FRONT SEAT SIDE AIRBAG ASSEMBLY (for Hatchback Front Passenger Side) > DISPOSAL |
![]() |
| 1. DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (When Installed in Vehicle) |
![]() |
Check the function of SST.
![]() |
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
| *1 | Battery |
Press the SST activation switch, and check that the LED on the SST activation switch illuminates.
Disconnect SST from the battery.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the connector from the front seat side airbag assembly under the front seat assembly.
Push the slider with a finger to disengage the first claw. Without releasing your finger, slide the slider to disengage the second claw and disconnect the front seat side airbag connector.

| *1 | Slider | - | - |
| *a | Push | *b | Slide |
Connect SST.
![]() |
Connect the SST connector to the front seat side airbag assembly connector.
| *1 | Slider |
![]() |
Move SST at least 10 m (33 ft.) away from the front side window.
| *1 | Battery |
Maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
![]() |
Deploy the front seat side airbag.
| *1 | Plastic bag |
Check that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.
Press the SST activation switch and deploy the airbag.
| 2. DISPOSE OF FRONT SEAT SIDE AIRBAG ASSEMBLY (When not Installed in Vehicle) |
![]() |
Check the function of SST.
![]() |
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
| *1 | Battery |
Press the SST activation switch, and check that the LED on the SST activation switch illuminates.
Disconnect SST from the battery.
Remove the front seat side airbag assembly (Click here).
![]() |
Using braided wire harness, tie down the front seat side airbag assembly to an unneeded tire.
| *a | Stripped Wire Harness Section |
| Area | Measurement |
| A | 1.25 mm2 (0.0019 in.2) or more |
![]() |
Install the 2 nuts to the front seat side airbag assembly.
![]() |
Wind the wires around the stud bolts of the front seat side airbag assembly as shown in the illustration.
![]() |
Position the front seat side airbag assembly inside the tire.
| Area | Measurement |
| A | 185 mm (7.28 in.) |
| B | 360 mm (14.17 in.) |
Connect SST.
![]() |
Connect the SST connector to the front seat side airbag assembly connector.
![]() |
Place the tires.
| *1 | Tires (2 or more) |
Place at least 2 tires under the tire to which the front seat side airbag assembly is tied.
Place at least 2 tires onto the tire to which the front seat side airbag assembly is tied. The top tire should have a wheel installed.
![]() |
Tie the tires together with the 2 wires.
Connect SST.
![]() |
Connect the SST connector.
| *1 | Battery |
Move SST at least 10 m (33 ft.) away from the airbag tied down to the tire.
Deploy the airbag.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
Check that no one is within a 10 m (33 ft.) radius of the tire to which the front seat side airbag assembly is tied.
Press the SST activation switch and deploy the airbag.
![]() |
Dispose of the front seat side airbag assembly.
| *1 | Plastic bag |
Remove the front seat side airbag assembly from the tire.
Place the front seat side airbag assembly in a plastic bag, tie it tightly, and dispose of it according to local regulations.