THEFT DETERRENT SYSTEM (for Sedan) > SYSTEM DESCRIPTION |
| OUTLINE OF THEFT DETERRENT SYSTEM |
When any attempt is made to forcibly enter the vehicle, open the engine hood or unlock any door without using a key, or when the battery terminals are disconnected and then reconnected, this system causes the vehicle horn and security horn to sound, the interior light to light up, and the hazard warning lights, taillights and headlights to flash, in order to deter break-in and theft.
The theft deterrent system has two arming modes; Active and Passive. Active arming mode allows the theft deterrent system to activate normally. Passive arming mode is used for the servicing. The Techstream allows the theft deterrent system to switch between Active and Passive.
(Click here)
Each mode has 4 states; a disarmed state, an arming preparation state, an armed state and an alarm sounding state.
Disarmed state:
Arming preparation state:
Armed state:
Alarm sounding state:
| Alarm Form | Headlight | Blinks (approximately 0.4 seconds cycles) |
| Taillight | Blinks (approximately 0.4 seconds cycles) | |
| Hazard Warning Light | Blinks (Cycle of flasher relay) | |
| Interior Light | Illuminates | |
| Vehicle Horn | Sounds (approximately 0.4 seconds cycles) | |
| Security Horn | Sounds (approximately 0.4 seconds cycles) | |
| Alarm Duration | Approximately 57 seconds | |
| ACTIVE ARMING MODE |
Active arming mode

| Condition | Item |
| Condition (1) | (No key in ignition key cylinder)
|
| Condition (2) |
|
| Condition (3) | One of following operations performed within 30 seconds of entering arming preparation state:
|
| Condition (4) | One of following operations performed in armed state:
|
| Condition (5) | One of following operations performed in alarm sounding state or armed state:
|
| Condition (6) |
|
| PASSIVE ARMING MODE |
Passive arming mode

| Condition | Item |
| Condition (1) |
|
| Condition (2) |
|
| Condition (3) | One of following operations performed in arming preparation state or disarmed state (2):
|
| Condition (4) |
|
| Condition (5) |
|
| Condition (6) | One of following operations performed in armed state:
|
| Condition (7) | One of following operations performed in armed state or alarm sounding state:
|
| Condition (8) |
|
| Condition (9) |
|
| ALARM MEMORY FUNCTION |
If the alarm is set off (tampering is detected) while the theft deterrent system is armed, the alarm memory function records it. Whenever the theft deterrent system is canceled, the alarm memory function causes the taillights to light up for 2 seconds in order to indicate that the alarm has been set off.
Conditions of the alarm memory function that cause the taillights to light up:
When the theft deterrent system has entered the alarm sounding state (tampering has been detected), the taillights light up for 2 seconds if either of the following conditions is met.
| SECURITY INDICATOR OUTPUT |
The theft warning ECU outputs a signal to light up the security indicator, according to the state of the theft deterrent system. However, some of the actual lighting conditions of the security indicator are different from the output signals of the theft warning ECU.
| Theft Deterrent System Condition* | Security Indicator | |
| Output Signals from Theft Warning ECU | Actual Lighting Condition | |
| Disarmed state (1), (2) | OFF | OFF (immobiliser system unset) BLINKING (immobiliser system set) |
| Arming preparation state | ON | ON |
| Armed state (During entry delay time) | BLINKING (ON) | BLINKING (ON) |
| Alarm sounding state | ON | ON |
| Time | Security Indicator |
| 0.2 seconds | ON |
| 1.8 seconds | OFF |
| ENTRY DELAY FUNCTION |
When any door is opened while all the doors are closed during passive arming mode, the entry delay time starts. If the switch condition (7) or (8) (see PASSIVE ARMING MODE) is met during the entry delay time, the theft deterrent system will not set off the alarm. However, if the switch condition (7) or (8) is not met, the theft deterrent system will recognize it as a theft and set off the alarm.
