Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM (for Sedan)

SEAT BELT WARNING SYSTEM (for Sedan) > DATA LIST / ACTIVE TEST



READ DATA LIST

HINT:
Using a Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Turn the ignition switch OFF.

  2. Connect a Techstream to the DLC3.

  3. Turn the ignition switch to ON.

  4. Turn the tester ON.

  5. Enter the following menus: Body Electrical / (desired system) / Data List /

  6. According to the display on tester, read the "Data List".

    Center Airbag Sensor Assembly 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Driver Buckle SW
    Buckle switch (Driver side)/
    UNSET: Seat belt not fastened
    SET: Seat belt fastened
    NG: Data not determined
    UNSET/SET
    -
    Passenger Buckle SW
    Buckle switch (Passenger side)/
    UNSET: Seat belt not fastened
    SET: Seat belt fastened
    NG: Data not determined
    UNSET/SET
    -

    Occupant Classification ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Passenger Buckle SW
    Buckle switch (Front passenger side)/
    UNSET: Front passenger side seat belt is unfastened
    SET: Front passenger side seat belt is fastened
    NG: Front passenger side seat belt is malfunctioning
    UNSET/SET
    -
    Passenger Classification
    Front passenger classification/
    AF05: Adult (36 to 54 kg (79.37 to 119.05 lb)) is seated
    AM50: Adult more than 54 kg (119.05 lb) is seated
    CHILD: Child (less than 36 kg (79.37 lb)) is seated
    CRS: Child restraint system (less than 7 kg (15.43 lb)) and front passenger side buckle switch is ON, then 7 to 36 kg (15.43 to 79.37 lb) is set
    OFF: Vacant
    AF05/AM50/CHILD/CRS/OFF
    -

    Combination Meter Assembly 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P-Seatbelt Buckle SW
    Passenger seat belt buckle switch
    ON or OFF
    ON: Passenger seat belt is fastened
    OFF: Passenger seat belt is unfastened
    -


PERFORM ACTIVE TEST

HINT:
Using a Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Turn the ignition switch OFF.

  2. Connect a Techstream to the DLC3.

  3. Turn the ignition switch to ON.

  4. Turn the tester ON.

  5. Enter the following menus: Body Electrical / Combination Meter / Active Test /

  6. According to the display on tester, perform the "Active Test".

    Combination Meter Assembly 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Driver Side Seat Belt
    Front driver seat belt warning light
    OFF or ON
    -
    Front Passenger Side Seat Belt
    Front passenger seat belt warning light
    OFF or ON
    -