Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE (for Hatchback)

NAME PLATE (for Hatchback) > INSTALLATION



1. INSTALL NO. 4 BACK DOOR NAME PLATE


  1. for Type A:

    1. Clean the attachment surface.

      1. Using an infrared light, heat the double-sided tape remaining on the back door panel.

        Heating Temperature:
        Item
        Temperature
        Back Door Panel
        40 to 60°C (104 to 140°F)

        CAUTION:
        Do not burn yourself on the hot body panel or with the infrared light.

        NOTICE:
        Do not heat the back door panel excessively.

      2. Using a piece of cloth, rub the double-sided tape off the back door panel while it is hot from the infrared light.

        NOTICE:
        Installing the No. 4 back door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

      3. Using a non-residue solvent, clean the attachment surface.



    2. Install a new No. 4 back door name plate as shown in the illustration.


      B332225E01

      Installation Position:
      Mark
      Measurement (along surface)
      A
      259.6 mm (10.2 in.)
      B
      250.4 mm (9.86 in.)
      C
      106.3 mm (4.18 in.)

      NOTICE:
      Install the No. 4 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 4 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 4 back door name plate.



  1. for Type B:

    1. Clean the attachment surface.

      1. Using an infrared light, heat the double-sided tape remaining on the back door panel.

        Heating Temperature:
        Item
        Temperature
        Back Door Panel
        40 to 60°C (104 to 140°F)

        CAUTION:
        Do not burn yourself on the hot body panel or with the infrared light.

        NOTICE:
        Do not heat the back door panel excessively.

      2. Using a piece of cloth, rub the double-sided tape off the back door panel while it is hot from the infrared light.

        NOTICE:
        Installing the No. 4 back door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

      3. Using a non-residue solvent, clean the attachment surface.



    2. Install a new No. 4 back door name plate as shown in the illustration.


      B332224E01

      Installation Position:
      Mark
      Measurement (along surface)
      A
      259.8 mm (10.2 in.)
      B
      250.4 mm (9.86 in.)
      C
      103.7 mm (4.08 in.)

      NOTICE:
      Install the No. 4 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 4 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 4 back door name plate.



2. INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided tape remaining on the back door panel.

      Heating Temperature:
      Item
      Temperature
      Back Door Panel
      40 to 60°C (104 to 140°F)

      CAUTION:
      Do not burn yourself on the hot body panel or with the infrared light.

      NOTICE:
      Do not heat the back door panel excessively.

    2. Using a piece of cloth, rub the double-sided tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 2 luggage compartment door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.



  1. Install a new No. 2 luggage compartment door name plate as shown in the illustration.


    B283006E05

    Installation Position:
    Mark
    Measurement (along surface)
    A
    223.8 mm (8.81 in.)
    B
    211.9 mm (8.34 in.)
    C
    167.1 mm (6.58 in.)

    NOTICE:
    Install the No. 2 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 2 luggage compartment door name plate to 20 to 30°C (68 to 86°F) and install the No. 2 luggage compartment door name plate.



3. INSTALL SYMBOL EMBLEM
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided tape remaining on the back door panel.

      Heating Temperature:
      Item
      Temperature
      Back Door Panel
      40 to 60°C (104 to 140°F)

      CAUTION:
      Do not burn yourself on the hot body panel or with the infrared light.

      NOTICE:
      Do not heat the back door panel excessively.

    2. Using a piece of cloth, rub the remaining double-sided tape off the back door panel while it is hot from the infrared light.

      NOTICE:
      Installing the symbol emblem with any double-sided tape remaining on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.



    B283004E02
  1. Insert the 2 location pins into the back door panel and install a new symbol emblem.
    Text in Illustration 
    *a
    Location Pin

    NOTICE:
    Install the symbol emblem in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the symbol emblem to 20 to 30°C (68 to 86°F) and install the symbol emblem.