FRONT LOWER SUSPENSION ARM (for Sedan RH Side) > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE HOOD SUB-ASSEMBLY |
Remove the 4 bolts and remove the hood.
| 3. REMOVE FRONT WIPER ARM HEAD CAP |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.
| 4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Remove the nut and front wiper arm.
| 5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH |
| 6. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.
| 7. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH |
| 8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() |
Disengage the 3 clips, the 4 claws and the 8 hooks.
Remove the cowl top ventilator louver sub-assembly.
![]() |
Disconnect the washer hoses.
Disengage the 5 hooks.
| 9. REMOVE FRONT WIPER MOTOR AND LINK |
![]() |
Remove the 2 bolts.
Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.
| 10. REMOVE FRONT AIR SHUTTER SEAL |
![]() |
Disengage the 3 claws and remove the front air shutter seal RH.
| 11. REMOVE OUTER COWL TOP PANEL |
![]() |
Disengage the wire harness clamp.
![]() |
Remove the 2 bolts and remove the cowl top to cowl inner brace.
![]() |
Remove the 8 bolts and remove the cowl top panel outer.
| 12. POSITION WHEELS FACING STRAIGHT AHEAD |
| 13. REMOVE FRONT WHEEL |
| 14. REMOVE COLUMN HOLE COVER SILENCER SHEET |
![]() |
Pull back the floor carpet, remove the 2 clips and remove the column hole cover silencer sheet.
| 15. REMOVE STEERING SLIDING YOKE SUB-ASSEMBLY |
![]() |
Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.
![]() |
Place matchmarks on the sliding yoke of the steering intermediate shaft assembly and the steering gear assembly.
| *1 | Bolt A |
| *2 | Bolt B |
| *a | Matchmark |
Loosen bolt A, remove bolt B and separate the steering intermediate shaft assembly.
| 16. REMOVE STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
![]() |
Remove clip A, separate clip B from the body and separate No. 1 steering column hole cover sub-assembly.
| *1 | Clip A |
| *2 | Clip B |
| 17. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH |
![]() |
Remove the nut and separate the front stabilizer link assembly from the front shock absorber.
| 18. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH |
| 19. SEPARATE TIE ROD END SUB-ASSEMBLY LH |
Remove the cotter pin and castle nut.
![]() |
Using SST, separate the tie rod end from the steering knuckle.
| 20. SEPARATE TIE ROD END SUB-ASSEMBLY RH |
| 21. SEPARATE FRONT LOWER SUSPENSION ARM LH |
![]() |
Remove the clip and castle nut.
![]() |
Using SST, separate the lower arm.
![]() |
Remove the 2 bolts and lower arm.
| 22. SEPARATE FRONT LOWER SUSPENSION ARM RH |
| 23. SUSPEND ENGINE ASSEMBLY |
Remove the bolt and remove the radio setting condenser.
Remove the bolt and remove the air-fuel ratio sensor wiring bracket.
![]() |
Install the engine hanger with the bolt in the position shown in the illustration.
| *a | Front Side |
| *b | Rear Side |
| Engine Hanger | 12281-21010 |
| Bolt | 91642-81025 |
Using an engine sling device and a chain block, support the engine assembly w/transaxle and front suspension crossmember.
| 24. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
![]() |
Remove the bolt and separate the engine moving control rod.
![]() |
Place wooden blocks or plate lift attachments in the positions shown in the illustration and set an engine lifter underneath the front suspension crossmember sub-assembly.
![]() | Front of the Vehicle |
![]() | Attachment Placement Positions |
![]() |
Remove the 6 bolts and the front suspension crossmember sub-assembly.
| 25. REMOVE FRONT LOWER SUSPENSION ARM RH |
![]() |
Remove the bolt and lower arm.