Home › Brake › BRAKE (FRONT) › FRONT BRAKE (for Sedan)

FRONT BRAKE (for Sedan) > INSTALLATION



1. INSTALL FRONT DISC


C108932E02
  1. Align the matchmarks of the disc and axle hub and install the disc.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    When replacing the disc, select the position that gives the minimum disc runout.



2. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING
  1. Install the disc brake cylinder mounting to the steering knuckle with the 2 bolts.

    Torque:
    107 N*m{ 1089 kgf*cm , 79 ft.*lbf }



3. INSTALL NO. 1 BUSH DUST BOOT


    C190241E04
  1. Apply lithium soap base glycol grease to 2 new dust boots.
    Text in Illustration 
    *1
    Lithium Soap Base Glycol Grease

    HINT:
    Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each front disc brake bush dust boot.

  1. Install the 2 dust boots onto the disc brake cylinder mounting.



4. INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSH


    C190224E08
  1. Apply lithium soap base glycol grease to the slide pins and a new slide bush, as shown in the illustration.
    Text in Illustration 
    *1
    Lithium Soap Base Glycol Grease
    *2
    Slide Pin (Upper)
    *3
    Slide Pin (Lower)
    *4
    Slide Bush

  1. Install the slide bush onto the slide pin (lower).



5. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN
  1. Install the slide pin (upper) and slide pin (lower) onto the cylinder mounting.



6. INSTALL FRONT ANTI SQUEAL SHIM KIT
  1. Install the 4 disc brake pad support plates onto the disc brake cylinder mounting.

  1. Install the indicator plates onto the upper side of the brake pad.



    C190258E03
  1. Apply disc brake grease to both sides of each No. 1 anti-squeal shim.
    Text in Illustration 
    *1
    Disc Brake Grease
    *2
    No. 1 Anti-squeal Shim



    C190259E02
  1. Install the anti squeal shims onto each brake pad.
    Text in Illustration 
    *1
    No. 1 Anti Squeal Shim
    *2
    No. 2 Anti Squeal Shim



7. INSTALL FRONT DISC BRAKE PAD KIT (PAD ONLY)
  1. Install the 2 disc brake pads onto the disc brake cylinder mounting.

    NOTICE:
    There should be no oil or grease on the friction surfaces of the disc brake pads or the front disc.



8. INSTALL DISC BRAKE CYLINDER ASSEMBLY
  1. Install the disc brake cylinder onto the disc brake cylinder mounting with the 2 bolts.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }



9. CONNECT FRONT FLEXIBLE HOSE


C107599E01
  1. Connect the flexible hose with a new union bolt and a new gasket.
    Text in Illustration 
    *a
    Lock Hole

    Torque:
    30 N*m{ 310 kgf*cm , 22 ft.*lbf }

    HINT:
    Install the flexible hose lock securely into the lock hole in the disc brake cylinder.



10. FILL RESERVOIR WITH BRAKE FLUID


C241208
  1. Disengage the 3 clips and separate the hood to cowl top seal.

  1. Remove the cowl top ventilator louver.



    C241209
  1. Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3



11. BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.



    C274940
  1. Using a 10 mm union nut wrench, disconnect the 2 brake tubes from the master cylinder.



    C121826
  1. Slowly depress the brake pedal and hold it there (Step A).



    C121827
  1. Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat step A and B 3 or 4 times.



    C274940
  1. Using a 10 mm union nut wrench, connect the 2 brake tubes to the master cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



12. BLEED BRAKE LINE


C116913
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).

  1. Repeat step C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



13. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3



14. INSPECT FOR BRAKE FLUID LEAK


15. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }