Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (for Hatchback)

LIGHTING SYSTEM (for Hatchback) > Low Beam Headlight Circuit


DESCRIPTION

The main body ECU controls the low beam headlights.

WIRING DIAGRAM


E231964E04


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Headlight Relay
    Running light relay
    OFF or ON
    -

    OK:
    Running light relay operates. (Low beam headlights illuminate.)



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK HEADLIGHT
  1. Check the operation of the high beam headlights.

    OK:
    High beam headlights operate normally.



NG
GO TO PROBLEM SYMPTOMS TABLE (Click here)
OK


3.INSPECT RUNNING LIGHT RELAY
  1. Remove the running light relay from the No. 2 engine room relay block.



    E229351E02
  1. Connect the positive (+) lead from the battery to terminal 6 (+B).

  1. Connect the negative (-) lead from the battery to terminal 4 (H) and 3 (E).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1 (HLOR) - Battery negative terminal
    Always
    11 to 14 V
    5 (HLOL) - Battery negative terminal
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Component without harness connected
    (Running Light Relay)



NG
REPLACE RUNNING LIGHT RELAY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (RUNNING LIGHT RELAY - HEADLIGHT DIMMER RELAY AND BODY GROUND)


    E229353E01
  1. Remove the running light relay from the No. 2 engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    DRL-6 (+B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DRL-3 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block
    *2
    Running Light Relay Terminal



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (RUNNING LIGHT RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Remove the running light relay from the No. 2 engine room relay block assembly.

  1. Disconnect the 3C instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DRL-4 (H) - 3C-18
    Always
    Below 1 Ω
    DRL-4 (H) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly.

  1. Remove the main body ECU from the instrument panel junction block assembly.



  1. Measure the resistance according to the value(s) in the table below.


    E231963E04


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3C-18 - MB-15 (HRLY)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

REPLACE MAIN BODY ECU (Click here)