ENGINE IMMOBILISER SYSTEM (for Sedan) > TERMINALS OF ECU |
| CHECK TRANSPONDER KEY AMPLIFIER |

Disconnect the D24 transponder key amplifier connector.
Measure the resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| AGND (D24-7) - Body ground | GR - Body ground | Ground | Always | Below 1 Ω |
Reconnect the D24 transponder key amplifier connector.
Measure the resistance and voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| VC5 (D24-1) - AGND (D24-7) | P- GR | Power source | 1: No key in ignition key cylinder → 2: Key inserted | 1: 0 V → 2: 4.6 to 5.4 V |
| CODE (D24-4) - AGND (D24-7) | G- GR | Demodulated signal of key code data | No key in ignition key cylinder → Key inserted | Pulse generation (see waveform 1) |
| TXCT (D24-5) - AGND (D24-7) | V- GR | Key code output signal | 1: No key in ignition key cylinder → 2: Key inserted | Pulse generation (see waveform 2) |
| AGND (D24-7) - Body ground | GR- Body ground | Ground | Always | Below 1 Ω |
Inspect using an oscilloscope.
![]() |
Waveform 1
| Terminal | CODE (D24-4) - AGND (D24-7) |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | No key in ignition key cylinder → Key inserted |
![]() |
Waveform 2
| Terminal | TXCT (D24-5) - AGND (D24-7) |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | No key in ignition key cylinder → Key inserted |
| CHECK TRANSPONDER KEY ECU ASSEMBLY |

Disconnect the D23 transponder key ECU connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| GND (D23-16) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| +B (D23-1) - GND (D23-16) | L - W-B | Battery | Always | 11 to 14 V |
| IG (D23-2) - GND (D23-16) | R - W-B | Ignition switch | Ignition switch 1: OFF → 2: Key inserted | 1: 0 V → 2: 11 to 14 V |
Reconnect the D23 transponder key ECU connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| KSW (D23-3) - AGND (D23-5) | BE - GR | Unlock warning switch | 1: No key in ignition key cylinder → 2: Key inserted | 1: 11 to 14 V→ 2: Below 1 V |
| VC5 (D23-14) - AGND (D23-5) | P - GR | Power source | 1: No key in ignition key cylinder → 2: Key inserted | 1: 0 V → 2: 4.6 to 5.4 V |
| TXCT (D23-4) - AGND (D23-5) | V - GR | Transponder key amplifier communication signal | 1: No key in ignition key cylinder → 2: Key inserted | Pulse generation (see waveform 1) |
| CODE (D23-15) - AGND (D23-5) | G - GR | Transponder key amplifier communication signal | 1: No key in ignition key cylinder → 2: Key inserted | Pulse generation (see waveform 2) |
| EFIO (D23-13) - GND (D23-16) | W - W-B | ECM output signal | Ignition switch OFF → ON | Pulse generation (see waveform 3) |
| EFII (D23-12) - GND (D23-16) | BE - W-B | ECM input signal | Ignition switch OFF → ON | Pulse generation (see waveform 4) |
| CTY (D23-7) - GND (D23-16) | B - W-B | Courtesy signal | 1: Driver side door open → 2: closed | 1: 11 to 14 V → 2: Below 1 V |
| IND (D23-8) - GND (D23-16) | LG - W-B | Security indicator signal | Engine immobiliser system 1: SET → 2: UNSET | 1: 3 to 5 V → 2: Below 1 V |
| D (D23-9) - GND (D23-16) | W - W-B | Diagnosis tester communication | Ignition switch ON | Pulse generation |
Inspect using an oscilloscope.
![]() |
Waveform 1
| Terminal | TXCT (D23-4) - AGND (D23-5) |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch 1: No key in ignition key cylinder → 2: Key inserted |
![]() |
Waveform 2
| Terminal | CODE (D23-15) - AGND (D23-5) |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch 1: No key in ignition key cylinder → 2: Key inserted |
![]() |
Waveform 3
| Terminal | EFIO (D23-13) - GND (D23-16) |
| Tool Setting | 10 V/DIV., 500 ms/DIV. |
| Condition | Ignition switch OFF → ON |
![]() |
Waveform 4
| Terminal | EFII (D23-12) - GND (D23-16) |
| Tool Setting | 10 V/DIV., 500 ms/DIV. |
| Condition | Ignition switch OFF → ON |
Measure the resistance between each pair of connector terminal.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| AGND (D23-5) - GND (D23-16) | GR - W-B | Amplifier ground circuit | Always | Below 1 Ω |
| CHECK ECM |

Disconnect the A21 ECM connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| IMI (A21-11) - E1 (C20-104) | W - W | Transponder key ECU input signal | Ignition switch off | Below 1 V |
| Ignition switch on | Pulse generation (see waveform 1) | |||
| IMO (A21-10) - E1 (C20-104) | BE - W | Transponder key ECU output signal | Ignition switch off | 11 to 14 V |
| Within 3 seconds after starter operates and initial combustion occurs, or within 3seconds after ignition switch first turned on (IG) after battery disconnected and connected. | Pulse generation (see waveform 2) | |||
| E1 (C20-104) - Body ground | W - Body ground | Ground | Always | Below 1 Ω |
Reconnect the A21 ECU connector.
Inspect using an oscilloscope.
![]() |
Waveform 1
| Terminal | IMI (A21-11) - E1 (C20-104) |
| Tool Setting | 10 V/DIV., 500 ms/DIV. |
| Condition | Ignition switch on |
![]() |
Waveform 2
| Terminal | IMO (A21-10) - E1 (C20-104) |
| Tool Setting | 5 V/DIV., 500 ms/DIV. |
| Condition | Within 3 seconds after starter operates and initial combustion occurs, or within 3seconds after ignition switch first turned on (IG) after battery disconnected and connected. |