Home › Drivetrain ยท U340E AUTOMATIC TRANSMISSION / TRANSAXLE › TRANSMISSION CONTROL CABLE (for Hatchback)

TRANSMISSION CONTROL CABLE (for Hatchback) > INSTALLATION



1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY


    C159381E03
  1. Connect the transmission control cable assembly to the control shaft lever with the nut.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Transmission Control Cable Bracket
    *2
    Clip
    *a
    Marking

  1. Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.

    NOTICE:
    Make sure that the marking on the cable is aligned with the slit in the No. 1 transmission control cable bracket before installing the cable.

  1. Install the transmission control cable assembly to the control cable support.

  1. Install the transmission control cable assembly with the 3 nuts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



2. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR
  1. Install the front No. 1 floor heat insulator with the 2 bolts and nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



3. INSTALL FRONT EXHAUST PIPE ASSEMBLY
(Click here)


4. INSTALL AIR CLEANER BRACKET
  1. Install the air cleaner bracket with the 2 bolts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }

  1. Engage the clamp and connect the wire harness to the air cleaner bracket.



5. INSTALL AIR CLEANER ASSEMBLY
  1. Install the air cleaner case onto the air cleaner bracket with the 2 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

  1. Engage the clamp and connect the wire harness to the air cleaner case.

  1. Install the air cleaner element onto the air cleaner case.

  1. Install the air cleaner cap sub-assembly with No. 1 air cleaner hose onto the throttle body assembly

  1. Engage the 2 clamps and connect the air cleaner cap sub-assembly to the air cleaner case sub-assembly.

  1. Tighten the hose clamp.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }

  1. Connect the vacuum switching valve assembly connector.

  1. Connect the mass air flow meter connector.

  1. Engage the 2 clamps and connect the wire harness to the air cleaner cap sub-assembly and vacuum switching valve assembly.

  1. Connect the No. 2 fuel vapor feed hose to the intake manifold.

  1. Connect the fuel vapor feed hose assembly to the No. 1 air cleaner hose and vacuum switching valve assembly with the 2 hose clamps.

  1. Engage the clamp and connect the fuel vapor feed hose assembly to the No. 1 air cleaner hose.



6. INSTALL BATTERY CARRIER
  1. Install the battery carrier with the 5 bolts.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Engage the 6 clamps and connect the wire harness to the battery carrier.



7. INSTALL BATTERY TRAY


8. INSTALL BATTERY
  1. Install the battery onto the battery tray with the battery clamp.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }

  1. Connect the cable to the battery terminal.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



9. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    C195134E04
  1. Rotate the nut of the transmission control cable assembly approximately 180° in the direction shown in the illustration, and while holding the nut, push in the lock.
    Text in Illustration 
    *1
    Nut
    *2
    Lock
    *a
    Rotate approximately 180°
    *b
    Push in

    NOTICE:
    Rotating the nut too much will damage the internal spring, and the transmission control cable assembly will not be reusable. Do not turn the nut too far.



    C271865E01
  1. Install the transmission control cable assembly to the shift lever assembly.
    Text in Illustration 
    *1
    Protrusion
    *2
    Lock
    *a
    Push in

    NOTICE:
    1. Install the transmission control cable assembly with the protrusion facing upwards.
    2. After installation, make sure that the lock is projecting from A as shown in the illustration.
    3. Make sure that the transmission control cable assembly are securely locked.



    C244594
  1. Confirm that the shift lever is in N, and then connect the end of the transmission control cable assembly to the shift lever assembly.

    NOTICE:
    1. Securely install the end of the transmission control cable assembly to the shift lever assembly.
    2. Install the end of the transmission control cable assembly so that its adjustment lock section is on the driver side.



10. ADJUST SHIFT LEVER POSITION
  1. Move the shift lever to N.



    C195135E01
  1. Slide the adjuster case cover in the direction shown by the arrow.
    Text in Illustration 
    *1
    Adjuster Case
    *2
    Cover
    *3
    Lock Piece

  1. Using a precision screwdriver, pull up the lock piece.



    C195136E01
  1. Using your fingers, gently pull the cable rod towards the rear of the vehicle to remove backlash.
    Text in Illustration 
    *1
    Adjuster Case
    *2
    Lock Piece
    *3
    Cable Rod
    *4
    Cover

  1. Push in the lock piece of the adjuster case to lock it.

  1. Slide the adjuster case cover in the direction shown by the arrow.

    NOTICE:
    If the cover is not pushed over the protrusion on the lock, the cable will not lock and shift operation will not be accurate.



11. INSPECT SHIFT LEVER POSITION
  1. Turn the ignition switch to ON and step on the brake pedal.

  1. Confirm that the shift lever moves smoothly through all of the shift positions and the position indicator shows the correct shift lever position.

  1. Start the engine and confirm that the vehicle moves forward when the shift lever is moved from N to D.



12. INSTALL REAR CONSOLE BOX ASSEMBLY
(Click here)