Home › Drivetrain ยท U340E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT (for Sedan)

AUTOMATIC TRANSAXLE UNIT (for Sedan) > DISASSEMBLY

for Preparation Click here



1. REMOVE SPEEDOMETER SENSOR


C121660
  1. Remove the bolt and remove the speedometer sensor.



2. REMOVE SPEEDOMETER DRIVEN GEAR


C117097E01
  1. Remove the clip and speedometer driven gear from the speedometer sensor.

  1. Remove the O-ring from the speedometer sensor.



3. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


C117101
  1. Remove the nut and washer and remove the control lever shaft.



    C117104
  1. Using a screwdriver, pry out the lock plate and remove the manual valve shaft nut.



    C117106
  1. Remove the 2 bolts and pull out the park/neutral position switch assembly.



4. REMOVE TRANSMISSION REVOLUTION SENSOR


C067751
  1. Remove the bolt and remove the transmission revolution sensor.



5. REMOVE OIL COOLER TUBE UNION


D025286
  1. Remove the 2 oil cooler tube unions from the transaxle case.

  1. Remove the 2 O-rings from the 2 oil cooler tube unions.



6. REMOVE NO. 1 TRANSAXLE CASE PLUG


C067754
  1. Remove the 4 No. 1 transaxle case plugs from the transaxle housing and transaxle case.



    C067755
  1. Remove the No. 1 transaxle case plug from the transaxle case.

  1. Remove the O-rings from the No. 1 transaxle case plugs.



7. REMOVE BREATHER PLUG HOSE


C067752
  1. Remove the breather plug hose from the transaxle case.



8. FIX AUTOMATIC TRANSAXLE ASSEMBLY


9. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


C062684E03
  1. Remove the 19 bolts and remove the oil pan and oil pan gasket.



    C093943E04
  1. Remove the 2 oil cleaner magnets from the oil pan.

  1. Examine the particles in the pan.

    1. Collect any steel chips with the removed magnets.
      Carefully look at the foreign matter and particles in the pan and on the magnets to predict the type of wear which might be found in the transaxle.
      Steel (magnetic): bearing, gear and clutch plate wear
      Brass (non-magnetic): bearing wear



10. REMOVE VALVE BODY OIL STRAINER ASSEMBLY


C062685E02
  1. Remove the 3 bolts and remove the oil strainer assembly.



    D005904E04
  1. Remove the oil strainer gasket from the oil strainer.



11. REMOVE TRANSMISSION VALVE BODY ASSEMBLY
  1. Disconnect the 5 solenoid connectors.



    C093938E05
  1. Remove the bolt and lock plate and remove the ATF temperature sensor.



    C093939E07
  1. Remove the 2 bolts and remove the detent spring cover and detent spring.



    C093940E10
  1. Remove the 13 bolts and the valve body assembly from the transaxle case.



12. REMOVE TRANSMISSION WIRE


C062929
  1. Remove the bolt and the transmission wire from the transaxle case.



    C067760
  1. Remove the O-ring from the transmission wire.



13. REMOVE TRANSAXLE CASE 2ND BRAKE GASKET


C067757
  1. Remove the transaxle case 2nd brake gasket from the transaxle case.



14. REMOVE TRANSAXLE CASE GASKET


C067758
  1. Remove the transaxle case gasket from the transaxle case.



15. REMOVE BRAKE DRUM GASKET


C067759
  1. Remove the brake drum gasket from the transaxle case.



16. REMOVE CHECK BALL BODY


C067767
  1. Remove the check ball body and spring from the transaxle case.



17. REMOVE B-2 ACCUMULATOR PISTON


C067761
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the B-2 accumulator piston and spring.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.
    2. Do not splash ATF with the compressed air.



    D025038
  1. Remove the 2 O-rings from the B-2 accumulator piston.



18. REMOVE C-3 ACCUMULATOR PISTON


C067762
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-3 accumulator piston and spring.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it with your hand using a piece of cloth.
    2. Do not splash ATF with the compressed air.



    D025039
  1. Remove the 2 O-rings from the C-3 accumulator piston.



19. REMOVE C-2 ACCUMULATOR PISTON


C067763
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-2 accumulator piston and the spring.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.
    2. Do not splash ATF with the compressed air.



    D025040
  1. Remove the 2 O-rings from the C-2 accumulator piston.



20. REMOVE TRANSAXLE HOUSING


D025041
  1. Remove the 14 bolts.

  1. Tap around the circumference of the transaxle housing with a plastic hammer to remove the transaxle housing from the transaxle case.

    NOTICE:
    The differential gear assembly may be accidentally removed when the transaxle housing is removed.



21. INSPECT INPUT SHAFT END PLAY


C067772
  1. Measure the end play in the axial direction.

    End play:
    0.37 to 1.29 mm (0.0146 to 0.0508 in.)

    If the end play is not as specified, select and replace the thrust needle roller bearing.



22. REMOVE OIL PUMP ASSEMBLY


C067773
  1. Remove the 7 bolts and the oil pump assembly from the transaxle case.



23. REMOVE DIFFERENTIAL GEAR ASSEMBLY


D025042
  1. Remove the differential gear assembly from the transaxle case.



24. REMOVE OVERDRIVE BRAKE GASKET


C067783
  1. Using a screwdriver, remove the 2 overdrive brake gaskets from the transaxle case.



25. REMOVE INPUT SHAFT ASSEMBLY


C067775
  1. Remove the input shaft assembly from the transaxle case.



26. REMOVE STATOR SHAFT THRUST NEEDLE ROLLER BEARING


C067782
  1. Remove the thrust needle roller bearing from the input shaft.



27. REMOVE FRONT CLUTCH CLUTCH DISC


    C067851
  1. Using a screwdriver, remove the snap ring.

  1. Remove the flange, 4 discs and 4 plates from the input shaft.



28. REMOVE FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY


    D008368E01
  1. Using SST on the clutch balancer, compress the return spring with a press.

    SST
    09320-89010  

    NOTICE:
    Do not compress the return spring excessively.

  1. Using a snap ring expander, remove the snap ring.



    D008369
  1. Remove the clutch balancer and piston return spring.



29. REMOVE FORWARD CLUTCH PISTON


    C067856
  1. Place the input shaft onto the oil pump.

  1. Holding the forward clutch piston by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil pump to remove the forward clutch piston.

    HINT:
    When the piston can not be removed due to being slanted, either blow the air again with the protruding side pushed or remove the piston using needle-nose pliers with their tips wrapped in protective tape.



30. REMOVE FORWARD CLUTCH PISTON O-RING


    C067857
  1. Using a screwdriver, remove the clutch piston O-ring from the forward clutch piston.



31. REMOVE INPUT SHAFT OIL SEAL RING


    C067858
  1. Using a screwdriver, remove the input shaft oil seal ring from the input shaft.



32. REMOVE FORWARD CLUTCH HUB THRUST NEEDLE ROLLER BEARING


C067776
  1. Remove the thrust needle roller bearing from the forward clutch hub.



33. INSPECT INTERMEDIATE SHAFT ASSEMBLY


D025043
  1. Using a dial indicator, measure the clearance of the intermediate shaft.

    Standard clearance:
    0.204 to 0.966 mm (0.008 to 0.038 in.)



34. REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY


C067777
  1. Remove the forward clutch hub from the transaxle case.



35. REMOVE REAR TRANSAXLE COVER ASSEMBLY


C067778
  1. Remove the 11 bolts.

  1. Tap around the circumference of the rear transaxle cover with a plastic hammer to remove the rear transaxle cover from the transaxle case.



36. REMOVE REAR TRANSAXLE COVER PLUG


    C067881
  1. Remove the 4 rear transaxle cover plugs from the rear transaxle cover.

  1. Using a screwdriver, remove the 4 O-rings from the 4 rear transaxle cover plugs.



37. REMOVE OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


    D008358
  1. Using SST, a press and a screwdriver, remove the snap ring.

    SST
    09387-00070  

    NOTICE:
    Stop the press when the overdrive brake piston is lowered to 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove, to prevent the overdrive brake piston from being deformed.

  1. Remove the overdrive brake return spring from the transaxle rear cover.



38. REMOVE 2ND COAST AND OVERDRIVE BRAKE PISTON


    C067883
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle rear cover to remove the overdrive brake piston.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.
    2. Do not splash ATF with the compressed air.



39. REMOVE 2ND COAST AND OVERDRIVE O-RING


    C067884
  1. Using a screwdriver, remove the 2 O-rings from the 2nd coast and overdrive brake piston.



40. REMOVE CLUTCH DRUM OIL SEAL RING


    C067885
  1. Remove the 3 oil seals from the transaxle rear cover.



41. REMOVE REAR TRANSAXLE COVER NEEDLE ROLLER BEARING


    C082194E01
  1. Using SST, remove the bearing from the rear transaxle cover.

    SST
    09387-00041   (09387-01021)



42. REMOVE TRANSAXLE CASE GASKET


C067779
  1. Remove the 4 transaxle case gaskets.



43. REMOVE REAR CLUTCH DRUM THRUST NEEDLE ROLLER BEARING


C067780
  1. Using a magnetic finger, remove the thrust needle roller bearing.



44. REMOVE INTERMEDIATE SHAFT ASSEMBLY


C067781
  1. Remove the intermediate shaft assembly from the transaxle case.



45. REMOVE REVERSE CLUTCH DISC


    C067867
  1. Using a screwdriver, remove the snap ring.

  1. Remove the flange, 2 discs and 2 plates.



46. REMOVE DIRECT CLUTCH DISK


    C067869
  1. Using a screwdriver, remove the snap ring.

  1. Remove the direct clutch flange, 3 plates and 3 rear clutch flanges.



47. REMOVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY


    C067871E01
  1. Using SST and a press, remove the snap ring.

    SST
    09387-00020  

  1. Remove the direct clutch return spring sub-assembly from the intermediate shaft.



48. REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY


    C067873
  1. Install the intermediate shaft onto the transaxle rear cover.

  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole shown in the illustration and remove the direct clutch piston from the intermediate shaft.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.
    2. Do not splash ATF with the compressed air.



49. REMOVE DIRECT CLUTCH DRUM SUB-ASSEMBLY


    D025110
  1. Install the intermediate shaft onto the transaxle rear cover.

  1. Put a matchmark on the direct clutch drum in the same position as the cutout of the intermediate shaft assembly.

  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole shown in the illustration and remove the direct clutch drum from the intermediate shaft.

    NOTICE:
    1. Blowing the air may cause the drum to jump out. When removing the drum, hold it by hand using a piece of cloth.
    2. Do not splash ATF with the compressed air.



50. REMOVE DIRECT CLUTCH PISTON O-RING


    C067875
  1. Using a screwdriver, remove the 2 piston O-rings from the direct clutch piston.



51. REMOVE DIRECT CLUTCH DRUM O-RING


    C067876
  1. Using a screwdriver, remove the direct clutch drum O-ring from the direct clutch drum.



52. REMOVE 2ND COAST AND OVERDRIVE BRAKE DISC


C067785
  1. Remove the flange, 2 discs and 2 No. 2 flanges from the transaxle.



53. REMOVE THRUST NEEDLE ROLLER BEARING


C067784
  1. Using a magnetic finger, remove the C-2 hub thrust bearing race, the thrust needle roller bearing and the thrust bearing race from the direct clutch hub.



54. REMOVE DIRECT CLUTCH HUB


C068196
  1. Remove the direct clutch hub from the transaxle case.



55. REMOVE REAR NO. 2 PLANETARY SUN GEAR THRUST NEEDLE ROLLER BEARING


C067786
  1. Using a magnetic finger, remove the thrust bearing from the rear thrust needle bearing.



56. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY


C067973
  1. Remove the rear planetary sun gear from the transaxle case.



57. REMOVE REAR PLANETARY SUN GEAR THRUST NEEDLE ROLLER BEARING


C068161
  1. Remove the rear planetary sun gear thrust needle roller bearing and thrust washer No. 1 from the rear planetary sun gear.



58. INSPECT 1-WAY CLUTCH ASSEMBLY


D025044E07
  1. Hold the rear planetary sun gear and turn the 1-way clutch.

  1. Make sure that 1-way clutch turns freely counterclockwise and locks when turned clockwise.



59. REMOVE 1-WAY CLUTCH ASSEMBLY


C068163
  1. Remove the 1-way clutch assembly and planetary carrier thrust washer No. 2 from the rear planetary sun gear.



60. REMOVE 2ND COAST AND OVERDRIVE BRAKE FLANGE HOLE SNAP RING


C067971
  1. Using a screwdriver, remove the snap ring from the transaxle case.



61. REMOVE 2ND BRAKE BRAKE DISC


C067969
  1. Using a screwdriver, remove the snap ring.

  1. Remove the flange, 3 discs and 3 plates from the transaxle.



62. REMOVE 2ND BRAKE PISTON SLEEVE


C067970
  1. Remove the 2nd brake piston sleeve from the transaxle case.



63. INSPECT NO. 2 1-WAY CLUTCH


D025045E06
  1. Install the 1-way clutch and the thrust washer onto the rear planetary sun gear.

  1. Hold the rear planetary sun gear and turn the 1-way clutch.

  1. Make sure that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.



64. REMOVE REAR PLANETARY GEAR ASSEMBLY


C067967
  1. Using a screwdriver, remove the snap ring.

  1. Remove the rear planetary gear assembly from the transaxle case.



65. REMOVE REAR PLANETARY GEAR THRUST NEEDLE ROLLER BEARING


C068159
  1. Remove the thrust needle roller bearing and 2 bearing races from the rear planetary gear assembly.



66. REMOVE NO. 2 1-WAY CLUTCH


C067966
  1. Separate the 2nd brake cylinder, 1-way clutch No. 2 and the rear planetary gear.



67. REMOVE OUTER RACE RETAINER


C067965
  1. Remove the retainer from 1-way clutch No. 2.



68. REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    D003796E04
  1. Using SST and a press, remove the snap ring from the 2nd brake piston.

    SST
    09387-00060  

  1. Remove the 2nd brake return spring from the 2nd brake cylinder.



    C067862
  1. Remove the 2nd brake piston return spring sub-assembly from the 2nd brake cylinder.



69. REMOVE 2ND BRAKE PISTON


    C067863
  1. Hold the 2nd brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2 , 57 psi) to the 2nd brake cylinder to remove the 2nd brake piston.



70. REMOVE 2ND BRAKE CYLINDER O-RING


    C067864
  1. Using a screwdriver, remove the 2 O-rings from the 2nd brake cylinder.



71. REMOVE FRONT PLANETARY SUN GEAR


C068157
  1. Remove the front planetary sun gear and thrust needle roller bearing from the transaxle case.



72. REMOVE 1ST AND REVERSE BRAKE DISC


C067963
  1. Using a screwdriver, remove the snap ring.

  1. Remove the flange, 4 discs and 4 plates from the transaxle case.



73. REMOVE COUNTER DRIVE GEAR NUT


C067960
  1. Fix the counter driven gear with the parking lock pawl.



    C067961E01
  1. Using SST and a hammer, release the lock washer.

    SST
    09930-00010  



    D025048E02
  1. Using SST, remove the nut and lock washer.

    SST
    09387-00121  



74. REMOVE PLANETARY GEAR ASSEMBLY


D025047E01
  1. Using SST and a press, remove the planetary gear assembly from the transaxle case.

    SST
    09950-60010   (09951-00400, 09951-00320, 09952-06010)
    09950-70010   (09951-07100)



75. REMOVE COUNTER DRIVE GEAR


C068474E01
  1. Install the 2 bolts onto the counter drive gear.

    Bolt (M6):
    L = 40 to 80 mm
    Pitch = 1.0 mm

  1. Rotate the 2 bolts and remove the counter drive gear and front planetary sun gear.

  1. Remove the 2 radial ball bearings from the counter drive gear and front planetary sun gear.



76. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


D008332E02
  1. Using SST, a press and a screwdriver, remove the snap ring.

    SST
    09387-00070  

  1. Remove the 1st and reverse brake return spring sub-assembly.



77. REMOVE NO. 2 1ST AND REVERSE BRAKE PISTON


C068211
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the 1st and reverse brake piston.

    NOTICE:
    1. Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.
    2. Do not splash ATF with the compressed air.



78. REMOVE NO. 2 1ST AND REVERSE BRAKE PISTON O-RING


C067962
  1. Remove the 2 O-rings from No. 2 1st and reverse brake piston.



79. REMOVE PARKING LOCK PAWL BRACKET


C067957
  1. Remove the 3 bolts, cam guide and bracket from the transaxle case.



80. REMOVE MANUAL VALVE LEVER SHAFT RETAINER SPRING


C067956
  1. Remove the manual valve lever shaft retainer spring from the manual valve lever shaft.



81. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY


C067954
  1. Using a screwdriver, release and remove the spacer.



    C067950
  1. Using a pin punch and hammer, drive out the manual valve lever shaft spring pin.

  1. Remove the manual valve lever shaft and manual valve lever.



82. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


C067951
  1. Remove the parking lock rod from the manual valve lever.



83. REMOVE MANUAL VALVE LEVER SHAFT


C067952
  1. Remove the manual valve lever shaft from the transaxle case.



84. REMOVE PARKING LOCK PAWL


C067948
  1. Using a screwdriver, remove the parking lock pawl shaft from the transaxle case.

  1. Remove the parking lock pawl torsion spring and parking lock pawl from the transaxle case.



85. REMOVE COUNTER DRIVEN GEAR


C068164
  1. Remove the counter driven gear, drive pinion and thrust needle roller bearing from the transaxle case.



86. REMOVE DIFFERENTIAL DRIVE PINION PLUG


C068188
  1. Using a brass bar and a hammer, remove the differential drive pinion plug.



87. REMOVE DIFFERENTIAL DRIVE PINION


D025174E01
  1. Using SST and a press, remove the differential drive pinion from the counter driven gear.

    SST
    09950-60010   (09951-00350)
    09950-70010   (09951-07150)



88. REMOVE BEARING LOCK PLATE


C067770
  1. Remove the bolt and remove the bearing lock plate.



89. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE


C068187
  1. Remove the differential gear lube apply tube from the transaxle housing.



90. REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING


C067771E02
  1. Using SST, remove the front drive pinion front tapered roller bearing from the transaxle housing.

    SST
    09308-10010  



91. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING


C067946E03
  1. Using SST, remove the front drive pinion rear tapered roller bearing from the transaxle case.

    SST
    09612-65014   (09612-01040)

  1. Remove transaxle case plate No. 1 from the transaxle case.



92. REMOVE COUNTER DRIVE GEAR BEARING


D025049
  1. Remove the 2 counter drive gear bearing inner races RH from the transaxle case.

  1. Using SST, remove the counter drive gear bearing LH outer race from the transaxle case.

    SST
    09308-00010  



    D025050
  1. Using SST, remove the counter drive gear bearing rear outer race from the transaxle case.

    SST
    09308-00010  



93. REMOVE COUNTER DRIVE GEAR HOLE SNAP RING


C067955
  1. Using a screwdriver, remove the counter drive gear hole snap ring from the transaxle case.



94. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


C067953
  1. Using a screwdriver, remove the oil seal from the transaxle case.



95. REMOVE FRONT TRANSAXLE CASE OIL SEAL


C067942E01
  1. Using SST and a hammer, remove the oil seal from the transaxle case.

    SST
    09950-60010   (09951-00550)
    09950-70010   (09951-07100)



96. REMOVE TRANSAXLE CASE OIL SEAL


C067941E01
  1. Using SST and a hammer, remove the transaxle case oil seal from the transaxle housing.

    SST
    09950-60010   (09951-00530)
    09950-70010   (09951-07100)