OUTPUT SHAFT (for Hatchback) > REASSEMBLY |
| 1. INSTALL REVERSE GEAR |
![]() |
Coat the reverse gear with gear oil and install it onto the No. 1 transmission clutch hub.
Install the 3 synchromesh shifting key springs and 3 synchromesh keys onto the No. 1 transmission clutch hub.
| 2. INSTALL 1ST GEAR THRUST WASHER PIN OR BALL |
![]() |
Coat the 1st gear thrust washer pin or ball with MP grease, and install it onto the output shaft.
| 3. INSTALL 1ST GEAR THRUST WASHER |
![]() |
Coat the 1st gear thrust washer with gear oil and install it onto the output shaft.
| 4. INSTALL 1ST GEAR NEEDLE ROLLER BEARING |
![]() |
Coat the 1st gear needle roller bearing with gear oil and install it onto the output shaft.
| 5. INSTALL 1ST GEAR |
![]() |
Coat the 1st gear with gear oil and install it onto the output shaft.
| 6. INSTALL NO. 1 SYNCHRONIZER RING (FOR 1ST GEAR) |
![]() |
Coat the No. 1 synchronizer ring with gear oil and install it onto the 1st gear.
| 7. INSTALL NO. 1 TRANSMISSION CLUTCH HUB |
![]() |
Using SST and a press, install the No. 1 transmission clutch hub onto the output shaft.
![]() |
Select a snap ring that will allow minimum axial play.
| Part No. | Mark | Thickness mm (in.) |
| 09520-29018 | A | 2.50 (0.0984) |
| 09520-29019 | B | 2.56 (0.1008) |
| 09520-29020 | C | 2.62 (0.1031) |
| 09520-29021 | D | 2.68 (0.1055) |
| 09520-29022 | E | 2.74 (0.1079) |
| 09520-29023 | F | 2.80 (0.1102) |
Using a brass bar and a hammer, install the snap ring onto the output shaft.
| 8. INSTALL 2ND GEAR NEEDLE ROLLER BEARING |
![]() |
Coat the 2nd gear needle roller bearing and 2nd gear bearing spacer with gear oil, and install them onto the output shaft.
| 9. INSTALL NO. 1 SYNCHRONIZER RING (FOR 2ND GEAR) |
Coat the No. 1 synchronizer ring with gear oil.
![]() |
Install the No. 1 synchronizer inner ring onto the 2nd gear.
![]() |
Install the No. 1 synchronizer middle ring onto the 2nd gear.
![]() |
Install the No. 1 synchronizer outer ring onto the 2nd gear.
| 10. INSTALL 2ND GEAR |
![]() |
Coat the 2nd gear with gear oil and install it onto the output shaft.
| 11. INSTALL 3RD DRIVEN GEAR |
![]() |
Using SST and a press, install the 3rd driven gear onto the output shaft.
| 12. INSTALL OUTPUT GEAR SPACER |
![]() |
Install the output gear spacer onto the output shaft.
| 13. INSTALL 4TH DRIVEN GEAR |
![]() |
Using SST and a press, install the 4th driven gear onto the output shaft.
| 14. INSTALL OUTPUT SHAFT REAR BEARING |
![]() |
Using SST and a press, install the output shaft rear bearing onto the output shaft.
| 15. INSPECT 2ND GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the 2nd gear radial clearance between the gear and shaft.
| 16. INSPECT 1ST GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the 1st gear radial clearance between the gear and shaft.
| 17. INSPECT 2ND GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the 2nd gear thrust clearance.
| 18. INSPECT 1ST GEAR THRUST CLEARANCE |
![]() |
Using a feeler gauge, measure the 1st gear thrust clearance.