MANUAL TRANSAXLE UNIT (for Sedan) > DISASSEMBLY |
| 1. REMOVE MANUAL TRANSMISSION FILLER PLUG |
![]() |
Remove the manual transmission filler plug and gasket from the manual transmission case.
| 2. REMOVE DRAIN PLUG SUB-ASSEMBLY |
![]() |
Remove the drain plug sub-assembly and gasket from the manual transmission case.
| 3. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY |
Remove the bolt and speedometer driven hole cover sub-assembly from the transaxle case.
Remove the O-ring from the speedometer driven hole cover sub-assembly.
| 4. REMOVE SPEEDOMETER SENSOR (w/o ABS) |
Remove the bolt and speedometer sensor from the transaxle case.
| 5. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY |
![]() |
Separate the back-up light switch wire harness from the 2 clamps.
Using SST, remove the back-up light switch assembly and gasket from the manual transmission case.
| 6. REMOVE SELECTING BELL CRANK ASSEMBLY |
![]() |
Remove the 2 bolts and nut and remove the selecting bell crank assembly from the manual transmission case.
Remove the control shift lever bush.
| 7. REMOVE FLOOR SHIFT CONTROL SHIFT LEVER |
![]() |
Remove the nut and spring washer.
![]() |
Using a brass bar and a hammer, remove the lock pin.
Remove the floor shift control shift lever.
| 8. REMOVE SHIFT LEVER DAMPER |
![]() |
Remove the nut and spring washer.
![]() |
Using a brass bar and a hammer, remove the lock pin.
Remove the shift lever damper.
| 9. FIX MANUAL TRANSAXLE ASSEMBLY |
![]() |
Place the manual transaxle assembly on wooden blocks.
| 10. REMOVE LOCK BALL ASSEMBLY NO.1 |
![]() |
Remove lock ball assembly No. 1 from the manual transmission case.
| 11. REMOVE SHIFT GATE PIN |
![]() |
Remove the shift gate pin and washer from the transmission case.
| 12. REMOVE CONTROL SHAFT COVER |
![]() |
Remove the 4 bolts, control shaft cover and gasket from the manual transmission case.
| 13. REMOVE CONTROL SHAFT COVER OIL SEAL |
![]() |
Using a screwdriver, remove the control shaft cover oil seal from the control shaft cover.
| 14. REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY |
![]() |
Remove the shift and select lever shaft assembly from the transmission case.
| 15. REMOVE MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY |
![]() |
Remove the 9 bolts.
![]() |
Using a plastic hammer, carefully tap the projection of the manual transmission case cover sub-assembly to remove the manual transmission case cover from the manual transmission case.
| 16. REMOVE MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT |
![]() |
Using a chisel and a hammer, loosen the staked part of the manual transmission output shaft rear set nut.
![]() |
Engage the 2 gears simultaneously to lock the transmission.
Remove the manual transmission output shaft rear set nut.
Disengage the 2 gears.
| 17. REMOVE GEAR SHIFT FORK NO.3 |
![]() |
Remove the gear shift fork lock bolt from gear shift fork No. 3.
![]() |
Remove transmission hub sleeve No. 3 with gear shift fork No. 3 from transmission clutch hub No. 3.
| 18. INSPECT 5TH GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the 5th gear thrust clearance.
| 19. INSPECT 5TH GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the 5th gear radial clearance.
| 20. REMOVE TRANSMISSION CLUTCH HUB NO. 3 |
![]() |
Using 2 screwdrivers and a hammer, tap out the snap ring.
![]() |
Using a screwdriver, remove the synchromesh shifting key spring from the transmission clutch hub No. 3.
![]() |
Using SST, remove the transmission clutch hub No. 3, 5th gear, and synchronizer ring No. 3 from the input shaft.
![]() |
Remove the 3 synchromesh shifting keys and synchromesh shifting key spring from the transmission clutch hub No. 3.
| 21. REMOVE 5TH GEAR NEEDLE ROLLER BEARING |
![]() |
Remove the 5th gear needle roller bearing and 5th gear bearing spacer from the input shaft.
| 22. REMOVE 5TH DRIVEN GEAR |
![]() |
Using SST, remove the 5th driven gear from the output shaft.
| 23. REMOVE BEARING RETAINER REAR |
![]() |
Remove the 5 bolts and bearing retainer rear from the manual transmission case.
| 24. REMOVE OUTPUT SHAFT REAR BEARING HOLE SNAP RING |
![]() |
Using a snap ring expander, remove the output shaft rear bearing hole snap ring from the output shaft.
| 25. REMOVE INPUT SHAFT REAR BEARING HOLE SNAP RING |
![]() |
Using a snap ring expander, remove the input shaft rear bearing hole snap ring from the input shaft.
| 26. REMOVE REVERSE IDLER GEAR SHAFT BOLT |
![]() |
Remove the reverse idler gear shaft bolt and reverse idler gear shaft gasket from the manual transmission case.
| 27. REMOVE SHIFT FORK SHAFT SHAFT SNAP RING |
![]() |
Using 2 screwdrivers and a hammer, tap out the snap ring from gear shift fork shaft No. 2.
| 28. REMOVE SHIFT DETENT BALL |
![]() |
Using a hexagon wrench, remove the 2 shift detent ball plugs from the manual transmission case.
![]() |
Using a magnetic finger, remove the 2 shift detent ball spring seats No. 1, 2 shift detent ball springs and 2 shift detent balls from the manual transmission case.
![]() |
Using a hexagon wrench, remove the shift detent ball plug from the front transaxle case.
![]() |
Using a magnetic finger, remove the seat, spring and ball from the front transaxle case.
| 29. REMOVE LOCK BALL ASSEMBLY NO.2 |
![]() |
Using a hexagon wrench, remove lock ball assembly No. 2 from the manual transmission case.
| 30. REMOVE MANUAL TRANSMISSION CASE |
![]() |
Remove the 3 bolts from the front transaxle case.
![]() |
Remove the 13 bolts from the manual transmission case.
![]() |
Using a brass bar and a hammer, carefully tap the projections of the manual transmission case to remove the transmission case from the transaxle case.
| 31. REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY |
![]() |
Remove the reverse idler gear sub-assembly, thrust washer and reverse idler gear shaft from the front transaxle case.
| 32. REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY |
![]() |
Remove the 2 bolts and reverse shift arm bracket assembly from the front transaxle case.
| 33. REMOVE GEAR SHIFT FORK SHAFT NO.2 |
![]() |
Remove the 2 bolts from gear shift fork No. 2 and gear shift head No. 1.
![]() |
Remove gear shift fork shaft No. 2 and gear shift head No. 1 from the front transaxle case.
| 34. REMOVE GEAR SHIFT FORK SHAFT NO.1 |
![]() |
Using 2 screwdrivers and a hammer, tap out the snap ring.
![]() |
Remove the shift fork set bolt and gear shift fork shaft No. 1 from gear shift fork No. 1.
![]() |
Remove gear shift fork No. 1.
| 35. REMOVE GEAR SHIFT FORK SHAFT NO.3 |
![]() |
Using 2 screwdrivers and a hammer, tap out the snap ring from gear shift fork shaft No. 3.
![]() |
Remove shift fork shaft No. 3 together with the reverse shift fork and gear shift fork No. 2 from the manual transaxle case.
![]() |
Using a magnetic finger, remove the 2 reverse shift fork balls from the reverse shift fork.
![]() |
Using 2 screwdrivers and a hammer, tap the snap ring out of shift fork shaft No. 3.
Remove the reverse shift fork from gear shift fork shaft No. 3.
| 36. REMOVE INPUT SHAFT ASSEMBLY |
![]() |
Remove the input shaft assembly and output shaft assembly from the front transaxle case.
| 37. REMOVE DIFFERENTIAL CASE ASSEMBLY |
![]() |
Remove the differential case assembly from the front transaxle case.
| 38. REMOVE MANUAL TRANSAXLE CASE RECEIVER |
![]() |
Remove the bolt and manual transaxle case receiver from the front transaxle case.
| 39. REMOVE REVERSE RESTRICT PIN ASSEMBLY |
![]() |
Using a hexagon wrench, remove the reverse restrict pin plug from the manual transmission case.
![]() |
Using a pin punch (φ5 mm) and a hammer, drive out the slotted spring pin and remove the reverse restrict pin assembly from the manual transmission case.
| 40. REMOVE OIL RECEIVER PIPE NO. 1 |
![]() |
Remove the bolt and oil receiver pipe No. 1 from the manual transmission case.
| 41. REMOVE OIL RECEIVER PIPE NO. 2 |
![]() |
Remove the bolt and oil receiver pipe No. 2 from the manual transmission case.
| 42. REMOVE BEARING LOCK PLATE |
![]() |
Remove the bolt and bearing lock plate from the front transaxle case.
| 43. REMOVE TRANSMISSION MAGNET |
![]() |
Remove the transmission magnet from the front transaxle case.
| 44. REMOVE INPUT SHAFT FRONT BEARING |
![]() |
Using SST, remove the input shaft front bearing from the front transaxle case.
| 45. REMOVE FRONT TRANSAXLE CASE OIL SEAL |
![]() |
Using a screwdriver, remove the front transaxle case oil seal from the transaxle case.
| 46. REMOVE OUTPUT SHAFT FRONT BEARING |
![]() |
Using SST, remove the output shaft front bearing from the front transaxle case.
| 47. REMOVE OUTPUT SHAFT COVER |
![]() |
Remove the output shaft cover from the front transaxle case.
| 48. REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING |
![]() |
Using SST, remove the front differential case front tapered roller bearing (outer race) and plate washer from the front transaxle case.
![]() |
Using SST, remove the front differential case front tapered roller bearing (inner race) from the differential case assembly.
| 49. REMOVE TRANSAXLE CASE OIL SEAL |
![]() |
Using SST and a hammer, remove the transaxle case oil seal from the front transaxle case.
| 50. REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING |
![]() |
Using SST, remove the front differential case rear tapered roller bearing (outer race) and plate washer from the transmission case.
![]() |
Using SST, remove the front differential case rear tapered roller bearing (inner race) from the front differential case.
| 51. REMOVE TRANSMISSION CASE OIL SEAL |
![]() |
Using SST and a hammer, drive out the transmission case oil seal from the manual transmission case.
| 52. REMOVE SHIFT AND SELECT LEVER SHAFT OIL SEAL |
![]() |
Using a screwdriver and hammer, remove the shift and select lever shaft oil seal.
| 53. REMOVE SHIFT AND SELECT LEVER SHAFT SLIDE BALL BEARING |
![]() |
Using SST and a hammer, remove the shift and select lever shaft slide ball bearing.