COMPRESSOR (for Sedan) > INSTALLATION |
| 1. ADJUST COMPRESSOR OIL |
![]() |
When replacing the compressor with a new one, gradually discharge the refrigerant gas from the service valve. Then drain the following amount of oil from the new compressor before installation, so that the amount of oil contained in it is the same as that in the compressor to be replaced.
| 2. INSTALL COMPRESSOR AND PULLEY |
![]() |
Provisionally tighten the compressor with the bolt.
![]() |
Tighten the compressor with the 4 bolts.
Connect the connector.
| 3. INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE |
![]() |
Remove the attached vinyl tape from the hose.
Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the fitting surface of the compressor.
Install the O-ring onto the discharge hose.
Install the discharge hose onto the compressor with the bolt.
| 4. INSTALL NO. 1 COOLER REFRIGERANT SUCTION HOSE |
![]() |
Remove the attached vinyl tape from the hose.
Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the fitting surface of the compressor.
Install the O-ring onto the suction hose.
Install the suction hose onto the compressor with the bolt.
| 5. INSTALL FAN & GENERATOR V BELT |
Provisionally install the fan and generator V belt onto each pulley.
| 6. ADJUST FAN & GENERATOR V BELT |
![]() |
Insert an adjusting bar between the engine mounting bracket and generator assembly. Pull the adjusting bar toward the vehicle front to adjust the generator V belt tension .
| *a | OK |
| *b | NG |
![]() |
First tighten bolt A, then tighten bolt B.
| 7. INSPECT FAN & GENERATOR V BELT |
![]() |
Check the belt for wear, cracks or other signs of damage.
If any of the following defects is found, replace the V-ribbed belt.
![]() |
Check that the belt fits properly in the ribbed grooves.
| *a | CORRECT |
| *b | INCORRECT |
![]() |
Inspect the V belt deflection and tension.
| *A | w/o Air Conditioner |
| *B | w/ Air Conditioner |
| Item | Specified Condition |
| New belt | 8.0 to 9.0 mm (0.31 to 0.35 in) |
| Used belt | 12.5 to 13.5 mm (0.49 to 0.53 in) |
| Item | Specified Condition |
| New belt | 700 to 800 N (71 to 82 kg, 157 to 180 lb) |
| Used belt | 300 to 400 N (31 to 41 kg, 67 to 90 lb) |
| 8. INSTALL ENGINE UNDER COVER RH |
| 9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 10. CHARGE REFRIGERANT |

Perform vacuum purging using a vacuum pump.
Charge refrigerant HFC-134a (R134a).

Install the caps onto the service valves on the refrigerant line.
| 11. WARM UP ENGINE |
| 12. CHECK FOR REFRIGERANT LEAK |
After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.
Perform the operation as follows:
![]() |
Using the halogen leak detector, check the refrigerant line, especially the connection points, for leakage.
![]() |
Bring the halogen leak detector close to the drain hose before performing the test.
If a gas leak is not detected from the drain hose, remove the blower motor from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.
Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.