OCCUPANT CLASSIFICATION SYSTEM (for Sedan) > DETAILS



FUNCTION OF MAIN COMPONENTS
  1. The main components have the following functions:

    Component
    Function
    Occupant Detection ECU
    Judges whether the front passenger seat is occupied using signals from 4 occupant classification sensors and front passenger seat belt buckle switch.
    Occupant Classification Sensor
    The resistance values of these sensors, which vary in accordance with the distortion that acts on the brackets, are output to the occupant detection ECU.
    Front Seat Inner Belt Assembly RH
    Seat Belt Buckle Switch
    Detects if the front passenger seat belt is fastened.
    Combination Meter Assembly
    SRS Warning Light
    Turns on up to alert the driver when the airbag sensor assembly detects a malfunction in the airbag system.
    Front Passenger Airbag ON/OFF Indicator
    AIRBAG ON/OFF Indicator Lights
    1. Inform the driver whether the occupant detection ECU puts the instrument panel passenger airbag without door assembly and front seat outer belt assembly RH into an active state or inactive state.
    2. If a malfunction occurs in the occupant classification system, the AIRBAG OFF indicator light and the SRS warning light come on.
    Front Passenger Seat Belt Reminder Light
    Illuminates to alert the driver or front passenger if the front passenger's seat belt is not fastened when the front passenger seat is occupied.


OPERATING CONDITION
  1. This system makes the following judgments: unoccupied judgment, child seat judgment, child judgment and adult judgment. In addition, it performs an initial check to check the circuit of the AIRBAG ON/OFF indicator lights when the ignition switch is ON.

    1. The occupant detection ECU constantly monitors the weight of the front passenger seat, and makes a judgment in accordance with the signals from the occupant classification sensor and the state of the seat belt buckle switch, regardless of the position of the ignition switch.

    2. The occupant detection ECU contains criteria value "A" to judge whether the seat is being occupied by a child or a child seat in accordance with the signals from the 4 occupant classification sensors and seat belt buckle switch, and criteria value "B" to judge whether the occupant is an adult or child (with child seat).

    3. The occupant detection ECU makes an occupied or unoccupied judgment in accordance with the signals from the seat belt buckle switch.


SYSTEM CONTROL


  1. Unoccupied Judgment

    1. The occupant detection ECU makes an unoccupied judgment when the judgment value is lower than criteria value "A" and the seat belt buckle switch is off.



    2. If the ignition switch is turned ON in this state, the system performs an initial check, and does not illuminate the AIRBAG ON/OFF indicator lights. Then, the system prohibits the deployment of the instrument panel passenger airbag without door assembly and the front seat outer belt assembly RH, and does not blink the front passenger seat belt reminder light.


      Y128904E01



  2. Child Seat or Child Judgment

    1. If the judgment value is lower than criteria value "B" and the seat belt buckle switch is on, the occupant detection ECU judges that a child seat is installed.

    2. If the judgment value is higher than criteria value "A", but lower than criteria value "B", and the seat belt buckle switch is off, the occupant detection ECU judges that the seat is being occupied by a child.



    3. When the ignition switch is turned ON under these conditions, the system performs an initial check and illuminates the AIRBAG OFF indicator light to indicate that the instrument panel passenger airbag without door assembly has been deactivated.


      Y128905E01

    4. After the occupant detection ECU judges that child seat is installed, the AIRBAG OFF indicator light does not go off unless the seat belt buckle switch is turned off.



  3. Adult Judgment

    1. When the judgment value is higher than criteria value "B", the occupant detection ECU judges that the seat is being occupied by an adult.



    2. If the ignition switch is turned ON in this state, the system performs an initial check and illuminates the AIRBAG ON indicator light, indicating that the instrument panel passenger airbag without door assembly is active.


      Y128906E01

    3. After the occupant detection ECU judges that the occupant is an adult, and if the judgment value is determined as criteria value "B" or less according to occupant load movement, the ECU continues adult judgment for approximately 10 seconds before switching to the child judgment.



  4. Initial Check



    1. After the ignition switch is tuned ON, the occupant detection ECU lights up the AIRBAG ON/OFF indicator lights via the airbag sensor assembly based on the timing chart below in order to check the indicator light circuits.


      Y103047E05


CONSTRUCTION


  1. Occupant Classification Sensor



    1. The occupant classification sensors are installed on 4 brackets connecting the seat rail and the seat frame. The resistance values of these sensors which vary in accordance with the distortion that acts on the brackets are output to the occupant detection ECU.


      Y112400E02


DIAGNOSIS
  1. If the occupant detection ECU detects a malfunction in the occupant classification system, it stores the malfunction data in memory via the airbag sensor assembly, illuminating the SRS warning light and AIRBAG OFF indicator light.

  2. The occupant detection ECU outputs 5-digit DTCs to the Techstream.

  3. Only 5-digit DTCs are available for the occupant classification system.

  4. The 5-digit DTC can be read by connecting the Techstream to the DLC3 terminal.



  5. For details, refer to the Repair Manual.


    Y112401E02