ENGINE IMMOBILISER SYSTEM (for Sedan) > REGISTRATION |
| 1. DESCRIPTION OF CODE REGISTRATION |
When adding master keys and sub-keys (additional registration).
Register the key codes in the transponder key ECU.
| Target ECU | See Procedure |
| Transponder key ECU | Procedure "A" |
After replacing the transponder key ECU (new key code registration).
Register the key codes (immobiliser codes) in the new transponder key ECU.
| Target ECU | See Procedure |
| Transponder key ECU | Procedure "B" |
Register the ECM COMMUNICATION ID for communication between the ECM and the new transponder key ECU.
| Target ECU | See Procedure |
| ECM | Procedure "C" |
After replacing the ECM.
Register the ECU COMMUNICATION ID for communication between the new ECM and the transponder key ECU.
| Target ECU | See Procedure |
| Transponder key ECU | Procedure "C" |
After replacing the transponder key ECU and ECM.
Register the ECU COMMUNICATION ID for communication between the new ECM and the new transponder key ECU.
| Target ECU | See Procedure |
| Transponder key ECU | Procedure "C" |
Erasure of key codes.
Erase the key code(s) of the lost key(s).
| Target ECU | See Procedure |
| Transponder key ECU | Procedure "D" |
| 2. NEW KEY CODE REGISTRATION (PROCEDURE "B") |
New key code registration (When using Techstream).
| Procedure | Security Indicator Condition |
| 1. START | -
|
| 2. Insert the key into the ignition key cylinder. | BLINKING |
| 3. Select the following items on the tester: (1) Body Electrical (2) Immobiliser (3) ID Utility (4) Immobiliser Code Registration
| ON
|
| OFF for 1 second and then ON | |
| 4. Remove the key and then push the NEXT button on the tester. | ON |
| 5. Insert a master key or sub-key to be registered. | OFF for 1 second and then ON |
| 6. Remove the key and then push the NEXT button on the tester. | ON |
| 7. Insert a master key or sub-key to be registered. | OFF for 1 second and then ON |
OFF
| |
| 8. Remove the key. | BLINKING |
| 9. END | |

New key code registration (Without using Techstream)
| Procedure | Time (Operation completion time) | Security Indicator Condition |
| 1. START | - | -
|
| 2. Insert a previously registered key into the ignition key cylinder. Remove and insert it again. Repeat this 4 times. | Within 35 seconds | BLINKING |
| 3. Open and close the driver door 6 times. | ||
| 4. Remove the key. | ON | |
| 5. Insert the master key to be registered into the ignition key cylinder. | Within 10 seconds | BLINKING |
6. After 60 seconds, the key is registered.
| - | |
| 7. Remove the key. | BLINKING | |
| 8. END | ||
| 3. REGISTRATION OF ADDITIONAL KEY (PROCEDURE "A") |
Additional key code registration
| Procedure | Time (Operation completion time) | Security Indicator Condition |
| 1. START | - | BLINKING
|
| 2. Insert a previously registered master key into the ignition key cylinder, turn the ignition switch to the ON position, and turn the Techstream on. | - | OFF |
| 3. Select the following items on the tester: (1) Body Electrical (2) Immobiliser (3) ID Utility (4) Immobiliser Code Registration | ON | |
| 4. Remove the master key and then push the NEXT button on the tester. Immediately after above operation insert a previously registered master key into the ignition key cylinder, turn the ignition switch to the ON position, and then push the NEXT button on the tester. | Within 120 seconds | BLINKING→ON |
| 5. Remove the master key and then push the NEXT button on the tester. | Within 20 seconds
| ON |
| 6. Insert the key to be registered into the ignition key cylinder. | Within 10 seconds. | BLINKING |
7. After 60 seconds, the key is registered.
| - | OFF |
| 8. Remove the key and then push the NEXT button on the tester. | BLINKING | |
| 9. The tester screen displays the number of registered keys. | ||
| 10. END | ||
| 4. ERASURE OF KEY CODE (PROCEDURE "D") |
Erasure of key code
| Procedure | Time (Operation completion time) | Security Indicator Condition |
| 1. START | - | BLINKING
|
| 2. Insert a previously registered master key into the ignition key cylinder, turn the ignition switch to the ON position, and turn the Techstream on. | - | OFF |
| 3. Select the following items on the tester: (1) Body Electrical (2) Immobiliser (3) ID Utility (4) Immobiliser Code Registration | OFF | |
| 4. Remove the key and then push the NEXT button on the tester. Immediately after the above operation insert a previously registered master key into the ignition key cylinder, turn the ignition switch to the ON position, and then push the NEXT button on the tester. | Within 120 seconds | BLINKING→ ON for 1 second then OFF. |
| 5. Remove the master key. | Within 10 seconds
| BLINKING |
| 6. END | ||
| 5. ECU - ECM COMMUNICATION ID REGISTRATION (PROCEDURE "C") |
After replacing the transponder key ECU
Register the key code(s) by following the new key code registration procedure. (Procedure "B")
Using SST, connect the TC and CG terminals of the DLC3 before inserting the key into the key cylinder.

Insert a previously registered key into the ignition key cylinder, turn the ignition switch to ON (do not start the engine), and leave it as is for 30 minutes.
Turn the ignition switch to OFF and disconnect terminals TC and CG.
Start the engine.
Check that the engine starts and stays on for more then 3 seconds. The registration is complete.
After replacing the ECM.
Register the ECU - ECM communication ID
| Procedure | Security Indicator Condition |
| 1. Insert a previously registered key into the ignition key cylinder. | OFF |
| 2. Start the engine. | |
| 3. Check that the engine starts and stays on for more than 3 seconds. The registration is complete. |
After replacing the transponder key ECU and ECM
Register the key code(s) by following the new key code registration procedure. (Procedure "B")
Register the ECU - ECM communication ID
| Procedure | Security Indicator Condition |
| 1. Insert a previously registered key into the ignition key cylinder. | OFF |
| 2. Start the engine. | |
| 3. Check that the engine starts and stays on for more than 3 seconds. The registration is complete. |