Home › Drivetrain ยท C50 MANUAL TRANSMISSION / TRANSAXLE › OUTPUT SHAFT (for Hatchback)

OUTPUT SHAFT (for Hatchback) > DISASSEMBLY

for Preparation Click here



1. INSPECT 1ST GEAR THRUST CLEARANCE


C080538
  1. Using a feeler gauge, measure the 1st gear thrust clearance.

    Standard clearance:
    0.10 to 0.40 mm (0.00394 to 0.0157 in.)

    Maximum clearance:
    0.40 mm (0.0157 in.)

    If the clearance exceeds the maximum, replace the 1st gear thrust washer, 1st gear, or No. 1 transmission clutch hub.



2. INSPECT 2ND GEAR THRUST CLEARANCE


C068312
  1. Using a dial indicator, measure the 2nd gear thrust clearance.

    Standard clearance:
    0.10 to 0.55 mm (0.00394 to 0.0217 in.)

    Maximum clearance:
    0.55 mm (0.0217 in.)

    If the clearance exceeds the maximum, replace the No. 1 transmission clutch hub, 2nd gear, or 3rd driven gear.



3. INSPECT 1ST GEAR RADIAL CLEARANCE


C068309
  1. Using a dial indicator, measure the 1st gear radial clearance between the gear and shaft.

    Standard clearance:
    JTEKT made:
    0.015 to 0.058 mm (0.000591 to 0.00228 in.)
    NSK made:
    0.015 to 0.056 mm (0.000591 to 0.00220 in.)

    Maximum clearance:
    JTEKT made:
    0.058 mm (0.00228 in.)
    NSK made:
    0.056 mm (0.00220 in.)

    If the clearance exceeds the maximum, replace the 1st gear or 1st gear needle roller bearing.



4. INSPECT 2ND GEAR RADIAL CLEARANCE


C068254
  1. Using a dial indicator, measure the 2nd gear radial clearance between the gear and shaft.

    Standard clearance:
    JTEKT made:
    0.015 to 0.058 mm (0.000591 to 0.00228 in.)
    NSK made:
    0.015 to 0.056 mm (0.000591 to 0.00220 in.)

    Maximum clearance:
    JTEKT made:
    0.058 mm (0.00228 in.)
    NSK made:
    0.056 mm (0.00220 in.)

    If the clearance exceeds the maximum, replace the 2nd gear or 2nd gear needle roller bearing.



5. REMOVE 4TH DRIVEN GEAR


C080539E02
  1. Using SST and a press, remove the output shaft rear bearing and 4th driven gear from the output shaft.

    SST
    09950-00020  



6. REMOVE OUTPUT GEAR SPACER


C068005
  1. Remove the output gear spacer from the output shaft.



7. REMOVE 2ND GEAR


G027264E03
  1. Using SST and a press, remove the 3rd driven gear with 2nd gear from the output shaft.

    SST
    09950-00020  



8. REMOVE 2ND GEAR NEEDLE ROLLER BEARING


    C080541
  1. Remove the 2nd gear needle roller bearing and 2nd gear bearing spacer from the output shaft.



9. REMOVE NO. 1 SYNCHRONIZER RING (FOR 2ND GEAR)


C120730
  1. Remove the No. 1 synchronizer ring from the output shaft.



10. REMOVE 1ST GEAR


C080543
  1. Using 2 screwdrivers and a hammer, remove the snap ring from the output shaft.

    HINT:
    Use a piece of cloth to keep the snap ring from flying off.



    C080544E04
  1. Using SST and a press, remove the No. 1 transmission clutch hub assembly and 1st gear from the output shaft.

    SST
    09950-00020  

    NOTICE:
    1. Do not tighten SST excessively.
    2. Support the input shaft by hand to prevent it from dropping off.



11. REMOVE NO. 1 SYNCHRONIZER RING (FOR 1ST GEAR)


    C080465
  1. Remove the No. 1 synchronizer ring from the 1st gear.



12. REMOVE 1ST GEAR NEEDLE ROLLER BEARING


C068012
  1. Remove the 1st gear needle roller bearing from the output shaft.



13. REMOVE 1ST GEAR THRUST WASHER


C068013
  1. Remove the 1st gear thrust washer from the output shaft.



14. REMOVE 1ST GEAR THRUST WASHER PIN OR BALL


C068014
  1. Remove the 1st gear thrust washer pin or ball from the output shaft.



15. REMOVE REVERSE GEAR


C068015
  1. Remove the reverse gear, 3 synchromesh shifting keys, and 3 synchromesh shifting key springs from the No. 1 transmission clutch hub.

    NOTICE:
    Use a piece of cloth to keep the shifting key and shifting key spring from flying off.