ANTI-LOCK BRAKE SYSTEM (for Hatchback) > TEST MODE PROCEDURE |
| WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK |
Release the parking brake.
When the ignition switch is turned to ON, check that the ABS warning and brake warning lights come on for approximately 3 seconds.
| Trouble Area | See Procedure |
| ABS warning light circuit (Remains on) |
Click here
|
| ABS warning light circuit (Does not come on) |
Click here
|
| Brake warning light circuit (Remains on) |
Click here
|
| Brake warning light circuit (Does not come on) |
Click here
|
| SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When Using Techstream) |
Procedure to enter Test Mode.
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position.
Check that the shift lever is in neutral and apply the parking brake.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Switch the skid control ECU (brake actuator assembly) to Test Mode using the Techstream.
Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Signal Check.
Check that the ABS warning light come on for several seconds and then blink in the Test Mode blinking pattern.
| Trouble Area | See Procedure |
| TS and CG terminal circuit |
Click here
|
| ABS warning light circuit (Remains on) |
Click here
|
| ABS warning light circuit (Does not come on) |
Click here
|
| SPEED SENSOR CHECK (When Using Techstream) |
Check the speed sensor signal.
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
| END OF SENSOR CHECK (When Using Techstream) |
If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle stops and the ABS warning light is off while the vehicle is being driven.
| READ DTC OF SIGNAL CHECK FUNCTION (When Using Techstream) |
Read the DTC(s) by following the tester screen.
List of DTCs.
| DTC Code | Detection Item | Trouble Area |
| C1271 | Low output signal from front speed sensor RH |
|
| C1272 | Low output signal from front speed sensor LH |
|
| C1273 | Low output signal from rear speed sensor RH |
|
| C1274 | Low output signal from rear speed sensor LH |
|
| C1275 | Abnormal change in output signal from front speed sensor RH | Speed sensor rotor |
| C1276 | Abnormal change in output signal from front speed sensor LH | Speed sensor rotor |
| C1277 | Abnormal change in output signal from rear speed sensor RH | Speed sensor rotor |
| C1278 | Abnormal change in output signal from rear speed sensor LH | Speed sensor rotor |
Turn the ignition switch off and disconnect the Techstream.
| SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When not Using Techstream) |
Procedure to enter Test Mode.
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position.
Check that the shift lever is in neutral and apply the parking brake.
![]() |
Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
| *a | Front view of DLC3 |
Turn the ignition switch to ON.
Check that the ABS warning light come on for several seconds and then blink in Test Mode.
| Trouble Area | See Procedure |
| TS and CG terminal circuit |
Click here
|
| ABS warning light circuit (Remains on) |
Click here
|
| ABS warning light circuit (Does not come on) |
Click here
|
| SPEED SENSOR CHECK (When not Using Techstream) |
Check the speed sensor signal.
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
| END OF SENSOR CHECK (When not Using Techstream) |
If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle stops and the ABS warning light is off while the vehicle is being driven.
| READ DTC OF SIGNAL CHECK FUNCTION (When not Using Techstream) |
![]() |
Using SST, connect terminals 12 (TS), 13 (TC) and 4 (CG) of the DLC3.
| *a | Front view of DLC3 |
Count the number of blinks of the ABS warning light.
After performing the check, disconnect SST from terminals TS and CG, and TC and CG of the DLC3 and turn the ignition switch off.
Turn the ignition switch to ON.
| DTC OF TEST MODE (SIGNAL CHECK) FUNCTION (Procedure "A") |
| DTC Code | Detection Item | Trouble Area |
| 71 | Low output signal from front speed sensor RH |
|
| 72 | Low output signal from front speed sensor LH |
|
| 73 | Low output signal from rear speed sensor RH |
|
| 74 | Low output signal from rear speed sensor LH |
|
| 75 | Abnormal change in output signal from front speed sensor RH | Speed sensor rotor |
| 76 | Abnormal change in output signal from front speed sensor LH | Speed sensor rotor |
| 77 | Abnormal change in output signal from rear speed sensor RH | Speed sensor rotor |
| 78 | Abnormal change in output signal from rear speed sensor LH | Speed sensor rotor |