noise and vibration

    3. Lightweight and compact design

    4. Good serviceability

    5. Clean emission

      Section
      Item
      (1)
      (2)
      (3)
      (4)
      (5)
      Engine Proper
      An aluminum cylinder block sub-assembly is used.


      ○


      An offset crankshaft is used.
      ○
      ○


      ○
      The taper squish shape is used for the combustion chamber.
      ○



      ○
      Valve Mechanism
      The chain sub-assembly and No. 1 chain tensioner assembly are used.
      ○

      ○
      ○

      The VVT-i system is used.
      ○



      ○
      Intake and Exhaust System
      The intake manifold made of plastic is used.


      ○


      The linkless-type throttle with motor body assembly is used.


      ○
      ○

      The stainless steel exhaust manifold is used.


      ○


      2 Three-Way Catalytic converters (TWCs) are used.




      ○
      A rearward exhaust layout is used to realize the early activation of the catalyst.




      ○
      Fuel System
      The 12-hole type fuel injector assemblies are used.
      ○




      The fuel returnless system is used.


      ○
      ○
      ○
      The quick connectors are used to connect the fuel hose with the fuel pipes.



      ○

      Ignition System
      The long-reach type spark plugs are used.
      ○




      The Direct Ignition System (DIS) makes ignition timing adjustment unnecessary.
      ○


      ○
      ○
      Engine Control System
      The Electronic Throttle Control System-intelligent (ETCS-i) is used.
      ○



      ○
      The non-contact sensor is used in the throttle position sensor and accelerator pedal position sensor.
      ○




      The cranking hold function is used.
      ○




      The evaporative emission control system is used.




      ○
      The use of an air fuel ratio sensor allows for precise control.




      ○