Home › Drivetrain ยท U340E AUTOMATIC TRANSMISSION / TRANSAXLE › TRANSMISSION WIRE (for Sedan)

TRANSMISSION WIRE (for Sedan) > INSTALLATION



1. INSTALL TRANSMISSION WIRE


C067760
  1. Coat a new O-ring with Toyota Genuine ATF WS or equivalent and install it into the transmission wire.



    D025102
  1. Pass the transmission wire through the transaxle.



    C062929
  1. Install the transmission wire with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



2. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


D005902E01
  1. Coat 2 new apply gaskets with Toyota Genuine ATF WS or equivalent and install them into the transaxle case.



    D005901E01
  1. Install the check ball body spring and check ball body.



    C093940E11
  1. Align the groove of the manual valve with the pin of the manual valve lever.

  1. Provisionally install the valve body with the 13 bolts.

    Bolt length:
    Bolt A:
    32 mm (1.26 in.)
    Bolt B:
    22 mm (0.87 in.)
    Bolt C:
    55 mm (2.17 in.)
    Bolt D:
    45 mm (1.77 in.)



    C093939E08
  1. Provisionally install the detent spring and detent spring cover with the 2 bolts.

    Bolt length:
    Bolt A:
    14 mm (0.55 in.)
    Bolt B:
    45 mm (1.77 in.)

  1. Check that the manual valve lever comes into contact with the center of the roller at the tip of the detente spring.

  1. Tighten the 15 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }



    C093938E05
  1. Install the ATF temperature sensor with the lock plate and bolt.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Connect the 5 shift solenoid valve connectors.



3. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


D005904E04
  1. Coat a new oil strainer gasket with Toyota Genuine ATF WS or equivalent, and install it into the oil strainer.



    C062685E02
  1. Install the oil strainer with the 3 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }



4. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


C093943E02
  1. Install the 2 magnets onto the oil pan, as shown in the illustration.



    D008009E01
  1. Install the oil pan and a new gasket with the 19 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }



5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



6. ADD AUTOMATIC TRANSAXLE FLUID
Automatic Transaxle Fluid 
Classification
Capacity (Reference)
Toyota Genuine ATF WS or equivalent
Dry fill
6.4 liters (6.8 US qts, 5.6 Imp. qts)
Drain and refill
2.5 liters (2.6 US qts, 2.2 Imp. qts)


7. INSPECT AUTOMATIC TRANSAXLE FLUID


D025120E03

HINT:
Drive the vehicle until the engine and transaxle are at normal operating temperature.

Fluid temperature:
70 to 80 °C (158 to 176 °F)

  1. Park the vehicle on a level surface and engage the parking brake.

  1. With the engine idling and the brake pedal depressed, shift the shift lever into all positions from P to L, and then return it to the P position.

  1. Pull out the oil level gauge and wipe it clean.

  1. Push it fully back into the pipe.

  1. Pull it out and check that the fluid level is within the HOT range.
    If there is any leakage, repair or replace O-rings, FIPGs, oil seals, plugs or other parts.



8. CHECK FOR AUTOMATIC TRANSAXLE FLUID LEAKAGE


9. INSTALL ENGINE UNDER COVER LH