METER / GAUGE SYSTEM (for Hatchback) > DETAILS



OPERATING CONDITION
  1. Eco Driving Indicator Light (Models with Automatic Transaxle)

    1. Eco Driving Indicator Light starts to operate when all of the following conditions are met:

      Conditions
      Ignition switch is ON.
      Engine is running.
      Shift lever is in D.
      When the vehicle is at a speed of 130 km/h (81 mph) or below.

    2. Eco Driving Indicator Light stops operation when any of the following conditions is met:

      Conditions
      Ignition switch is off.
      Engine is stopping.
      Shift lever is in any position other than D.
      When the vehicle is at a speed of 130 km/h (81 mph) or over.


SYSTEM CONTROL
  1. Front Seat Belt Warning

    1. When the ignition switch is ON, this system detects the state of the seat belts based on the signals from the front seat belt buckle switch LH and RH and the occupant classification sensors.

    2. The front seat belt warning light located in the combination meter is used for both the driver and passenger seats.

    3. After the ignition switch is turned ON, if the driver's or front passenger's seat belt has remained unfastened for 1.8 seconds, the front seat belt warning light will flash for 6 seconds. And then, when either of the following conditions is met, the seat belt warning light will continue flashing; the driver's or front passenger's seat belt remains unfastened and the shift lever is in a position other than P for approximately 30 seconds or more, or the driver's or front passenger's seat belt remains unfastened and the seat belt warning buzzer sounds once. Furthermore, when the seat belt is not fastened within approximately 30 seconds from the time the seat belt warning buzzer started sounding periodically, the warning light will commence flashing at short intervals.

    4. If the driver's or front passenger's seat belt is still unfastened even after the ignition switch is turned ON, the seat belt warning buzzer will sound 5 times. And then, if the driver's or front passenger's seat belt remains unfastened and the vehicle speed reaches approximately 20 km/h (12.4 mph), the seat belt warning buzzer will sound once. Furthermore, when approximately 30 seconds has elapsed with the seat belt unfastened, the seat belt warning buzzer will start sounding periodically for 9.6 seconds. If the seat belt is not fastened within this 9.6 seconds, the seat belt warning buzzer will commence sounding at short intervals.

    5. While the seat belt warning light is flashing and the seat belt warning buzzer is sounding, fastening the seat belt will bring the warning light flashing and warning buzzer sounding to a stop.



  2. Eco Driving Indicator Light (Models with Automatic Transaxle)



    1. When the ECM determines that Eco driving (environment-friendly acceleration operation) is being performed, the ECM outputs an Eco Driving Indicator Light illumination request to the combination meter assembly that illuminates the Eco Driving Indicator Light.


      Y101366E01

  3. Maintenance Required Reminder Light (Models for U.S.A.)

    1. A maintenance required reminder light will appear to remind the driver to have maintenance performed based on the vehicle driving distance.

    2. The Combination meter assembly calculates the vehicle driving distance based on the signals from the skid control ECU.

    3. When the accumulated vehicle driving distance memorized in the meter ECU exceeds 4500 miles after being reset, the meter ECU will flash the maintenance required reminder light for approximately 16 seconds after the bulb check and remind the driver that the vehicle maintenance needs to be conducted shortly.

    4. When the accumulated vehicle driving distance memorized in the meter ECU exceeds 5000 miles after being reset, the meter ECU will illuminate the maintenance required reminder light immediately and keep it on to remind the driver to have the vehicle serviced.

    5. After maintenance has been performed, the accumulated vehicle driving distance memorized in the combination meter assembly should be reset to zero using the ODO/TRIP DISP switch.

      HINT:
      1. The accumulated vehicle driving distance memorized in the combination meter assembly can be reset using the following procedure.
        1. Turn the ignition switch ON, and make sure that the trip A is displayed on multi-information display.
        2. Turn the ignition switch off. While pushing the ODO/TRIP DISP switch, turn the ignition switch to ON.
        3. With the ignition switch ON, keep holding the ODO/TRIP DISP switch (for at least 5 seconds) with the multi-information display counting down. Release the ODO/TRIP DISP switch when the resetting procedure has completed.
        4. As the resetting completes, the odometer will display "000000" for 1 second.


FUNCTION
  1. Buzzer Function

    1. The table below shows the buzzer in the combination meter assembly:

      Item
      1. Front Seat Belt Warning
      2. EPS Warning
      3. Key Reminder
      4. Engine Immobiliser Matching Completion Report
      5. Parking Brake On Driving Warning
      6. Door Open Driving Warning
      7. Light Reminder
      8. Turn Flasher Sound



  2. Multi-information Display Function


    Y111217E01


    Text in Illustration 
    *1
    Multi-information Display
    -
    -

    Display Area
    Display
    Display Item
    Outline
    "a"
    Y111222
    Clock Display
    The clock is always displayed.
    "b"
    Y111293
    Outside Temperature Display
    The outside temperature is always displayed.
    "c"
    Y111239
    Odometer Display
    Displays the odometer.
    Y111240
    Trip Meter A Display
    Displays the trip meter A.
    Y111241
    Trip Meter B Display
    Displays the trip meter B.
    Y111242
    Instantaneous Fuel Consumption Display
    1. Displays the value that has been calculated by the combination meter assembly, which is based on the distance driven and the fuel consumption volume.
    2. This display is updated constantly.
    Y111243
    Average Fuel Consumption After Refueling Display
    1. Displays the value that has been calculated by the combination meter assembly, which is based on the distance driven after refueling and the fuel consumption.
    2. The combination meter assembly resets the value when determining that the vehicle has been refueled according to the signal from the fuel sender gauge.
    3. This display is updated every 10 seconds.
    Y111244
    Drivable Distance Display
    1. Displays the value that has been calculated by the combination meter assembly, which is based on the elapsed time and distance driven after the ignition switch, has been turned to ON.
    2. This display is updated every 1 second.
    Y111245
    Average Vehicle Speed After Starting Display
    1. Displays a value that has been calculated by the combination meter assembly based on the vehicle speed signal and the elapsed time since the engine start signal.
    2. This display is updated every 10 seconds.
    Y111235
    Eco Driving Indicator Light Customizing Display*
    Customize Eco Driving Indicator Light.
    "d"
    Y111236
    Shift Position Indicator*
    Displays shift position P, R, N, D, 2 or 1 of the automatic transaxle.
    1. *: Models with automatic transaxle


OPERATION


  1. Switching the Multi-information Display



    1. The multi-information display changes in the order shown below by pressing the ODO/TRIP DISP switch.


      Y111220E01


      Text in Illustration 
      *A
      Models with Automatic Transaxle
      -
      -
      *1
      ODO/TRIP DISP Switch
      *2
      Eco Driving Indicator Light Customizing Display: Eco On.
      *3
      Eco Driving Indicator Light Customizing Display: Eco Off.
      *4
      Odometer Display
      *5
      Trip Meter A Display
      *6
      Trip Meter B Display
      *7
      Instantaneous Fuel Consumption Display
      *8
      Average Fuel Consumption After Refueling Display
      *9
      Drivable Distance Display
      *10
      Average Vehicle Speed After Starting Display
      V100135
      Pressing the ODO/TRIP DISP switch
      V100136
      Pressing the ODO/TRIP DISP switch for approximately 5 seconds
      V100137
      Pressing the ODO/TRIP DISP switch for approximately 2 seconds
      -
      -