Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM (for Sedan)

SFI SYSTEM (for Sedan) > FREEZE FRAME DATA



DESCRIPTION
  1. Freeze frame data records the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, it can help determine if the vehicle was running or stopped, the engine was warmed up or not, the air-fuel ratio was Lean or Rich, and other data, from the time the malfunction occurred.

    HINT:
    If it is impossible to duplicate the problem even though a DTC is detected, confirm the freeze frame data.


  1. A159471E09
    The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using a Techstream, five separate sets of freeze frame data, including the data values at the time when the DTC was stored, can be checked.
    1. 3 data sets before the DTC was stored.
    2. 1 data set when the DTC was stored.
    3. 1 data set after the DTC was stored.
    1. These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.

LIST OF FREEZE FRAME DATA

Tester Display
Measure Item
Diagnostic Note
Vehicle Speed
Vehicle speed
Speed indicated on speedometer
Engine Speed
Engine speed
-
Calculate Load
Calculated load
Calculated load by ECM
Vehicle Load
Vehicle load
-
MAF
Mass air flow volume
If approximately 0.0 gm/sec:
  1. Mass air flow meter power source circuit open or short
  1. VG circuit open or short
If 160.0 gm/sec or more:
  1. E2G circuit open
Atmosphere Pressure
Atmospheric pressure
Equivalent to atmospheric pressure
Coolant Temp
Engine coolant temperature
If -40°C (-40°F), sensor circuit open
If 140°C (284°F), sensor circuit shorted
Intake Air
Intake air temperature
If -40°C (-40°F), sensor circuit open
If 140°C (284°F), sensor circuit shorted
Engine Run Time
Accumulated engine running time
-
Initial Engine Coolant Temp
Engine coolant temperature at engine start
-
Initial Intake Air Temp
Intake air temperature at engine start
-
Battery Voltage
Battery voltage
-
Accel Sens. No. 1 Volt %
Absolute Accelerator Pedal Position (APP) No. 1
-
Accel Sens. No. 2 Volt %
Absolute APP No. 2
-
Throttle Sensor Volt %
Throttle sensor positioning
-
Throttle Sensor #2 Volt %
Throttle sensor positioning #2
-
Throttle Sensor Position
Throttle position
-
Throttle Motor DUTY
Throttle motor
-
Injector (Port)
Injection period of No. 1 cylinder
-
Injection Volum (Cylinder1)
Injection volume
-
Fuel Pump/Speed Status
Fuel pump status
-
EVAP (Purge) VSV
EVAP purge VSV duty ratio
-
Evap Purge Flow
Ratio of evaporative purge flow to intake air volume
-
Purge Density Learn Value
Learning value of purge density
-
EVAP Purge VSV
EVAP Purge VSV
-
Target Air-Fuel Ratio
Ratio compared to stoichiometric level
-
AF Lambda B1S1
Fuel trim at A/F sensor
-
AFS Voltage B1S1
A/F sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
AFS Current B1S1
A/F sensor output current for sensor 1
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
O2S B1S2
Heated oxygen sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
Short FT #1
Short-term fuel trim
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
Long FT #1
Long-term fuel trim
Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central value
Total FT #1
Total fuel trim
-
Fuel System Status #1
Fuel system status #1
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  1. CL (Closed Loop): Using A/F sensor as feedback for fuel control
  1. OLDrive: Open loop due to driving conditions (fuel enrichment)
  1. OLFault: Open loop due to detected system fault
  1. CLFault: Closed loop but A/F sensor, used for fuel control malfunctioning
IGN Advance
Ignition advance
-
Knock Feedback Value
Feedback value of knocking
-
Knock Correct Learn Value
Correction learning value of knocking
-
VVT Control Status #1
VVT control status
-
Catalyst Temp (B1S1)
Estimated catalyst temperature (sensor 1)
-
Catalyst Temp (B1S2)
Estimated catalyst temperature (sensor 2)
-
Starter Signal
Starter switch (STSW) signal status
-
Starter Control
Starter control (STAR) signal
-
Power Steering Signal
Power steering signal
-
Starter Relay
Starter relay (STA) signal
-
Power Steer. Sig. Record
Power steering signal (history)
Signal status usually ON until ignition switch turned off
ACC Relay
ACC CUT relay status
-
Neutral Position SW Signal
Park/Neutral Position (PNP) switch signal status
-
Stop Light Switch
Stop light switch status
-
A/C Signal
A/C signal status
-
Closed Throttle Position SW
Closed throttle position switch
-
Fuel Cut Condition
Fuel cut condition
ON: Any fuel cut operation executed
Immobiliser Communication
Immobiliser communication
OFF: Communication malfunctioning, or engine immobiliser system set ON: Communication normal
Electrical Load Signal
Electrical load signal
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance from DTC cleared
-
Warm up Cycle Cleared DTC
Warm-up cycle after DTC cleared
-
TC and TE1
TC and CG (TE1) terminals of DLC3
-
Ignition Trig. Count
Ignition counter
-
Cylinder #1 Misfire Count
Cylinder #1 misfire count
-
Cylinder #2 Misfire Count
Cylinder #2 misfire count
-
Cylinder #3 Misfire Count
Cylinder #3 misfire count
-
Cylinder #4 Misfire Count
Cylinder #4 misfire count
-
All Cylinders Misfire Count
All cylinders misfire count
-
Misfire RPM
Engine speed when misfire occurred
-
Misfire Load
Engine load when misfire occurred
-
Misfire Margin
Margin to detect engine misfire
-
Catalyst OT MF F/C
Catalyst over temperature Misfire prevention fuel cut
-
Cat OT MF F/C History
Catalyst over temperature Misfire prevention fuel cut history:
-
Cat OT MF F/C Cylinder #1
Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder #2
Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder #3
Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder #4
Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)
-
Electric Fan Motor
Electric fan motor
-
Idle Fuel Cut
Fuel cut idle
ON: when throttle valve fully closed and engine speed over 3500 rpm
FC TAU
Fuel cut during very light load
Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete