POWER WINDOW CONTROL SYSTEM (for Hatchback) > TERMINALS OF ECU |
| POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY |

Disconnect the G20 power window regulator master switch assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| G20-6 (B) - G20-1 (E) | GR - W-B | Power supply | Ignition switch ON | 11 to 14 V |
| G20-1 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| G20-15 (B) - G20-7 (E) | GR - W-B | Power supply | Ignition switch ON | 11 to 14 V |
| G20-7 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the power window regulator master switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| G20-3 (U) - G20-1 (E) | LA-R - W-B | Power window motor UP operation | Ignition switch ON, driver door power window switch OFF → UP | 11 to 14 V → Below 1 V |
| G20-4 (D) - G20-1 (E) | LA-G - W-B | Power window motor DOWN operation | Ignition switch ON, driver door power window switch OFF → DOWN (Manual operation) | 11 to 14 V → Below 1 V |
| Power window motor AUTO DOWN operation | Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened | 11 to 14 V → Below 1 V → 11 to 14 V |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| G20-10 (U) - G20-7 (E) | LA-R - W-B | Power window motor UP operation | Ignition switch ON, driver door power window switch OFF → UP (Manual operation) | 11 to 14 V → Below 1 V |
| G20-12 (D) - G20-7 (E) | LA-G - W-B | Power window motor DOWN operation | Ignition switch ON, driver door power window switch OFF → DOWN (Manual operation) | 11 to 14 V → Below 1 V |
| Power window motor AUTO DOWN operation | Ignition switch ON, driver side door glass fully closed → driver side power window AUTO DOWN operation → driver side door glass fully opened | 11 to 14 V → Below 1 V → 11 to 14 V |
| CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (FRONT PASSENGER SIDE) |

Disconnect the F20 power window regulator switch assembly (front passenger side) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| F20-3 (B) - Body ground | L - Body ground | Power supply | Ignition switch ON | 11 to 14 V |
| F20-5 (SU) - Body ground | W - Body ground | Ground | Always | Below 1 Ω |
| F20-2 (SD) - Body ground | P - Body ground | Ground | Always | Below 1 Ω |
Reconnect the F20 power window regulator switch assembly (front passenger side) connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| F20-4 (U) - Body ground | LA-R - Body ground | Power window motor UP operation | Front passenger side power window switch OFF → UP | Below 1 V → 11 to 14 V |
| F20-1 (D) - Body ground | LA-G - Body ground | Power window motor DOWN operation | Front passenger side power window switch OFF → DOWN | Below 1 V → 11 to 14 V |
| CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH |

Disconnect the H10 rear power window regulator switch assembly LH connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| H10-3 (B) - Body ground | LA-SB - Body ground | Power supply | Ignition switch ON | 11 to 14 V |
| H10-5 (SU) - Body ground | LA-R - Body ground | Ground | Always | Below 1 Ω |
| H10-2 (SD) - Body ground | LA-G - Body ground | Ground | Always | Below 1 Ω |
Reconnect the H10 rear power window regulator switch assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| H10-4 (U) - Body ground | LA-Y - Body ground | Power window motor UP operation | Front passenger side power window switch OFF → UP | Below 1 V → 11 to 14 V |
| H10-1 (D) - Body ground | LA-B - Body ground | Power window motor DOWN operation | Front passenger side power window switch OFF → DOWN | Below 1 V → 11 to 14 V |
| CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH |

Disconnect the R1 rear power window regulator switch assembly RH connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| R1-3 (B) - Body ground | LA-SB - Body ground | Power supply | Ignition switch ON | 11 to 14 V |
| R1-5 (SU) - Body ground | LA-R - Body ground | Ground | Always | Below 1 Ω |
| R1-2 (SD) - Body ground | LA-G - Body ground | Ground | Always | Below 1 Ω |
Reconnect the R1 rear power window regulator switch assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| R1-4 (U) - Body ground | LA-Y - Body ground | Power window motor UP operation | Front passenger side power window switch OFF → UP | Below 1 V → 11 to 14 V |
| R1-1 (D) - Body ground | LA-B - Body ground | Power window motor DOWN operation | Front passenger side power window switch OFF → DOWN | Below 1 V → 11 to 14 V |
| CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU |

| *A | Main Body ECU 1 Connector Type | - | - |
| *1 | Instrument Panel Junction Block Assembly | *2 | Main Body ECU |

| *A | Main Body ECU 2 Connector Type | - | - |
| *1 | Instrument Panel Junction Block Assembly | *2 | Main Body ECU |
Remove the main body ECU.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| MB-11 (GND1) - Body ground | - | Ground | Always | Below 1 Ω |
| MB-29 (ACC) - Body ground | - | Ignition power supply (ACC signal) | Ignition switch ACC | 11 to 14 V |
| MB-30 (BECU) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| MB-32 (IG) - Body ground | - | Ignition power supply (IG signal) | Ignition switch ON | 11 to 14 V |
Reinstall the main body ECU.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| D143-2 (KOFF) - Body ground | L - Body ground | Power window relay operation signal | Ignition switch ON | 11 to 14 V |
| Approximately 45 seconds after ignition switch turned off | Below 1 V | |||
| D143-19 (FRCY) - Body ground | Y - Body ground | Front door courtesy light switch RH signal | Front door RH opened | Below 1 V |
| Front door RH closed | Pulse generation | |||
| 3D-36 (FLCY) - Body ground | L - Body ground | Front door courtesy light switch LH signal | Front door LH opened | Below 1 V |
| Front door LH closed | Pulse generation |