Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER (for Sedan)

FRONT SHOCK ABSORBER (for Sedan) > REMOVAL

for Preparation Click here



1. REMOVE FRONT WIPER ARM HEAD CAP


    E127832E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.



2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E127833
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. Remove the nut and front wiper arm.



3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



4. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    E127834E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.



5. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E127838
  1. Disengage the 3 clips, the 4 claws and the 8 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.



    E127839
  1. Disconnect the washer hoses.

  1. Disengage the 5 hooks.



7. REMOVE FRONT WIPER MOTOR AND LINK


    E127837
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.



8. REMOVE FRONT AIR SHUTTER SEAL


A133324
  1. Disengage the 3 claws and remove the front air shutter seal RH.



9. REMOVE OUTER COWL TOP PANEL


    A128446
  1. Disengage the wire harness clamp.



    A128447
  1. Remove the 2 bolts and remove the cowl top to cowl inner brace.



    A128448
  1. Remove the 8 bolts and remove the cowl top panel outer.



10. REMOVE FRONT WHEEL


11. SEPARATE FRONT STABILIZER LINK ASSEMBLY


    C125276
  1. Remove the nut and separate the front stabilizer link assembly from the front shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 mm to hold the stud.



12. SEPARATE FRONT FLEXIBLE HOSE (w/ ABS)


    C125274
  1. Remove the bolt and separate the front speed sensor and the front flexible hose.



13. SEPARATE FRONT FLEXIBLE HOSE (w/o ABS)
  1. Remove the bolt and separate the front flexible hose.



14. REMOVE FRONT SUSPENSION SUPPORT DUST COVER


15. REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING


    C125277
  1. Remove the 2 nuts and 2 bolts and separate the front shock absorber with coil spring from the steering knuckle.

    HINT:
    Keep the bolt from rotating while loosening and removing the nuts.



    C107504
  1. Using a socket hexagon wrench 6 mm, fix the front shock absorber rod and remove the nut.

  1. Remove No. 2 suspension support.

  1. Remove the front shock absorber with coil spring from the vehicle.



16. REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY


17. REMOVE FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT


    C107505E02
  1. Using a socket hexagon wrench 6 mm, hold the front shock absorber rod and loosen the front support to front shock absorber nut.
    Text in Illustration 
    *a
    Turn
    *b
    Hold



    C107506E01
  1. Secure SST in a vise.

    SST
    09727-30021   (09727-00010, 09727-00021, 09727-00031)



    C275706E03
  1. Attach the arm of SST to the diameter of the front coil spring.
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect

    CAUTION:
    1. Make sure that the front coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.
    2. Make sure that the claws of the hooks are securely attached.

  1. Using SST, compress the front coil spring.

    CAUTION:
    1. If the front coil spring bends during the compression, immediately stop the compression and reinstall SST.
    2. Do not compress the spring until the coil springs contact each other.
    3. Do not use an impact wrench. It will damage SST.

  1. Confirm that the front coil spring becomes free and remove the front support to front shock absorber nut.

    CAUTION:
    1. Do not remove the nut when the front coil spring is not free.



18. REMOVE FRONT UPPER COIL SPRING SEAT
  1. Remove the front upper coil spring seat with the strut mounting bearing and the front spring bumper from the front shock absorber.



19. REMOVE FRONT SPRING BUMPER
  1. Remove the front spring bumper from the front upper coil spring seat.



20. REMOVE FRONT UPPER COIL SPRING INSULATOR


21. REMOVE FRONT COIL SPRING


22. REMOVE STRUT MOUNTING BEARING


    C112822
  1. Using a brass bar and press, remove the strut mounting bearing from the front upper coil spring seat.