SFI SYSTEM (for Hatchback) > DETAILS



FUNCTION OF MAIN COMPONENTS
  1. The main components of the 1NZ-FE engine control system are as follows.

    Components
    Outline
    Quantity
    Function
    ECM
    32-bit CPU
    1
    The ECM optimally controls the SFI, ESA and IAC to suit the operating conditions of the engine in accordance with the signals provided by the sensors.
    Crank Position Sensor (Rotor Teeth)
    Pickup Coil Type (36-2)
    1
    This sensor detects the engine speed and performs the cylinder identification.
    Cam Position Sensor (Rotor Teeth)
    Pickup Coil Type (3)
    1
    This sensor performs cylinder identification.
    Knock Control Sensor
    Built-in Piezoelectric Element Type (Flat Type)
    1
    This sensor detects an occurrence of the engine knocking indirectly from the vibration of the cylinder block caused by the occurrence of engine knocking.
    Intake Mass Air Flow Meter Sub-assembly
    Hot-wire Type
    1
    This sensor has a built-in hot-wire to directly detect the intake air mass.
    Throttle Position Sensor
    Non-contact Type
    1
    This sensor detects the throttle valve opening angle.
    Oxygen Sensor
    Cup Type with Heater
    1
    This sensor detects the oxygen concentration in the exhaust emission by measuring the electromotive force which is generated in the sensor itself.
    Air Fuel Ratio sensor
    Planar Type with Heater
    1
    As with the oxygen sensor, this sensor detects the oxygen concentration in the exhaust emission. However, it detects the oxygen concentration in the exhaust emission linearly.
    Accelerator Pedal Sensor Assembly
    Non-contact Type
    1
    This sensor detects the amount of pedal effort applied to the accelerator pedal.
    Fuel Injector Assembly
    12-hole Type
    4
    The injector is an electromagnetically operated nozzle which injects fuel in accordance with signals from the ECM.
    E.F.I. Engine Coolant Temperature Sensor
    Thermistor Type
    1
    This sensor detects the water temperature by means of an internal thermistor.


SYSTEM CONTROL
  1. The engine control system of the 1NZ-FE engine has the following systems.

    Components
    Function
    Sequential Multiport Fuel Injection (SFI)
    An L-type SFI system is used, the intake air mass is detected with a hot-wire type air flow meter. The fuel injection system is a sequential multiport fuel injection system.
    Electronic Spark Advance (ESA)
    The ECM determines the optimal ignition timing in accordance with the signals received from the sensors and sends (IGT) ignition signal to the igniter. The ECM corrects ignition timing in response to engine knocking.
    Electronic Throttle Control System-intelligent (ETCS-i)
    Optimally controls the throttle valve opening in accordance with the amount of accelerator pedal effort, the throttle valve opening control request from the ECM, and the condition of the engine and the vehicle.
    Variable Valve Timing-intelligent (VVT-i)
    Regulates operation of the intake camshaft to ensure optimal valve timing in accordance with engine operating conditions.
    Fuel Pump Control
    Fuel pump operation is controlled by signals from the ECM. The fuel pump is stopped when the SRS airbags deploy.
    Cooling Fan Control
    Cooling fan operation is controlled by signals from the ECM based on the E.F.I. engine coolant temperature sensor signal.
    Air Fuel Ratio Sensor and Oxygen Sensor Heater Control
    Maintains the temperature of the air fuel ratio sensor or oxygen sensor at an appropriate level to realize accuracy of detection of the oxygen concentration in the exhaust gas.
    Evaporative Emission Control
    1. The ECM controls the purge flow of evaporative emissions (HC) in the canister in accordance with engine conditions.
    2. Approximately 5 hours after the ignition switch has been turned off, the ECM operates the canister pump module to detect any evaporative emission leakage occurring in the evaporative emission control system through changes in the 0.02 in. leak pressure.
    Engine Immobiliser
    Prohibits fuel delivery and ignition if an attempt is made to start the engine with an invalid key.
    Air Conditioning Cut-off Control*
    By turning the air conditioning compressor on or off in accordance with engine operating conditions, drivability is maintained.
    Brake Override System
    Restricts the driving torque when both the accelerator and brake pedals are depressed. (For the Activation Conditions and Inspection Method, refer to the repair manual)

    1. *: Models with air conditioning system



  2. Variable Valve Timing-intelligent (VVT-i) System



    1. The VVT-i system is designed to control the intake camshaft within a range of 40° (of Crankshaft Angle) to provide valve timing that is optimally suited to the engine conditions. This improves torque in all speed ranges as well as increasing fuel economy and reducing exhaust emissions.


      W104586E01


      W105002E01

    2. The VVT-i system delivers excellent benefit vehicle states as shown in the table below.

      Operation State
      Objective
      Effect
      1. During Idling
      2. At Light Load
      W105009E01
      Eliminating overlap to reduce blow back to the intake side.
      1. Stabilized idling rpm
      2. Better fuel economy
      At Medium Load
      W105010E01
      Increasing overlap to increase internal EGR to reduce pumping loss.
      1. Better fuel economy
      2. Improved emission control
      In Low to Medium Speed Range with Heavy Load
      W105010E01
      Advancing the intake valve close timing for volumetric efficiency improvement.
      Improved torque in low to medium speed range
      In High Speed Range with Heavy Load
      W105011E01
      Retarding the intake valve close timing for volumetric efficiency improvement.
      Improved output
      At Low Temperatures
      W105012E01
      Eliminating overlap to prevent blow back to the intake side leads to the lean burning condition, and stabilizes the idling speed at fast idle.
      1. Stabilized fast idle rpm
      2. Better fuel economy
      1. Upon Starting
      2. Stopping the Engine
      W105012E01
      Eliminate overlap to reduce blow back to the intake side.
      Improved startability

  3. Fuel Pump Control

    1. In this system, the airbag deployment signal from the airbag assembly is detected by the ECM, and it turns off the circuit opening relay. After the fuel cut control has been activated, turning the ignition switch from off to on cancels the fuel cut control and the engine can be restarted.

  4. Cooling Fan Control

    1. A cooling fan control system controlled to achieve an optimal fan speed in accordance with the E.F.I. engine coolant temperature and air conditioning operating conditions.


CONSTRUCTION


  1. ECM



    1. The ECM is installed in the engine compartment. As a result, the wiring harness has been shortened, thus realizing weight reduction.


      W104981E01


      Text in Illustration 
      *1
      ECM
      -
      -



  2. Crank Position and Cam Position Sensors

    1. Pick-up coil type sensors are used for the crank position, cam position sensor.

    2. The timing sprocket of the crankshaft has 34 teeth, with 2 teeth missing. Based on these teeth, the crank position sensor transmits crank position signals (NE signal) consisting of 33 high or low output pulses every 10° per revolution of the crankshaft, and 1 high or low output pulse every 30°. The ECM uses the NE signal for detecting the crank position as well as for detecting the engine speed. It uses the missing teeth signal for determining the top dead center.



    3. To detect the cam position, a timing rotor on the intake camshaft is used to generate 3 (3 high output, 3 low output) pulses for every 2 revolutions of the crankshaft.


      W103894E01


      Text in Illustration 
      *1
      Crank Position Sensor
      *2
      Timing Sprocket
      *3
      Cam Position Sensor
      *4
      Timing Rotor

      W105014E01



  3. Camshaft Timing Oil Control Valve Assembly



    1. This camshaft timing oil control valve assembly controls the spool valve using duty cycle control from the ECM. This allows hydraulic pressure to be applied to the VVT-i controller advance or retard side. When the engine is stopped, the camshaft timing oil control valve assembly is will move to the retarded position.


      W104588E01


      Text in Illustration 
      *1
      Spring
      *2
      Sleeve
      *3
      Spool Valve
      -
      -
      *a
      To Intake VVT-i Controller (Advance Side)
      *b
      To Intake VVT-i Controller (Retard Side)
      *c
      Drain
      *d
      Oil Pressure



  4. Knock control sensor (Flat Type)

    1. In a conventional knock control sensor (resonant type), a vibration plate is built into the sensor. This plate has the same resonance point as the knocking frequency of the engine block. This sensor can only detect vibration in this frequency band.

    2. A flat type knock control sensor (non-resonant type) has the ability to detect vibration in a wider frequency band (from about 6 kHz to 15 kHz). It has the following features.



    3. The engine knocking frequency will vary slightly depending on the engine speed. The flat type knock control sensor can detect vibration even when the engine knocking frequency changes. Due to the use of the flat type knock control sensor, the vibration detection ability is increased compared to a conventional type knock control sensor, and more precise ignition timing control is possible.


      W100530E02

    4. A flat type knock control sensor is installed to an engine by placing it over the stud bolt installed on the cylinder block sub-assembly. For this reason, a hole for the stud bolt exists in the center of the sensor.

    5. In the sensor, a steel weight is located in the upper portion. An insulator is located between the weight and a piezoelectric element.



    6. An open/short circuit detection resistor is integrated in the sensor. When the ignition is ON, the open/short circuit detection resistor in the knock control sensor and the resistor in the ECM keep the voltage at terminal KNK1 constant. An Integrated Circuit (IC) in the ECM constantly monitors the voltage of terminal KNK1. If the open/short circuit occurs between the knock control sensor and the ECM, the voltage of terminal KNK1 will change and the ECM will detect the open/short circuit and store a Diagnostic Trouble Code (DTC).


      W104701E05


      Text in Illustration 
      *A
      Flat Type Knock Control Sensor (Non-Resonant Type)
      *B
      Conventional Type Knock Control Sensor (Resonant Type)
      *1
      Steel Weight
      *2
      Insulator
      *3
      Piezoelectric Element
      *4
      Open Circuit Detection Resistor
      *5
      Vibration Plate
      -
      -

      W101046E04



    7. Vibrations caused by knocking are transmitted to the steel weight. The inertia of this weight applies pressure to the piezoelectric element. This action generates electromotive force.


      W101072E05


      Text in Illustration 
      *1
      Steel Weight
      *2
      Piezoelectric Element
      V100135
      Inertia
      -
      -



  5. Intake Mass Air Flow Meter Sub-assembly

    1. The compact and lightweight intake mass air flow meter sub-assembly, which is a plug-in type, allows a portion of the intake air to flow through the detection area. By directly measuring the mass and the flow rate of the intake air, the detection precision is ensured and the intake air resistance is reduced.



    2. This intake mass air flow meter sub-assembly has a built-in intake air temperature sensor.


      W103925E02


      Text in Illustration 
      *1
      Temperature Sensing Element
      *2
      Hot-wire Element
      *3
      Intake Air Temperature Sensor
      -
      -
      V100135
      Air Flow
      -
      -



  6. Throttle Position Sensor



    1. The throttle position sensor is mounted on the throttle with motor body assembly to detect the opening angle of the throttle valve. The throttle position sensor converts the magnetic flux density that changes when the magnetic yoke (located on the same axis as the throttle shaft) rotates around the Hall IC into electric signals to operate the throttle control motor.


      W103926E01


      Text in Illustration 
      *1
      Throttle Control Motor
      *2
      Throttle Position Sensor
      *3
      Throttle Valve
      *4
      Return Spring

      W103927E01



  7. Air Fuel Ratio Sensor and Oxygen Sensor

    1. The air fuel ratio sensor and oxygen sensor differ in output characteristics.

    2. Compared to the conventional type (cup type), the sensor and heater portions of the planar type are narrower overall. Because the heat of the heater acts directly on the alumina and zirconia (of the sensor portion), it accelerates the activation of the sensor.



    3. The output voltage of the oxygen sensor changes in accordance with the oxygen concentration in the exhaust emission. The ECM uses this output voltage to determine whether the present air fuel ratio is richer or leaner than the stoichiometric air fuel ratio.


      W100959E06

    4. The basic constructions of the air fuel ratio sensor and oxygen sensor are the same. However, they are divided into the cup type and the planar type, according to the different types of heater construction that are used.

    5. The cup type sensor contains a sensor element that surrounds a heater.



    6. The planer type sensor uses alumina, which excels in heat conductivity and insulation, to integrate a sensor element with a heater, thus realizing the excellent warm-up performance of the sensor.


      W105018E02


      Text in Illustration 
      *A
      Air-fuel Ratio Sensor (Planer Type)
      *B
      Oxygen Sensor (Cup Type)
      *1
      Alumina
      *2
      Dilation Layer
      *3
      Atmosphere
      *4
      Heater
      *5
      Sensor Element (Zirconia)
      *6
      Platinum Electrode



  8. Accelerator Pedal Sensor Assembly

    1. The non-contact type accelerator pedal position sensor used a Hall IC.

    2. The magnetic yoke that is mounted at the accelerator pedal arm rotates around the Hall IC in accordance with the amount of effort that is applied to the accelerator pedal. The Hall IC converts the changes in the magnetic flux that occur at that time into electrical signals, and outputs them as accelerator pedal effort to the ECM.



    3. The Hall IC contains circuits for the main and sub signals. It converts the accelerator pedal depressed angles into electric signals with two differing characteristics and outputs them to the ECM.


      W104702E02


      Text in Illustration 
      *1
      Magnetic Yoke
      *2
      Accelerator Pedal Arm
      *3
      Magnet
      *4
      Hall IC
      *a
      Internal Construction
      *b
      A-A Cross Section

      W103928E02



  9. No. 1 Ignition Coil

    1. An igniter is integrated with the ignition coils, which are provided independently in each cylinder. This improves ignition timing accuracy, reduces high-voltage loss and enhances the overall reliability of the ignition system by eliminating the distributor.



    2. The spark plug caps, which provide contact to spark plugs, are integrated with an ignition coil. Also, an igniter is enclosed to simplify the system.


      W104593E01


      Text in Illustration 
      *1
      Igniter
      *2
      Iron Core
      *3
      Secondary Coil
      *4
      Primary Coil
      *5
      Spark Plug Cap
      -
      -



  10. Spark Plug



    1. Iridium-tipped spark plugs improve ignition performance while maintaining the same durability as platinum-tipped spark plugs.


      W104983E01


      Text in Illustration 
      *1
      Iridium Tip
      -
      -


OPERATION


  1. Variable Valve Timing-intelligent (VVT-i) System



    1. Using the engine speed, vehicle speed, intake air mass, throttle position and water temperature, the ECM can calculate optimal valve timing for each driving condition (target valve timing). The ECM uses this calculated timing to control the camshaft timing oil control valves. In addition, the ECM uses signals from the cam position sensor and the crank position sensor to detect the actual valve timing, thus providing feedback control to achieve the target valve timing.


      W104703E01



    2. When the camshaft timing oil control valve assembly is operated as illustrated below by the advance signals from the ECM, the resultant oil pressure is applied to the timing advance side vane chamber to rotate the camshaft in the timing advance direction.


      W105063E01



    3. When the camshaft timing oil control valve assembly is operated as illustrated below by the retard signals from the ECM, the resultant oil pressure is applied to the timing retard side vane chamber to rotate the camshaft in the timing retard direction.


      W105064E01

    4. After reaching the target valve timing, the valve timing is held by keeping the camshaft timing oil control valve assembly in the neutral position unless the traveling state changes. This adjusts the valve timing at the desired target position and prevents the engine oil from running out when it is unnecessary.



  2. Fuel Pump Control

    1. The fuel pump control is used to stop the fuel pump when the airbags deploy in a front or side collision.

    2. In this system, the airbag deployment signal from the airbag sensor assembly is detected by the ECM, which turns off the circuit opening relay.



    3. After the fuel cut control has been activated, turning the ignition switch from off to ON cancels the fuel cut control, and the engine can be restarted.


      W104984E01



  3. Cooling Fan Control

    1. On the models without air conditioning system, the ECM controls the operation of the cooling fan based on the E.F.I. engine coolant temperature sensor signal.



    2. On the models with air conditioning, the ECM controls the operation of the cooling fan in two speeds (low and high) based on the E.F.I. engine coolant temperature sensor signal and the air conditioning amplifier assembly signal. The low speed operation is accomplished by applying the current through a resistor, which reduces the speed of the cooling fan.


      W100970E07


      Engine Coolant Temperature
      Cooling Fan Drive Request Signal
      Cooling Fan Operation
      Low
      Off
      Off
      Low
      Low
      High
      High
      High
      Off
      High
      Low
      High
      High
      High


FAIL-SAFE
  1. When the ECM detects a malfunction, the ECM stops or controls the engine according to the data already stored in the memory. For details, refer to the Repair Manual.


DIAGNOSIS
  1. When the ECM detects a malfunction, the ECM diagnoses and memorizes the failed section. For details, refer to the Repair Manual.