Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER (for Sedan)

FRONT SUSPENSION MEMBER (for Sedan) > REMOVAL

for Preparation Click here



1. POSITION FRONT WHEELS FACING STRAIGHT AHEAD


2. FIX STEERING WHEEL


    C232209
  1. Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.



3. REMOVE COLUMN HOLE COVER SILENCER SHEET


    C124831
  1. Fold back the floor carpet, and then remove the 2 clips and the column hole cover silencer sheet.



4. SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY


    C233394E01
  1. Place matchmarks on the steering sliding yoke sub-assembly and the steering gear assembly.
    Text in Illustration 
    *1
    Steering Sliding Yoke Sub-assembly
    *a
    Matchmark

  1. Loosen bolt A, remove bolt B and separate the steering sliding yoke sub-assembly from the steering gear assembly.



5. SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    C251207E01
  1. Remove clip A, separate clip B from the body and separate the No. 1 steering column hole cover sub-assembly.

    NOTICE:
    Do not damage clip B.



6. REMOVE FRONT WHEEL


7. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH


    C233131
  1. Remove the nut and separate the front stabilizer link assembly LH from the steering knuckle.

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 mm to hold the stud.



8. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.



9. SEPARATE TIE ROD END SUB-ASSEMBLY LH


    C265509
  1. Remove the cotter pin and the castle nut.



    C172757E03
  1. Install SST to the threaded section of the tie rod end sub-assembly LH.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure the upper ends of the threaded section of the tie rod end sub-assembly and SST are aligned.



  1. Using SST, separate the tie rod end sub-assembly from the front axle assembly.


    C249935E02


    Text in Illustration 
    *1
    Center Nut
    -
    -
    *a
    String
    *b
    Molybdenum Grease Application Area
    *c
    Place the wrench here
    *d
    Turn
    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. Apply molybdenum grease to the bolt threads and the tip of SST.
    2. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    3. Install SST so that A and B are parallel.
    4. Be sure to place the wrench on the part indicated in the illustration.
    5. Do not damage the ball joint dust cover.
    6. Do not damage the front disc brake dust cover.



10. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.



11. SEPARATE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH


    C107513
  1. Remove the clip and the castle nut.



    C172759E05
  1. Install SST to the threaded section of the lower ball joint.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure the upper ends of the threaded section of the lower ball joint and SST are aligned.



  1. Using SST, separate the lower arm.


    C265987E01


    Text in Illustration 
    *1
    Center Nut
    -
    -
    *a
    String
    *b
    Molybdenum Grease Application Area
    *c
    Place the wrench here
    *d
    Turn
    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. Apply molybdenum grease to the bolt threads and the tip of SST.
    2. Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
    3. Install SST so that A and B are parallel.
    4. Be sure to place the wrench on the part indicated in the illustration.
    5. Do not damage the lower ball joint dust cover.
    6. Do not damage the drive shaft outboard joint boots.
    7. Do not damage the front disc brake dust cover.



12. SEPARATE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.



13. SUPPORT ENGINE ASSEMBLY


    C234638
  1. Using a transmission jack and wooden block, support the engine assembly with transaxle.
    Text in Illustration 
    V100144
    Attachment Placement Position



14. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


    C213131
  1. Remove the bolt and separate the engine moving control rod.



    C233132
  1. Place wooden blocks or plate lift attachments in the positions shown in the illustration and set an engine lifter underneath the front suspension crossmember sub-assembly.
    Text in Illustration 
    V100135
    Front of the Vehicle
    V100144
    Attachment Placement Positions

    NOTICE:
    1. Place the wooden blocks or plate lift attachments so that the front suspension crossmember sub-assembly is level.
    2. As the front suspension crossmember sub-assembly is very heavy, be sure to support it securely.



    A246188
  1. Remove the 6 bolts and the front suspension crossmember sub-assembly.



15. REMOVE STEERING GEAR ASSEMBLY


C117189
  1. Remove the 2 bolts and 2 nuts and remove the steering gear assembly from the suspension crossmember.

    NOTICE:
    Keep the nut from rotating while turning the bolt.



16. REMOVE FRONT STABILIZER BRACKET LH


C116871
  1. Remove the 2 bolts and the stabilizer bracket.



17. REMOVE FRONT STABILIZER BRACKET RH

HINT:
Use the same procedure for the RH side as for the LH side.



18. REMOVE FRONT STABILIZER BAR


19. REMOVE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH


C107513
  1. Remove the clip and castle nut.



    C107514E01
  1. Using SST, separate the lower arm.

    SST
    09628-00011  

    NOTICE:
    1. Do not damage the lower arm dust cover.
    2. Suspend SST with a piece of string or the equivalent.



    C107515
  1. Remove the 2 bolts and lower arm.



20. REMOVE FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.



21. REMOVE ENGINE MOVING CONTROL ROD COVER (for Cold Area)
  1. Remove the 2 clips and the engine moving control rod cover.



22. REMOVE ENGINE MOVING CONTROL ROD


    C213122
  1. Remove the bolt and the engine moving control rod.