Home › Suspension › FRONT SUSPENSION › FRONT STABILIZER BAR (for Sedan)

FRONT STABILIZER BAR (for Sedan) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE HOOD SUB-ASSEMBLY
  1. Remove the 4 bolts and remove the hood.



3. REMOVE FRONT WIPER ARM HEAD CAP


    E127832E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.



4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E127833
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. Remove the nut and front wiper arm.



5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



6. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    E127834E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.



7. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E127838
  1. Disengage the 3 clips, the 4 claws and the 8 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.



    E127839
  1. Disconnect the washer hoses.

  1. Disengage the 5 hooks.



9. REMOVE FRONT WIPER MOTOR AND LINK


    E127837
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.



10. REMOVE FRONT AIR SHUTTER SEAL


A133324
  1. Disengage the 3 claws and remove the front air shutter seal RH.



11. REMOVE OUTER COWL TOP PANEL


    A128446
  1. Disengage the wire harness clamp.



    A128447
  1. Remove the 2 bolts and remove the cowl top to cowl inner brace.



    A128448
  1. Remove the 8 bolts and remove the cowl top panel outer.



12. POSITION WHEELS FACING STRAIGHT AHEAD


13. REMOVE FRONT WHEEL


14. REMOVE COLUMN HOLE COVER SILENCER SHEET


    A116501
  1. Pull back the floor carpet, remove the 2 clips and remove the column hole cover silencer sheet.



15. REMOVE STEERING SLIDING YOKE SUB-ASSEMBLY


    C139107
  1. Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.



    C118005E08
  1. Place matchmarks on the sliding yoke of the steering intermediate shaft assembly and the steering gear assembly.
    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *a
    Matchmark

  1. Loosen bolt A, remove bolt B and separate the steering intermediate shaft assembly.



16. REMOVE STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    C139112E02
  1. Remove clip A, separate clip B from the body and separate No. 1 steering column hole cover sub-assembly.
    Text in Illustration 
    *1
    Clip A
    *2
    Clip B



17. REMOVE FRONT STABILIZER LINK ASSEMBLY LH


    C125276
  1. Remove the nut and separate the front stabilizer link assembly from the front shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 mm to hold the stud.



18. REMOVE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.



19. SEPARATE TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.



    C116895E01
  1. Using SST, separate the tie rod end from the steering knuckle.

    SST
    09628-62011  

    NOTICE:
    Do not damage the tie rod end dust cover.



20. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.



21. SEPARATE FRONT LOWER SUSPENSION ARM LH


C107513
  1. Remove the clip and castle nut.



    C107514E01
  1. Using SST, separate the lower arm.

    SST
    09628-00011  

    NOTICE:
    1. Do not damage the lower arm dust cover.
    2. Suspend SST with a piece of string or the equivalent.



    C107515
  1. Remove the 2 bolts and lower arm.



22. SEPARATE FRONT LOWER SUSPENSION ARM RH

HINT:
The removal procedure for the RH side is the same as that for the LH side.



23. SUSPEND ENGINE ASSEMBLY
  1. Remove the bolt and remove the radio setting condenser.

  1. Remove the bolt and remove the air-fuel ratio sensor wiring bracket.



    A070012E02
  1. Install the engine hanger with the bolt in the position shown in the illustration.
    Text in Illustration 
    *a
    Front Side
    *b
    Rear Side
    Part No. 
    Engine Hanger
    12281-21010
    Bolt
    91642-81025

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Using an engine sling device and a chain block, support the engine assembly w/transaxle and front suspension crossmember.



24. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


    C213131
  1. Remove the bolt and separate the engine moving control rod.



    C233132
  1. Place wooden blocks or plate lift attachments in the positions shown in the illustration and set an engine lifter underneath the front suspension crossmember sub-assembly.
    Text in Illustration 
    V100135
    Front of the Vehicle
    V100144
    Attachment Placement Positions

    NOTICE:
    1. Place the wooden blocks or plate lift attachments so that the front suspension crossmember sub-assembly is level.
    2. As the front suspension crossmember sub-assembly is very heavy, be sure to support it securely.



    A246188
  1. Remove the 6 bolts and the front suspension crossmember sub-assembly.



25. REMOVE POWER STEERING GEAR


C117189
  1. Remove the 2 bolts and 2 nuts and remove the steering gear assembly from the suspension crossmember.

    NOTICE:
    Keep the nut from rotating while turning the bolt.



26. REMOVE FRONT STABILIZER BRACKET LH


C116871
  1. Remove the 2 bolts and the stabilizer bracket.



27. REMOVE FRONT STABILIZER BRACKET RH
  1. Remove the 2 bolts and the stabilizer bracket.



28. REMOVE FRONT STABILIZER BAR


29. REMOVE FRONT STABILIZER BAR BUSH