VEHICLE STABILITY CONTROL SYSTEM (for Hatchback) > DTC CHECK / CLEAR |
| DTC CHECK/CLEAR (When Using Techstream) |
Check the DTC.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
Check the details of the DTCs (Click here).
Clear the DTC.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
Clear the DTCs by following the prompts on the Techstream.
| DTC CHECK/CLEAR (When not Using Techstream) |
![]() |
Check the DTC.
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the ignition switch to ON.
Observe the blinking pattern of the ABS warning and Slip indicator lights in order to identify the DTC.
| Trouble Area | See procedure |
| TC and CG terminal circuit |
Click here
|
| ABS warning light circuit (Remains on) |
Click here
|
| ABS warning light circuit (Does not come on) |
Click here
|
| Slip indicator light circuit (Remains on) |
Click here
|
| Slip indicator light circuit (Does not come on) |
Click here
|
| *a | Front view of DLC3 |
Check the details of the DTCs.
| Warning Light Display | Tester Display |
| 11 | C146E |
| 12 | C146F |
| 13 | C146C |
| 14 | C146D |
| 21 | C1468 |
| 22 | C1469 |
| 23 | C146A |
| 24 | C146B |
| 25 | C1225 |
| 31 | C1401 |
| C1405 | |
| 32 | C1402 |
| C1406 | |
| 33 | C1403 |
| C1407 | |
| 34 | C1404 |
| C1408 | |
| 35 | C1413 |
| 36 | C1414 |
| 38 | C1415 |
| 39 | C1416 |
| 41 | C1241 |
| C1417 | |
| 43 | C1243 |
| 44 | C1419 |
| C1442 | |
| 45 | C1245 |
| 46 | C1421 |
| C1422 | |
| C1423 | |
| C1424 | |
| 49 | C1425 |
| 51 | C1427 |
| C1428 | |
| 59 | C1203 |
| 91 | C1361 |
| 94 | U0073 |
| 95 | U0124 |
| 97 | C1381 |
| A2 | U0142 |
| Indicator Light Display | Tester Display |
| 31 | C1432 |
| C1433 | |
| C1434 | |
| 32 | C1232 |
| 34 | C1435 |
| C1436 | |
| C1443 | |
| 36 | C1210 |
| 39 | C1336 |
| 43*1 | - |
| 53 | C1203 |
| 63 | U0126 |
| 65 | C1437 |
| U0100 | |
| 66 | C1290 |
| C1439 | |
| C1445 | |
| 98 | C1440 |
After completing the check, disconnect terminals TC and CG of the DLC3 to turn off the display.
Clear the DTC.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the ignition switch to ON.
| *a | Front view of DLC3 |
Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.
Check that the warning light indicates a normal system code.
Remove SST from the terminals of the DLC3.
| END OF DTC CHECK/CLEAR |
Turn the ignition switch to ON.
Check that the ABS warning and Slip indicator lights go off within approximately 3 seconds after turning the ignition switch to ON.