AUTOMATIC TRANSAXLE UNIT (for Hatchback) > REASSEMBLY |
| 1. BEARING POSITION |

| 2. INSPECT DIFFERENTIAL CASE TAPERED ROLLER BEARING PRELOAD |
![]() |
Coat the differential gear assembly and the front differential case tapered roller bearing with Toyota Genuine ATF WS and install them to the transaxle case.
Install the transaxle housing with the 14 bolts.
![]() |
Using SST and a torque wrench, measure the preload of the differential case tapered roller bearing.
| Bearing | Preload |
| New | 0.98 to 1.57 N*m (10.0 to 16.0 kgf*cm 8.7 to 13.9 in.*lbf) |
| Used | 0.49 to 0.78 N*m (5.0 to 8.0 kgf*cm 4.3 to 6.9 in.*lbf) |
| Part No. | Mark | Thickness mm (in.) | Part No. | Mark | Thickness mm (in.) |
| 90564-49001 | 01 | 1.90 (0.0748) | 90564-49011 | 11 | 2.40 (0.0945) |
| 90564-49002 | 02 | 1.95 (0.0768) | 90564-49012 | 12 | 2.45 (0.0965) |
| 90564-49003 | 03 | 2.00 (0.0787) | 90564-49013 | 13 | 2.50 (0.0984) |
| 90564-49004 | 04 | 2.05 (0.0807) | 90564-49014 | 14 | 2.55 (0.1004) |
| 90564-49005 | 05 | 2.10 (0.0827) | 90564-49015 | 15 | 2.60 (0.1024) |
| 90564-49006 | 06 | 2.15 (0.0846) | 90564-49016 | 16 | 2.65 (0.1043) |
| 90564-49007 | 07 | 2.20 (0.0866) | 90564-49017 | 17 | 2.70 (0.1063) |
| 90564-49008 | 08 | 2.25 (0.0885) | 90564-49018 | 18 | 2.75 (0.1082) |
| 90564-49009 | 09 | 2.30 (0.0906) | 90564-49019 | 19 | 2.80 (0.1102) |
| 90564-49010 | 10 | 2.35 (0.0925) | - | - | - |
| 3. INSTALL TRANSAXLE CASE OIL SEAL |
![]() |
Coat the lip of a new transaxle case oil seal with MP grease.
Using SST and a hammer, drive in the transaxle case oil seal.
| 4. INSTALL FRONT TRANSAXLE CASE OIL SEAL |
![]() |
Coat the lip of a new front transaxle case oil seal with MP grease.
Using SST and a hammer, drive in the front transaxle case oil seal.
| 5. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL |
![]() |
Coat the lip of a new manual valve lever shaft oil seal with MP grease.
Using SST and a hammer, install a new manual valve lever shaft oil seal.
| 6. INSTALL COUNTER DRIVE GEAR HOLE SNAP RING |
![]() |
Using a screwdriver, install the counter drive gear hole snap ring to the transaxle case.
| 7. INSTALL COUNTER DRIVE GEAR BEARING |
![]() |
Using SST and a hammer, install the counter drive gear bearing outer race to the transaxle case.
![]() |
Using SST and a hammer, install the counter drive gear bearing outer race to the transaxle case.
Install the 2 counter drive gear bearing inner races and 2 angular balls to the transaxle case.
| 8. INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING |
![]() |
Install the No. 1 transaxle case plate to the transaxle case.
| *1 | No. 1 Transaxle Case Plate |
| *a | Bearing Side |
| *b | Transaxle Case Side |
![]() |
Using SST and a hammer, install the new front drive pinion rear tapered roller bearing to the transaxle case.
| 9. INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING |
Install the drive pinion thrust bearing RH to the transaxle housing.
![]() |
Using SST and a press, install a new front drive pinion front tapered roller bearing to the transaxle housing.
| 10. INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE |
![]() |
Install the differential gear lube apply tube to the transaxle housing.
| 11. INSTALL BEARING LOCK PLATE |
![]() |
Install the bearing lock plate to the transaxle housing with the bolt.
| 12. INSTALL DIFFERENTIAL DRIVE PINION PLUG |
![]() |
Using SST and a plastic hammer, install a new differential drive pinion plug to the differential drive pinion sub-assembly.
| 13. INSTALL DIFFERENTIAL DRIVE PINION SUB-ASSEMBLY |
![]() |
Install the differential drive pinion sub-assembly and the drive pinion thrust bearing LH to the transaxle case.
| 14. INSTALL PARKING LOCK PAWL |
![]() |
Coat the parking lock pawl shaft with Toyota Genuine ATF WS.
Install the parking lock pawl, parking lock pawl shaft torsion spring and the parking lock pawl shaft to the transaxle case.
| 15. INSTALL MANUAL VALVE LEVER SHAFT |
![]() |
Install the manual valve lever shaft to the transaxle case.
| 16. INSTALL PARKING LOCK ROD SUB-ASSEMBLY |
![]() |
Install the parking lock rod sub-assembly to the manual valve lever sub-assembly.
| 17. INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY |
Coat the manual valve lever sub-assembly with Toyota Genuine ATF WS.
Install the manual valve lever sub-assembly and a new manual valve lever shaft spacer to the manual valve lever shaft.
![]() |
Using a pin punch 3 mm and hammer, drive in the manual valve lever shaft spring pin.
![]() |
Turn the manual valve lever shaft spacer and the manual valve lever shaft to align the small hole for locating the staking position in the manual valve lever shaft spacer with the staking position mark on the manual valve lever shaft.
Using a punch, stake the manual valve lever shaft spacer through the small hole.
Check that the manual valve lever shaft spacer does not turn.
| 18. INSTALL MANUAL VALVE LEVER SHAFT RETAINER SPRING |
![]() |
Install the manual valve lever shaft retainer spring to the manual valve lever shaft.
| 19. INSTALL PARKING LOCK PAWL BRACKET |
![]() |
Install the parking lock rod sub-assembly, parking lock cam guide and the parking lock pawl bracket to the transaxle case with the 3 bolts.
| 20. INSTALL NO. 2 1ST AND REVERSE BRAKE PISTON O-RING |
![]() |
Coat 2 new No. 2 1st and reverse brake piston O-rings with Toyota Genuine ATF WS, and install them to the No. 2 1st and reverse brake piston.
| 21. INSTALL NO. 2 1ST AND REVERSE BRAKE PISTON |
![]() |
Coat the No. 2 1st and reverse brake piston with Toyota Genuine ATF WS, and install it to the transaxle case.
| 22. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Install the 1st and reverse brake return spring sub-assembly to the transaxle case.
Using SST, a press and a screwdriver, install the snap ring to the transaxle case.
| 23. INSTALL COUNTER DRIVE GEAR |
![]() |
Using SST and a press, install the counter drive gear to the transaxle case.
| 24. INSTALL PLANETARY GEAR ASSEMBLY |
![]() |
Using SST and a press, install the planetary gear assembly to the transaxle case.
| 25. INSTALL COUNTER DRIVE GEAR NUT |
![]() |
Fix the counter driven gear with the parking lock pawl.
![]() |
Using SST, install a new counter drive gear lock nut washer and the counter drive gear nut.
![]() |
Using SST and a torque wrench, measure the rotating torque while turning the counter drive gear at 60 turns per minute.
![]() |
Using SST and a hammer, stake the counter drive gear lock nut washer.
| 26. INSTALL 1ST AND REVERSE BRAKE DISC |
![]() |
Install the 4 1st and reverse brake plates, 4 1st and reverse brake discs and the 1st and reverse brake flange to the transaxle case.
| *1 | Snap Ring |
| *2 | 1st and Reverse Brake Flange |
| *3 | 1st and Reverse Brake Disc |
| *4 | 1st and Reverse Brake Plate |
Using a screwdriver, install the snap ring to the transaxle case.
| 27. INSPECT PACK CLEARANCE OF FIRST AND REVERSE BRAKE |
![]() |
Using SST and a dial indicator, measure the 1st and reverse brake clearance while pressing the 1st and reverse brake disc and the 1st and reverse brake plate from the rear side.
| Part No. | Mark | Thickness mm (in.) |
| 35679-52020 | - | 3.4 (0.134) |
| 35679-52030 | 1 | 3.6 (0.142) |
| 35679-52040 | 2 | 3.8 (0.150) |
| 35679-52050 | 3 | 4.0 (0.157) |
Check that the 1st and reverse brake piston moves when compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) is applied to the oil hole.
| 28. INSTALL FRONT PLANETARY SUN GEAR |
![]() |
Install the front planetary sun gear and the front planetary gear thrust needle roller bearing to the planetary gear assembly.
| 29. INSTALL 2ND BRAKE CYLINDER O-RING |
![]() |
Coat 2 new 2nd brake cylinder O-rings with Toyota Genuine ATF WS, and install them to the 2nd brake cylinder.
| 30. INSTALL 2ND BRAKE PISTON |
![]() |
Coat the 2nd brake piston with Toyota Genuine ATF WS, and install it to the 2nd brake cylinder.
| 31. INSTALL 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Install the 2nd brake piston return spring sub-assembly to the 2nd brake cylinder.
![]() |
Place SST on the 2nd brake piston return spring sub-assembly, and compress the 2nd brake piston return spring sub-assembly with a press.
Using a screwdriver, install the snap ring.
| 32. INSTALL OUTER RACE RETAINER |
![]() |
Install the outer race retainer to the No. 2 1-way clutch.
| 33. INSTALL NO. 2 1-WAY CLUTCH |
![]() |
Install the No. 2 1-way clutch and the 2nd brake piston assembly to the rear planetary gear assembly.
| 34. INSTALL REAR PLANETARY GEAR THRUST NEEDLE ROLLER BEARING |
![]() |
Install the No. 2 thrust bearing race, rear planetary gear thrust needle roller bearing and the thrust bearing race to the rear planetary gear assembly.
| 35. INSTALL REAR PLANETARY GEAR ASSEMBLY |
![]() |
Install the rear planetary gear assembly to the transaxle case.
Using a screwdriver, install the snap ring to the transaxle case.
| 36. INSPECT NO. 2 1-WAY CLUTCH |
![]() |
Check that the rear planetary gear assembly turns freely counterclockwise and locks when turned clockwise.
![]() | Lock |
![]() | Free |
| 37. INSTALL 2ND BRAKE PISTON SLEEVE |
![]() |
Install the 2nd brake piston sleeve to the transaxle case.
| 38. INSTALL 2ND BRAKE BRAKE DISC |
![]() |
Install the 3 2nd brake brake discs, 3 No. 1 2nd brake brake flanges and the 2nd brake brake flange to the transaxle case.
| *1 | 2nd Brake Brake Flange |
| *2 | 2nd Brake Brake Disc |
| *3 | No. 1 2nd Brake Brake Flange |
Using a screwdriver, install the snap ring to the transaxle case.
| 39. INSPECT PACK CLEARANCE OF 2ND BRAKE |
![]() |
Using a dial indicator, measure the 2nd brake pack clearance while applying and releasing compressed air (392 to 785 kPa, 4 to 8 kgf/cm2, 57 to 114 psi).
| Part No. | Mark | Thickness mm (in.) |
| 35678-52020 | - | 3.0 (0.118) |
| 35678-52030 | 1 | 3.2 (0.126) |
| 35678-52040 | 2 | 3.4 (0.134) |
| 35678-52050 | 3 | 3.6 (0.142) |
| 40. INSTALL 2ND COAST AND OVERDRIVE BRAKE FLANGE HOLE SNAP RING |
![]() |
Using a screwdriver, install the 2nd coast and overdrive brake flange hole snap ring to the transaxle case.
| 41. INSTALL 1-WAY CLUTCH ASSEMBLY |
![]() |
Install the No. 2 planetary carrier thrust washer and the 1-way clutch assembly to the rear planetary sun gear assembly.
| 42. INSPECT 1-WAY CLUTCH ASSEMBLY |
![]() |
Hold the rear planetary sun gear and turn the 1-way clutch assembly and check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.
| *a | Free |
| *b | Lock |
| *c | Hold |
| 43. INSTALL REAR PLANETARY SUN GEAR THRUST NEEDLE ROLLER BEARING |
![]() |
Install the rear planetary sub gear thrust needle roller bearing and the No. 1 planetary carrier thrust washer to the rear planetary sun gear assembly.
| 44. INSTALL REAR PLANETARY SUN GEAR ASSEMBLY |
![]() |
Install the rear planetary sun gear assembly to the transaxle case.
| 45. INSTALL REAR NO. 2 PLANETARY SUN GEAR THRUST NEEDLE ROLLER BEARING |
![]() |
Install the rear No. 2 planetary sun gear thrust needle roller bearing to the rear planetary sun gear assembly.
| 46. INSTALL DIRECT CLUTCH HUB |
![]() |
Install the direct clutch hub to the transaxle case.
| 47. INSTALL THRUST NEEDLE ROLLER BEARING |
![]() |
Install the No. 3 thrust bearing race, thrust needle roller bearing and the C-2 hub thrust bearing race to the direct clutch hub.
| 48. INSTALL 2ND COAST AND OVERDRIVE BRAKE DISC |
![]() |
Install the 2 2nd coast and overdrive brake discs, 2 No. 2 2nd coast and overdrive brake flanges and the 2nd coast and overdrive brake flange to the transaxle case.
| *1 | 2nd Coast and Overdrive Brake Flange |
| *2 | 2nd Coast and Overdrive Brake Disc |
| *3 | No. 2 2nd Coast and Overdrive Brake Flange |
| 49. INSTALL DIRECT CLUTCH DRUM O-RING |
![]() |
Coat a new direct clutch drum O-ring with Toyota Genuine ATF WS, and install it to the direct clutch drum sub-assembly.
| 50. INSTALL DIRECT CLUTCH PISTON O-RING |
![]() |
Coat 2 new direct clutch piston O-rings with Toyota Genuine ATF WS, and install them to the direct clutch piston sub-assembly.
| 51. INSTALL DIRECT CLUTCH DRUM SUB-ASSEMBLY |
![]() |
Align the cutout in the intermediate shaft with the matchmark on the direct clutch drum sub-assembly and install the direct clutch drum sub-assembly to the intermediate shaft.
| 52. INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY |
![]() |
Coat the direct clutch piston sub-assembly with Toyota Genuine ATF WS, and install it to the intermediate shaft.
| 53. INSTALL DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Install the direct clutch return spring sub-assembly to the direct clutch piston sub-assembly.
Place SST on the direct clutch return spring sub-assembly and compress the springs with a press.
Using a snap ring expander, install the snap ring to the direct clutch drum sub-assembly.
| 54. INSTALL DIRECT CLUTCH DISC |
![]() |
Coat the direct clutch flange, 3 direct clutch discs and the 3 rear clutch flanges with Toyota Genuine ATF WS, and install them to the intermediate shaft.
| *1 | Snap Ring |
| *2 | Direct Clutch Flange |
| *3 | Direct Clutch Disc |
| *4 | Rear Clutch Flange |
Install the snap ring to the intermediate shaft.
| 55. INSTALL REVERSE CLUTCH DISC |
![]() |
Coat the 2 No. 3 clutch plates, 2 reverse clutch discs and the reverse clutch flange with Toyota Genuine ATF WS, and install them to the intermediate shaft.
| *1 | Snap Ring |
| *2 | Reverse Clutch Flange |
| *3 | Reverse Clutch Disc |
| *4 | No. 3 Clutch Plate |
Install the snap ring to the intermediate shaft.
| 56. INSPECT PACK CLEARANCE OF REVERSE CLUTCH |
![]() |
Install the intermediate shaft assembly and the rear clutch drum thrust needle roller bearing to the rear transaxle cover.
Using a dial indicator, measure the reverse clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).
| Part No. | Mark | Thickness mm (in.) |
| 35649-52020 | - | 3.0 (0.118) |
| 35649-52030 | 1 | 3.2 (0.126) |
| 35649-52040 | 2 | 3.4 (0.134) |
| 35649-52050 | 3 | 3.6 (0.142) |
| 57. INSPECT PACK CLEARANCE OF DIRECT CLUTCH |
![]() |
Install the intermediate shaft assembly and the rear clutch drum thrust needle roller bearing to the rear transaxle cover.
Using SST and a dial indicator, measure the direct clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).
| Part No. | Mark | Thickness mm (in.) |
| 35675-52040 | - | 3.0 (0.118) |
| 35675-52050 | 1 | 3.2 (0.126) |
| 35675-52060 | 2 | 3.4 (0.134) |
| 35675-52070 | 3 | 3.6 (0.142) |
| 58. INSTALL INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Install the intermediate shaft assembly to the transaxle case.
| 59. INSPECT 2ND COAST AND OVERDRIVE BRAKE CLEARANCE |
![]() |
As shown in the illustration, place a straightedge on the transaxle case and measure the distance between the 2nd coast and overdrive brake flange and straightedge using a vernier caliper. (Dimension A)
![]() |
As shown in the illustration, place a straightedge on the 2nd coast and overdrive brake piston and measure the distance between the rear transaxle cover and straightedge using a vernier caliper. (Dimension B)
Calculate the piston stroke value using the following formula. Select a 2nd coast and overdrive brake flange which meets the piston stroke value and install it.
| Part No. | Mark | Thickness mm (in.) |
| 34625-52110 | 4 | 4.0 (0.158) |
| 34625-52071 | 5 | 4.2 (0.165) |
| 34625-52081 | 6 | 4.4 (0.173) |
| 34625-52091 | 7 | 4.6 (0.181) |
| 60. INSTALL REAR CLUTCH DRUM THRUST NEEDLE ROLLER BEARING |
![]() |
Install the rear clutch drum thrust needle roller bearing to the intermediate shaft assembly.
| 61. INSPECT INTERMEDIATE SHAFT ASSEMBLY |
Install the rear transaxle cover with the 11 bolts.
![]() |
Using a dial indicator, measure the clearance of the intermediate shaft assembly.
Remove the 11 bolts and the rear transaxle cover.
| 62. INSTALL TRANSAXLE CASE GASKET |
![]() |
Install 4 new transaxle case gaskets to the transaxle case.
| 63. INSTALL REAR TRANSAXLE COVER NEEDLE ROLLER BEARING |
![]() |
Coat a new rear transaxle cover needle roller bearing with Toyota Genuine ATF WS.
Using SST and a press, install the rear transaxle cover needle roller bearing to the rear transaxle cover.
| 64. INSTALL CLUTCH DRUM OIL SEAL RING |
![]() |
Compress 3 new clutch drum oil seal rings from both sides to reduce dimension A.
Coat the 3 clutch drum oil seal rings with Toyota Genuine ATF WS, and install them to the rear transaxle cover.
| 65. INSTALL 2ND COAST AND OVERDRIVE O-RING |
![]() |
Coat 2 new 2nd coast and overdrive O-rings with Toyota Genuine ATF WS, and install them to the 2nd coast and overdrive brake piston.
| 66. INSTALL 2ND COAST AND OVERDRIVE BRAKE PISTON |
![]() |
Coat the 2nd coast and overdrive brake piston with Toyota Genuine ATF WS, and install it to the rear transaxle cover.
| 67. INSTALL OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Install the overdrive brake return spring sub-assembly to the rear transaxle cover.
![]() |
Using SST and a press, shorten the overdrive brake return spring sub-assembly, then install the snap ring.
| 68. INSTALL REAR TRANSAXLE COVER PLUG |
![]() |
Coat 4 new O-rings with Toyota Genuine ATF WS, and install them to the 4 rear transaxle cover plugs.
Install the 4 rear transaxle cover plugs to the rear transaxle cover.
| 69. INSTALL REAR TRANSAXLE COVER ASSEMBLY |
![]() |
Apply seal packing to the transaxle case.
| *a | Seal Packing (Seal Diameter: 1.2 mm (0.0472 in.)) |
![]() |
Install the rear transaxle cover assembly with the 11 bolts.
| 70. INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY |
![]() |
Install the forward clutch hub sub-assembly to the transaxle case.
| 71. INSTALL FORWARD CLUTCH HUB THRUST NEEDLE ROLLER BEARING |
![]() |
Install the forward clutch hub thrust needle roller bearing to the forward clutch hub sub-assembly.
| 72. INSTALL INPUT SHAFT OIL SEAL RING |
![]() |
Coat a new input shaft oil seal ring with Toyota Genuine ATF WS, and install it to the input shaft sub-assembly.
| 73. INSTALL FORWARD CLUTCH PISTON O-RING |
![]() |
Coat a new forward clutch piston O-ring with Toyota Genuine ATF WS, and install it to the forward clutch piston.
| 74. INSTALL FORWARD CLUTCH PISTON |
![]() |
Install the forward clutch piston to the input shaft sub-assembly.
| 75. INSTALL FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Install the forward clutch return spring sub-assembly and the No. 1 clutch balancer to the input shaft sub-assembly.
![]() |
Using SST, a press and snap ring expander, install the snap ring to the input shaft sub-assembly.
| 76. INSTALL FRONT CLUTCH CLUTCH DISC |
![]() |
Install the 4 No. 1 clutch plates, 4 front clutch clutch discs and the forward clutch flange.
| *1 | Snap Ring |
| *2 | Forward Clutch Flange |
| *3 | Front Clutch Clutch Disc |
| *4 | No. 1 Clutch Plate |
Using a screwdriver, install the snap ring to the input shaft sub-assembly.
| 77. INSPECT PACK CLEARANCE OF FORWARD CLUTCH |
![]() |
Using a dial indicator, measure the pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).
| Part No. | Mark | Thickness mm (in.) |
| 35635-52050 | - | 3.0 (0.118) |
| 35635-52060 | 1 | 3.2 (0.126) |
| 35635-52070 | 2 | 3.4 (0.134) |
| 35635-52080 | 3 | 3.6 (0.142) |
| 78. INSTALL STATOR SHAFT THRUST NEEDLE ROLLER BEARING |
![]() |
Install the stator shaft thrust needle roller bearing to the input shaft assembly.
| 79. INSTALL INPUT SHAFT ASSEMBLY |
![]() |
Install the input shaft assembly to the transaxle case.
| 80. INSTALL OVERDRIVE BRAKE GASKET |
![]() |
Install 2 new overdrive brake gaskets to the transaxle case.
| 81. INSTALL DIFFERENTIAL GEAR ASSEMBLY |
![]() |
Install the differential gear assembly to the transaxle case.
| 82. INSTALL OIL PUMP ASSEMBLY |
![]() |
Install the oil pump assembly to the transaxle case with the 7 bolts.
| 83. INSPECT INPUT SHAFT ASSEMBLY |
![]() |
Make sure that the input shaft turns smoothly.
If the input shaft assembly does not operate normally, replace it.
| 84. INSPECT INPUT SHAFT END PLAY |
![]() |
Measure the end play in the axial direction.
| 85. INSTALL TRANSAXLE HOUSING |
![]() |
Apply seal packing to the transaxle case.
| *a | Seal Packing (Seal Diameter: 1.2 mm (0.0472 in.)) |
![]() |
Apply adhesive to 2 or 3 threads on the end of the 3 bolts B.
![]() |
Install the transaxle housing with the 14 bolts.
| 86. INSTALL C-2 ACCUMULATOR PISTON |
![]() |
Coat 2 new C-2 accumulator piston O-rings with Toyota Genuine ATF WS, and install them to the C-2 accumulator piston.
![]() |
Install the C-2 accumulator piston compression spring and the C-2 accumulator piston.
| Spring | Free Length/ Outer Diameter mm (in.) | Color |
| C-2 | 66.90 (2.6339) 17.20 (0.6772) | - |
| 87. INSTALL C-3 ACCUMULATOR PISTON |
![]() |
Coat 2 new C-3 accumulator piston O-rings with Toyota Genuine ATF WS, and install them to the C-3 accumulator piston.
![]() |
Install the C-3 accumulator piston compression spring and the C-3 accumulator piston.
| Spring | Free Length/ Outer Diameter mm (in.) | Color |
| C-3 | 80.20 (3.1575) 18.70 (0.7362) | Blue |
| 88. INSTALL B-2 ACCUMULATOR PISTON |
![]() |
Coat 2 new B-2 accumulator piston O-rings with Toyota Genuine ATF WS, and install them to the B-2 accumulator piston.
![]() |
Install the B-2 accumulator piston compression spring and the B-2 accumulator piston.
| Spring | Free Length/ Outer Diameter mm (in.) | Color |
| B-2 | 66.90 (2.6339) 15.50 (0.6102) | Green |
| 89. INSTALL CHECK BALL BODY |
![]() |
Install the check ball body compression spring and the check ball body to the transaxle case.
| 90. INSTALL BRAKE DRUM GASKET |
![]() |
Install a new brake drum gasket to the transaxle case.
| 91. INSTALL TRANSAXLE CASE GASKET |
![]() |
Coat a new transaxle case gasket with Toyota Genuine ATF WS, and install it to the transaxle case.
| 92. INSTALL TRANSAXLE CASE 2ND BRAKE GASKET |
![]() |
Coat a new transaxle case 2nd brake gasket with Toyota Genuine ATF WS, and install it to the transaxle case.
| 93. INSTALL TRANSMISSION WIRE |
![]() |
Coat a new O-ring with Toyota Genuine ATF WS, and install it to the transmission wire.
![]() |
Pass the transmission wire through the transaxle case.
![]() |
Install the transmission wire with the bolt.
| 94. INSTALL TRANSMISSION VALVE BODY ASSEMBLY |
Align the groove of the manual valve with the pin of the manual valve lever.
![]() |
Temporarily install the transmission valve body assembly with the 13 bolts.
| Bolt | Bolt Length |
| A | 32 mm (1.260 in.) |
| B | 20 mm (0.787 in.) |
| C | 55 mm (2.165 in.) |
| D | 45 mm (1.772 in.) |
![]() |
Temporarily install the manual detent spring and the manual detent spring cover with the 2 bolts.
| *1 | Manual Detent Spring |
| *2 | Manual Detent Spring Cover |
| Bolt | Bolt Length |
| A | 14 mm (0.551 in.) |
| B | 45 mm (1.772 in.) |
Check that the manual valve lever comes into contact with the center of the roller at the tip of the manual detent spring.
Tighten the 15 bolts.
![]() |
Connect the 5 solenoid connectors.
Install the transmission wire with the lock plate and bolt.
| 95. INSTALL VALVE BODY OIL STRAINER ASSEMBLY |
![]() |
Coat a new oil strainer gasket with Toyota Genuine ATF WS, and install it to the valve body oil strainer assembly.
![]() |
Install the valve body oil strainer assembly to the with the 3 bolts.
| 96. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY |
![]() |
Install the 2 oil cleaner magnets to the automatic transaxle oil pan sub-assembly.
![]() |
Apply adhesive to 2 or 3 threads on the end of the 2 bolts A.
![]() |
Install the automatic transaxle oil pan sub-assembly and a new automatic transaxle oil pan gasket with the 19 bolts.
Install the drain plug and a new gasket to the automatic transaxle oil pan sub-assembly.
| 97. INSTALL BREATHER PLUG |
Install the breather plug to the transaxle case.
| 98. INSTALL TRANSMISSION BREATHER HOSE SUB-ASSEMBLY |
![]() |
Install the transmission breather hose sub-assembly to the breather plug.
| 99. INSTALL NO. 1 TRANSAXLE CASE PLUG |
![]() |
Coat 5 new O-rings with Toyota Genuine ATF WS, and install them to the No. 1 transaxle case plugs.
Install the 4 No. 1 transaxle case plugs to the transaxle housing and the transaxle case.
![]() |
Install the No. 1 transaxle case plug to the transaxle case.
| 100. INSTALL OIL COOLER TUBE UNION |
![]() |
Coat 2 new O-rings with Toyota Genuine ATF WS, and install them to the 2 oil cooler tube unions.
Install the 2 oil cooler tube unions to the transaxle case.
| 101. INSTALL TRANSMISSION REVOLUTION SENSOR |
![]() |
Coat a new O-ring with Toyota Genuine ATF WS, and install it to the transmission revolution sensor.
Install the transmission revolution sensor to the transaxle case with the bolt.
| 102. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Install the park/neutral position switch assembly.
Temporarily install the 2 bolts.
Replace the lock plate with a new one and install the nut, lock plate and washer.
Temporarily install the transmission control shaft lever.
![]() |
Turn the lever counterclockwise until it stops, then turn it clockwise 2 notches.
Remove the transmission control shaft lever.
![]() |
Align the groove with the neutral basic line.
| *a | Neutral Basic Line |
| *b | Groove |
Hold the switch in this position and tighten the 2 bolts.
![]() |
Using a screwdriver, stake the nut with the lock plate.
| 103. INSTALL TRANSMISSION CONTROL SHAFT LEVER |
![]() |
Install the transmission control shaft lever with the nut and washer.