DTC C1511/11 Torque Sensor 1 Malfunction |
DTC C1512/12 Torque Sensor Circuit Malfunction |
DTC C1513/13 Torque Sensor Circuit Malfunction |
DTC C1514/14 Torque Sensor Power Source Circuit Malfunction |
DTC C1517/17 Torque Sensor Hold Malfunction |
| DTC No. | Detection Item | Trouble Area |
| C1511/11 | Torque sensor (TRQ1) signal error or stop |
|
| C1512/12 | Torque sensor (TRQ2) signal error or stop | |
| C1513/13 | Deviation between torque sensor TRQ1 and TRQ2 exceeds specified value | |
| C1514/14 | Torque sensor power source voltage error | |
| C1517/17 | Temporary control due to malfunction related to torque sensor continues for long time |

| 1.READ VALUE USING TECHSTREAM |
Connect a Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Chassis / EMPS / Data List.
Select the items "Torque Sensor 1 Output" and "Torque Sensor 2 Output" in the Data List and read the value displayed on the Techstream.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Torque Sensor 1 Output | Torque sensor 1 voltage: Minimum: 0.0000 V, Maximum: 5.0000 V | 2.3 to 2.7 V: Steering wheel not turned (without load) | Read value with vehicle stopped |
| 2.5 to 4.7 V: Steering wheel turned to right | Read value with vehicle stopped | ||
| 0.3 to 2.5 V: Steering wheel turned to left | Read value with vehicle stopped | ||
| Torque Sensor 2 Output | Torque sensor 2 voltage: Minimum: 0.0000 V, Maximum: 5.0000 V | 2.3 to 2.7 V: Steering wheel not turned (without load) | Read value with vehicle stopped |
| 2.5 to 4.7 V: Steering wheel turned to right | Read value with vehicle stopped | ||
| 0.3 to 2.5 V: Steering wheel turned to left | Read value with vehicle stopped |
Check the difference in the values between "Torque Sensor 1 Output" and "Torque Sensor 2 Output".
|
| ||||
| NG | |
| 2.INSPECT POWER STEERING ECU (OUTPUT) |
![]() |
Turn the ignition switch to ON.
Measure the voltage.
| Tester Connection | Condition | Specified condition |
| TRQV (c1-6) - TRQG (c1-8) | Ignition switch on | 7.5 to 8.5 V |
|
| ||||
| OK | |
| 3.INSPECT STEERING COLUMN ASSEMBLY (TORQUE SENSOR) |
![]() |
Turn the ignition switch to ON.
Measure the voltage.
| Tester Connection | Condition (Steering Position) | Specified Condition |
| TRQ1 (c1-5) - TRQG (c1-8) | Center position | 2.3 to 2.7 V |
| TRQ2 (c1-7) - TRQG (c1-8) | Center position | 2.3 to 2.7 V |
| TRQ1 (c1-5) - TRQG (c1-8) | Turned to right | 2.5 to 4.7 V |
| TRQ2 (c1-7) - TRQG (c1-8) | Turned to right | 2.5 to 4.7 V |
| TRQ1 (c1-5) - TRQG (c1-8) | Turned to left | 0.3 to 2.5 V |
| TRQ2 (c1-7) - TRQG (c1-8) | Turned to left | 0.3 to 2.5 V |
|
| ||||
| OK | ||
| ||