Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM (for Hatchback)

POWER WINDOW CONTROL SYSTEM (for Hatchback) > Rear Power Window LH does not Operate with Rear Power Window Switch LH


DESCRIPTION

If the rear LH side manual UP / DOWN function does not operate, a malfunction may exist in the rear power window regulator motor assembly LH, rear power window regulator switch assembly LH, power window regulator master switch assembly or wire harness.

WIRING DIAGRAM


B290898E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
  1. Inspect the rear power window regulator switch assembly LH (Click here).



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH (Click here)
OK


2.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
  1. Inspect the rear power window regulator motor assembly LH (Click here).



NG
REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - P/W RELAY)
B290899E02
  1. Disconnect the H10 rear power window regulator switch assembly LH connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H10-3 (B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Power Window Regulator Switch Assembly LH)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
  1. Disconnect the H10 rear power window regulator switch assembly LH connector.

  1. Disconnect the H11 rear power window regulator motor assembly LH connector.

  1. Measure the resistance according the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H10-4 (U) - H11-1 (U)
    Always
    Below 1 Ω
    H10-1 (D) - H11-2 (D)
    Always
    Below 1 Ω
    H10-4 (U) - Body ground
    Always
    10 kΩ or higher
    H10-1 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)
  1. Disconnect the H10 rear power window regulator switch assembly LH connector.

  1. Disconnect the G20 power window regulator master switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H10-5 (SU) - G20-12 (U)
    Always
    Below 1 Ω
    H10-2 (SD) - G20-13 (D)
    Always
    Below 1 Ω
    H10-5 (SU) - Body ground
    Always
    10 kΩ or higher
    H10-2 (SD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)