Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS (for Hatchback)

BACK DOOR GLASS (for Hatchback) > REMOVAL



1. REMOVE REAR SPOILER SUB-ASSEMBLY (w/ Rear Spoiler)
(Click here)


2. REMOVE BACK DOOR TRIM BOARD


    B271631
  1. Disengage the 11 clips and remove the back door trim board.



3. REMOVE REAR WIPER ARM HEAD CAP (w/ Rear Wiper)


    B344502
  1. Disengage the 2 claws and the 2 hinges, to remove the rear wiper arm head cap.



4. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)


    E221587
  1. Remove the nut and the rear wiper arm and blade assembly.



5. REMOVE REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)


  1. for TMC Made:



      E221589E02
    1. Disconnect the connector.

    2. Remove the 2 bolts B.

    3. Loosen the bolt A to remove the rear wiper motor assembly.



  1. for TMMF Made:



      E221589
    1. Disconnect the connector.

    2. Remove the 3 bolts and the rear wiper motor assembly.



6. REMOVE REAR WIPER MOTOR GROMMET (w/ Rear Wiper)


    E263510
  1. Remove the rear wiper motor grommet.



7. REMOVE BACK DOOR PANEL NO. 2 PROTECTOR


    B271637E01
  1. Remove the 2 clips.
    Text in Illustration 
    *1
    Double-sided Tape

  1. While peeling off the double-sided tape, remove the back door panel No. 2 protector.



8. REMOVE BACK DOOR PANEL NO. 1 PROTECTOR

HINT:
Use the same procedure as for the No. 2 side.



9. REMOVE BACK DOOR GLASS


    B284408E01
  1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.
    Text in Illustration 
    *1
    Protective Tape



    B272677E01
  1. Place matchmarks on the back door glass and vehicle body on the locations indicated in the illustration.
    Text in Illustration 
    *a
    Mark

    HINT:
    Matchmarks are not necessary if the back door glass is not going to be reused.



    B272684
  1. Disconnect the 2 connectors.

    HINT:
    If the vehicle is equipped with rear window defogger, disconnect the connector.



    B272673E01
  1. Pass a piano wire between the vehicle body and glass from the interior.
    Text in Illustration 
    *1
    Piano Wire

  1. Tie both wire ends to wooden blocks or similar objects.

  1. Cut off the adhesive by pulling the piano wire around the back door glass.

    NOTICE:
    When separating the back door glass from the vehicle, be careful not to damage the paint or interior and exterior ornaments.



    B284409
  1. Using suction cups, disengage the 2 clips and remove the back door glass.

    NOTICE:
    Be careful not to drop the back door glass.



10. REMOVE BACK WINDOW GLASS ADHESIVE DAM
  1. Using a scraper, remove the back window glass adhesive dam.

    NOTICE:
    1. Be careful not to damage the back door glass.
    2. Be sure to replace the back window glass adhesive dam with a new one.



11. REMOVE BACK WINDOW GLASS CLIP LH
  1. Using a scraper, remove the back window glass clip.

    NOTICE:
    1. Be careful not to damage the back door glass.
    2. Be sure to replace the back window glass clip with a new one.



12. REMOVE BACK WINDOW GLASS CLIP RH
  1. Using a scraper, remove the back window glass clip.

    NOTICE:
    1. Be careful not to damage the back door glass.
    2. Be sure to replace the back window glass clip with a new one.