MANUAL TRANSAXLE UNIT (for Hatchback) > DISASSEMBLY |
| 1. REMOVE MANUAL TRANSMISSION FILLER PLUG |
![]() |
Remove the manual transmission filler plug and gasket from the manual transmission case.
| 2. REMOVE DRAIN PLUG SUB-ASSEMBLY |
![]() |
Remove the drain plug sub-assembly and gasket from the manual transmission case.
| 3. REMOVE BACK UP LIGHT SWITCH ASSEMBLY |
![]() |
Separate the back up light switch wire harness from the 2 clamps.
Using SST, remove the back up light switch assembly and gasket from the manual transmission case.
| 4. REMOVE SELECTING BELL CRANK ASSEMBLY |
![]() |
Remove the 2 bolts and nut and remove the selecting bell crank assembly from the manual transmission case.
Remove the control bell crank dust cover.
| 5. REMOVE FLOOR SHIFT CONTROL SHIFT LEVER |
![]() |
Remove the nut and spring washer.
![]() |
Using a brass bar and a hammer, remove the lock pin.
Remove the floor shift control shift lever and dust boot.
| 6. REMOVE SHIFT LEVER DAMPER |
![]() |
Remove the nut and spring washer.
![]() |
Using a brass bar and a hammer, remove the lock pin.
Remove the shift lever damper and dust boot.
| 7. FIX MANUAL TRANSAXLE ASSEMBLY |
![]() |
Place the manual transaxle assembly on wooden blocks.
| *1 | Wooden Block |
| 8. REMOVE NO. 1 LOCK BALL ASSEMBLY |
![]() |
Remove the No. 1 lock ball assembly from the manual transmission case.
| 9. REMOVE SHIFT GATE PIN |
![]() |
Remove the shift gate pin and washer from the manual transmission case.
| 10. REMOVE CONTROL SHAFT COVER |
![]() |
Remove the 4 bolts, control shaft cover and gasket from the manual transmission case.
| 11. REMOVE CONTROL SHAFT COVER OIL SEAL |
![]() |
Using a screwdriver, remove the control shaft cover oil seal from the control shaft cover.
| 12. REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY |
![]() |
Remove the shift and select lever shaft assembly from the manual transmission case.
| 13. REMOVE MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY |
![]() |
Remove the 9 bolts.
![]() |
Using a plastic hammer, carefully tap the projection of the manual transmission case cover sub-assembly to remove the manual transmission case cover sub-assembly from the manual transmission case.
![]() | Projection Part |
| 14. REMOVE MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT |
![]() |
Using a chisel and a hammer, loosen the staked part of the manual transmission output shaft rear set nut.
![]() |
Engage the 2 gears simultaneously to lock the transmission.
Remove the manual transmission output shaft rear set nut.
Disengage the 2 gears.
| 15. REMOVE NO. 3 GEAR SHIFT FORK |
![]() |
Remove the shift fork set bolt from the No. 3 gear shift fork.
![]() |
Remove the No. 3 transmission hub sleeve with the No. 3 gear shift fork from the No. 3 transmission clutch hub.
| 16. INSPECT 5TH GEAR THRUST CLEARANCE |
![]() |
Using a dial indicator, measure the 5th gear thrust clearance.
| 17. INSPECT 5TH GEAR RADIAL CLEARANCE |
![]() |
Using a dial indicator, measure the 5th gear radial clearance.
| 18. REMOVE NO. 3 TRANSMISSION CLUTCH HUB |
![]() |
Using 2 screwdrivers and a hammer, tap out the No. 3 clutch hub shaft snap ring.
![]() |
Using a screwdriver, remove the synchromesh shifting key spring from the No. 3 transmission clutch hub.
![]() |
Using SST, remove the No. 3 transmission clutch hub, 5th gear, and the No. 3 synchronizer ring from the input shaft assembly.
![]() |
Remove the 3 synchromesh shifting keys and synchromesh shifting key spring from the No. 3 transmission clutch hub.
| 19. REMOVE 5TH GEAR NEEDLE ROLLER BEARING |
![]() |
Remove the 5th gear needle roller bearing and 5th gear bearing spacer from the input shaft assembly.
| 20. REMOVE 5TH DRIVEN GEAR |
![]() |
Using SST, remove the 5th driven gear from the output shaft assembly.
| 21. REMOVE REAR BEARING RETAINER |
![]() |
Remove the 5 bolts and rear bearing retainer from the manual transmission case.
| 22. REMOVE OUTPUT SHAFT REAR BEARING HOLE SNAP RING |
![]() |
Using a snap ring expander, remove the output shaft rear bearing hole snap ring from the output shaft assembly.
| 23. REMOVE INPUT SHAFT REAR BEARING HOLE SNAP RING |
![]() |
Using a snap ring expander, remove the input shaft rear bearing hole snap ring from the input shaft assembly.
| 24. REMOVE REVERSE IDLER GEAR SHAFT BOLT |
![]() |
Remove the reverse idler gear shaft bolt and gasket from the manual transmission case.
| 25. REMOVE SHIFT FORK SHAFT SHAFT SNAP RING |
![]() |
Using 2 screwdrivers and a hammer, tap out the shift fork shaft shaft snap ring from the No. 2 gear shift fork shaft.
| 26. REMOVE SHIFT DETENT BALL |
![]() |
Using a hexagon wrench, remove the 2 shift detent ball plugs from the manual transmission case.
![]() |
Using a magnetic finger, remove the 2 spring seats, the compression springs and 2 shift detent balls from the manual transmission case.
![]() |
Using a hexagon wrench, remove the shift detent ball plug from the front transaxle case.
![]() |
Using a magnetic finger, remove the spring seat, compression spring and shift detent ball from the front transaxle case.
| 27. REMOVE NO. 2 LOCK BALL ASSEMBLY |
![]() |
Using a hexagon wrench, remove the No. 2 lock ball assembly from the manual transmission case.
| 28. REMOVE MANUAL TRANSMISSION CASE |
![]() |
Remove the 3 bolts from the front transaxle case.
![]() |
Remove the 13 bolts from the manual transmission case.
![]() |
Using a brass bar and a hammer, carefully tap the projections of the manual transmission case to remove the manual transmission case from the transaxle case.
| 29. REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY |
![]() |
Remove the reverse idler gear sub-assembly, reverse idler thrust washer and reverse idler gear shaft from the front transaxle case.
| 30. REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY |
![]() |
Remove the 2 bolts and reverse shift arm bracket assembly from the front transaxle case.
| 31. REMOVE NO. 2 GEAR SHIFT FORK SHAFT |
![]() |
Remove the 2 shift fork set bolts from the No. 2 gear shift fork and the No. 1 gear shift head.
![]() |
Remove the No. 2 gear shift fork shaft and the No. 1 gear shift head from the front transaxle case.
| *1 | No. 2 Gear Shift Fork Shaft |
| *2 | No. 1 Gear Shift Head |
| 32. REMOVE NO. 1 GEAR SHIFT FORK SHAFT |
![]() |
Using 2 screwdrivers and a hammer, tap out the snap ring.
![]() |
Remove the shift fork set bolt and the No. 1 gear shift fork shaft from the No. 1 gear shift fork.
| *1 | No. 1 Gear Shift Fork Shaft |
![]() |
Remove the No. 1 gear shift fork.
| *1 | No. 1 Gear Shift Fork |
| 33. REMOVE NO. 3 GEAR SHIFT FORK SHAFT |
![]() |
Using 2 screwdrivers and a hammer, tap out the snap ring from the No. 3 gear shift fork shaft.
![]() |
Remove the No. 3 gear shift fork shaft together with the reverse shift fork and the No. 2 gear shift fork from the front transaxle case.
| *1 | No. 2 Gear Shift Fork |
| *2 | No. 3 Gear Shift Fork Shaft |
| *3 | Reverse Shift Fork |
![]() |
Using a magnetic finger, remove the 2 reverse shift fork balls from the reverse shift fork.
![]() |
Using 2 screwdrivers and a hammer, tap the snap ring out of the No. 3 shift fork shaft.
Remove the reverse shift fork from the No. 3 gear shift fork shaft.
| 34. REMOVE INPUT SHAFT ASSEMBLY |
![]() |
Remove the input shaft assembly and output shaft assembly from the front transaxle case.
| 35. REMOVE DIFFERENTIAL CASE ASSEMBLY |
![]() |
Remove the differential case assembly from the front transaxle case.
| 36. REMOVE MANUAL TRANSAXLE CASE RECEIVER |
![]() |
Remove the bolt and manual transaxle case receiver from the front transaxle case.
| 37. REMOVE REVERSE RESTRICT PIN ASSEMBLY |
![]() |
Using a hexagon wrench, remove the reverse restrict pin plug from the manual transmission case.
![]() |
Using a pin punch (φ5 mm) and a hammer, drive out the slotted spring pin and remove the reverse restrict pin assembly from the manual transmission case.
| 38. REMOVE NO. 1 OIL RECEIVER PIPE |
![]() |
Remove the bolt and the No. 1 oil receiver pipe from the manual transmission case.
| 39. REMOVE NO. 2 OIL RECEIVER PIPE |
![]() |
Remove the bolt and the No. 2 oil receiver pipe from the manual transmission case.
| 40. REMOVE BEARING LOCK PLATE |
![]() |
Remove the bolt and bearing lock plate from the front transaxle case.
| 41. REMOVE TRANSMISSION MAGNET |
![]() |
Remove the transmission magnet from the front transaxle case.
| 42. REMOVE INPUT SHAFT FRONT BEARING |
![]() |
Using SST, remove the input shaft front bearing from the front transaxle case.
| 43. REMOVE FRONT TRANSAXLE CASE OIL SEAL |
![]() |
Using a screwdriver, remove the front transaxle case oil seal from the front transaxle case.
| 44. REMOVE OUTPUT SHAFT FRONT BEARING |
![]() |
Using SST, remove the output shaft front bearing from the front transaxle case.
| 45. REMOVE OUTPUT SHAFT COVER |
![]() |
Remove the output shaft cover from the front transaxle case.
| 46. REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING |
![]() |
Using SST, remove the front differential case front tapered roller bearing (outer race) and front differential case front plate washer from the front transaxle case.
![]() |
Using SST, remove the front differential case front tapered roller bearing (inner race) from the differential case assembly.
| 47. REMOVE TRANSAXLE CASE OIL SEAL |
![]() |
Using SST and a hammer, remove the transaxle case oil seal from the front transaxle case.
| 48. REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING |
![]() |
Using SST, remove the front differential case rear tapered roller bearing (outer race) and front differential case rear plate washer from the manual transmission case.
![]() |
Using SST, remove the front differential case rear tapered roller bearing (inner race) from the differential case assembly.
| 49. REMOVE TRANSMISSION CASE OIL SEAL |
![]() |
Using SST and a hammer, drive out the transmission case oil seal from the manual transmission case.
| 50. REMOVE SHIFT AND SELECT LEVER SHAFT OIL SEAL |
![]() |
Using a screwdriver and hammer, remove the shift and select lever shaft oil seal.
| 51. REMOVE SHIFT AND SELECT LEVER SHAFT SLIDE BALL BEARING |
![]() |
Using SST and a hammer, remove the shift and select lever shaft slide ball bearing.