Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (for Hatchback)

LIGHTING SYSTEM (for Hatchback) > Daytime Running Light Relay Circuit


DESCRIPTION

The main body ECU controls the daytime running lights (dimmed low beam headlights).

HINT:
  1. The running light relay has a headlight control function. This function dims the low beam headlights in accordance with operation signals from the main body ECU while the daytime running light system is operating.
  2. The running light relay dims the low beam headlights using a duty control.


WIRING DIAGRAM


E231964E03


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Daytime Running Light
    Running light relay
    OFF or ON
    -

    OK:
    Running light relay operates. (Daytime running lights illuminate.)



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK HEADLIGHT
  1. Check the operation of the low beam headlights.

    OK:
    Low beam headlights operate normally.



NG
GO TO PROBLEM SYMPTOMS TABLE (Click here)
OK


3.INSPECT RUNNING LIGHT RELAY


    E229351E01
  1. Remove the running light relay from the No. 2 engine room relay block.

  1. Connect a positive (+) lead from the battery to terminal 6 (+B).

  1. Connect a negative (-) lead from the battery to terminal 2 (DRLS) and 3 (E).

  1. Check for pulses according to the value(s) in the table below.

    OK:
    Tester Connection
    Condition
    Specified Condition
    1 (HLOR) - Battery negative terminal
    Always
    Pulse generation
    5 (HLOL) - Battery negative terminal
    Always
    Pulse generation

    Text in Illustration 
    *a
    Component without harness connected
    (Running Light Relay)



NG
REPLACE RUNNING LIGHT RELAY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (RUNNING LIGHT RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Remove the running light relay from the No. 2 engine room relay block assembly.

  1. Disconnect the 3C instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DRL-2 (DRLS) - 3C-22
    Always
    Below 1 Ω
    DRL-2 (DRLS) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly.

  1. Remove the main body ECU from the instrument panel junction block assembly.



  1. Measure the resistance according to the value(s) in the table below.


    E231963E03


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3C-22 - MB-25 (DRL)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

REPLACE MAIN BODY ECU (Click here)