POWER WINDOW CONTROL SYSTEM (for Sedan) > TERMINALS OF ECU |
| CHECK POWER WINDOW REGULATOR MASTER SWITCH |

Disconnect the G1 power window regulator master switch connector.
Measure the voltage and resistance of the wire harness side connector.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| G1-6 (B) - Body ground | GR - Body ground | Ignition power supply | Ignition switch OFF | Below 1 V |
| G1-6 (B) - Body ground | GR - Body ground | Ignition power supply | Ignition switch ON | 11 to 14 V |
| G1-1 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the G1 power window regulator master switch connector.
Measure the voltage of the connector.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| G1-3 (U) - G1-1 (E) | R- W-B | Power window motor UP output (driver side) | Ignition switch ON, driver side power window switch OFF → UP (manual operation) | Below 1 V → 11 to 14 V |
| G1-4 (D) - G1-1 (E) | G - W-B | Power window motor DOWN output (driver side) | Ignition switch ON, driver side power window switch OFF → DOWN (manual operation) | Below 1 V → 11 to 14 V |
| G1-4 (D) - G1-1 (E) | G - W-B | Power window motor DOWN output (driver side) | Ignition switch ON, driver side power window fully closed → driver side power window switch DOWN (AUTO operation) → driver side power window fully open | Below 1 V → 11 to 14 V → Below 1 V |
| G1-16 (U) - G1-1 (E) | W - W-B | Power window motor UP output (passenger side) | Ignition switch ON, passenger side power window switch OFF → UP | Below 1 V → 11 to 14 V |
| G1-15 (D) - G1-1 (E) | P - W-B | Power window motor DOWN output (passenger side) | Ignition switch ON, passenger side power window switch OFF → DOWN | Below 1 V → 11 to 14 V |
| G1-12 (U) - G1-1 (E) | Y - W-B | Power window motor UP output (rear LH) | Ignition switch ON, rear LH side power window switch OFF → UP | Below 1 V → 11 to 14 V |
| G1-13 (D) - G1-1 (E) | B - W-B | Power window motor DOWN output (rear LH) | Ignition switch ON, rear LH side power window switch OFF → DOWN | Below 1 V → 11 to 14 V |
| G1-10 (U) - G1-1 (E) | R - W-B | Power window motor UP output (rear RH) | Ignition switch ON, rear RH side power window switch OFF → UP | Below 1 V → 11 to 14 V |
| G1-18 (D) - G1-1 (E) | G - W-B | Power window motor DOWN output (rear RH) | Ignition switch ON, rear RH side power window switch OFF → DOWN | Below 1 V → 11 to 14 V |
Check the AUTO light illumination.
After turning the ignition switch ON, check that the AUTO light illuminates (green).
| CHECK POWER WINDOW SWITCH (PASSENGER SIDE) |

Disconnect the F1 power window switch connector.
Measure the voltage of the wire harness side connector.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| F1-3 (B) - Body ground | L - Body ground | Ignition power supply | Ignition switch OFF | Below 1 V |
| F1-3 (B) - Body ground | L - Body ground | Ignition power supply | Ignition switch ON | 11 to 14 V |
| F1-1 (D) - Body ground | G - Body ground | Power window motor DOWN output | Ignition switch ON, power window switch OFF → DOWN | Below 1 V → 11 to 14 V |
| F1-2 (SD) - Body ground | P - Body ground | Power window motor DOWN input (Remote) | Ignition switch ON, power window master switch OFF → DOWN (Remote) | Below 1 V → 11 to 14 V |
| F1-4 (U) - Body ground | R - Body ground | Power window motor UP output | Ignition switch ON, power window switch OFF → UP | Below 1 V → 11 to 14 V |
| F1-5 (SU) - Body ground | W - Body ground | Power window motor UP input (Remote) | Ignition switch ON, power window master switch OFF → UP (Remote) | Below 1 V → 11 to 14 V |
Reconnect the F1 power window switch connector.
| CHECK POWER WINDOW SWITCH (REAR DOOR SIDE) |

Disconnect the I1 and H1 power window switch connectors.
Measure the voltage of the wire harness side connector.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| 3 (B) - Body ground | SB - Body ground | Ignition power supply | Ignition switch OFF | Below 1 V |
| 3 (B) - Body ground | SB - Body ground | Ignition power supply | Ignition switch ON | 11 to 14 V |
| 4 (U) - Body ground | Y - Body ground | Power window motor UP output | Ignition switch ON, power window switch OFF → UP | Below 1 V → 11 to 14 V |
| 1 (D) - Body ground | B - Body ground | Power window motor DOWN output | Ignition switch ON, power window switch OFF → DOWN | Below 1 V → 11 to 14 V |
| 5 (SU) - Body ground | R - Body ground | Power window motor UP input (Remote) | Ignition switch ON, power window master switch OFF → UP (Remote) | Below 1 V → 11 to 14 V |
| 2 (SD) - Body ground | G - Body ground | Power window motor DOWN input (Remote) | Ignition switch ON, power window master switch OFF → DOWN (Remote) | Below 1 V → 11 to 14 V |
Reconnect the I1 and H1 power window switch connectors.