Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM (for Hatchback)

DTC    B1793    Occupant Classification Sensor Power Supply Circuit Malfunction


DESCRIPTION

The occupant classification sensor power supply circuit consists of the occupant classification ECU and the occupant classification sensors.
DTC B1793 is stored when a malfunction is detected in the occupant classification sensor power supply circuit.

DTC Code
DTC Detection Condition
Trouble Area
B1793
One of following conditions is met:
  1. Occupant classification ECU receives line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in occupant classification sensor power supply circuit for 2 seconds
  2. Open circuit in occupant classification sensor wire harness
  3. Occupant classification ECU malfunction
  1. Separate type front seat cushion pad RH (Rear occupant classification sensors)
  2. Front seat wire RH

HINT:
  1. When DTC B1650/32 is detected as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1793 of the occupant classification system.
  2. Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTCs cannot be read.


WIRING DIAGRAM


C243263E02


INSPECTION PROCEDURE

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the front seat assembly RH installation bolts to see the undersurface of the seat cushion.
  2. In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.

1.CHECK FOR DTC
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

    HINT:
    1. First clear DTCs stored in the occupant classification ECU and then in the airbag sensor assembly.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1793 is not output.

    HINT:
    DTCs other than DTC B1793 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK CONNECTION OF CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU and the occupant classification sensors.

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3.CHECK CONNECTOR
  1. Check that the connectors (on the occupant classification ECU side and the occupant classification sensors side) are not damaged.

    OK:
    Connectors are not deformed or damaged.



NG
REPLACE FRONT SEAT WIRE RH (Click here)
OK


4.CHECK FRONT SEAT WIRE RH


  1. Disconnect the connectors from the occupant classification ECU and the 2 occupant classification sensors.


    C243264E02


    Text in Illustration 
    *1
    Occupant Classification Sensor
    *2
    Occupant Classification ECU
    *3
    Front Seat Wire RH
    -
    -
    *a
    Front view of wire harness connector
    (to Occupant Classification ECU)
    *b
    Front view of wire harness connector
    (to Rear Occupant Classification Sensor LH)
    *c
    Front view of wire harness connector
    (to Rear Occupant Classification Sensor RH)
    *d
    Connector B
    *e
    Connector C
    -
    -

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    X3-1 - Body ground
    Ignition switch ON
    Below 1 V
    X3-2 - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    X3-1 - X2-1
    Always
    Below 1 Ω
    X3-2 - X1-1
    X3-1 - Body ground
    Always
    1 MΩ or higher
    X3-2 - Body ground
    X3-1 - X3-2



NG
REPLACE FRONT SEAT WIRE RH (Click here)
OK


5.CHECK FOR DTC
  1. Connect the connectors to the occupant classification ECU and the 2 occupant classification sensors.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

    HINT:
    1. First clear DTCs stored in the occupant classification ECU and then in the airbag sensor assembly.
    2. Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the Techstream, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1793 is not output.

HINT:
DTCs other than DTC B1793 may be output at this time, but they are not related to this check.



NG
Go to step 6
OK

USE SIMULATION METHOD TO CHECK (Click here)  

6.REPLACE SEPARATE TYPE FRONT SEAT CUSHION PAD RH
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the separate type front seat cushion pad RH (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.


NEXT


7.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).


NEXT

END