Home › Drivetrain ยท C50 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE ASSEMBLY (for Sedan)

MANUAL TRANSAXLE ASSEMBLY (for Sedan) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE COLUMN HOLE COVER SILENCER SHEET


    A116501
  1. Pull back the floor carpet, remove the 2 clips and remove the column hole cover silencer sheet.



3. SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY


    C139107
  1. Use a seat belt to fix the steering wheel assembly, in order to avoid breakage of the spiral cable.



    C118005E08
  1. Place matchmarks on the sliding yoke of the steering intermediate shaft assembly and the steering gear assembly.
    Text in Illustration 
    *1
    Bolt A
    *2
    Bolt B
    *a
    Matchmark

  1. Loosen bolt A, remove bolt B and separate the steering intermediate shaft assembly.



4. REMOVE FRONT WHEELS


5. REMOVE ENGINE UNDER COVER LH


6. REMOVE ENGINE UNDER COVER RH


7. DRAIN TRANSAXLE OIL
  1. Remove the filler plug and the gasket.

  1. Remove the drain plug and the gasket, and then drain the manual transaxle oil.

  1. Install a new gasket and the drain plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



8. REMOVE HOOD SUB-ASSEMBLY
  1. Remove the 4 bolts and remove the hood.



9. REMOVE FRONT WIPER ARM HEAD CAP


    E127832E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.



10. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E127833
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. Remove the nut and front wiper arm.



11. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



12. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    E127834E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.



13. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



14. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E127838
  1. Disengage the 3 clips, the 4 claws and the 8 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.



    E127839
  1. Disconnect the washer hoses.

  1. Disengage the 5 hooks.



15. REMOVE WINDSHIELD WIPER MOTOR AND LINK


    E127837
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.



16. REMOVE FRONT AIR SHUTTER SEAL


A133324
  1. Disengage the 3 claws and remove the front air shutter seal RH.



17. REMOVE COWL TOP PANEL OUTER


    A128446
  1. Disengage the wire harness clamp.



    A128447
  1. Remove the 2 bolts and remove the cowl top to cowl inner brace.



    A128448
  1. Remove the 8 bolts and remove the cowl top panel outer.



18. REMOVE NO. 2 CYLINDER HEAD COVER


A116235
  1. Remove the 4 nuts and cylinder head cover No. 2.



19. REMOVE AIR CLEANER ASSEMBLY


A251683
  1. Separate the intake air flow meter connector and the wire harness clamp.

  1. Separate the fuel vapor feed hose from the vacuum switching valve assembly and air cleaner hose.

  1. Separate the vacuum switching valve connector and the wire harness clamp.

  1. Separate the ventilation hose from the air cleaner hose.

  1. Release the air cleaner cap sub-assembly with No. 1 air cleaner hose.

  1. Loosen the air cleaner hose clamp on the throttle body side and remove the air cleaner cap and the air cleaner hose.

  1. Remove the air cleaner element.



    A104895
  1. Separate the wire harness clamp from the air cleaner case.

  1. Remove the 2 bolts and remove the air cleaner case with No. 1 air cleaner inlet.



20. REMOVE AIR CLEANER BRACKET


C106369
  1. Remove the 2 bolts and the air cleaner bracket.



21. REMOVE BATTERY CLAMP SUB-ASSEMBLY


22. REMOVE BATTERY


23. REMOVE BATTERY TRAY


24. REMOVE BATTERY CARRIER


C106370
  1. Remove the 5 bolts and the battery carrier.



25. SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY


C106371
  1. Remove the 4 bolts, then separate the clutch release cylinder.

    HINT:
    Suspend the clutch release cylinder with a piece of rope so as not to overload the clutch pipe.



26. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY


C241507
  1. Remove the 2 clips and the 2 washers, and disconnect the 2 cables from the transaxle.

  1. Remove the 2 clips and disconnect the 2 cables from the control cable bracket.



27. REMOVE CONTROL CABLE BRACKET


C106374
  1. Remove the 2 bolts and the control cable bracket.



28. DISCONNECT WIRE HARNESS


C108079
  1. Remove the bolt, then disconnect the wire harness.



29. DISCONNECT CONNECTOR
  1. Disconnect the back-up light switch connector.



30. REMOVE STARTER ASSEMBLY


A104498
  1. Remove the terminal cap.

  1. Remove the nut and remove terminal 30.

  1. Disconnect the connector.

  1. Remove the 2 bolts and remove the starter assembly.



31. REMOVE FRONT AXLE SHAFT LH NUT


C085629E01
  1. Using SST and a hammer, release the staked part of the axle hub nut.

    SST
    09930-00010  

    NOTICE:
    1. Insert SST into the groove with the flat surface facing up.
    2. Do not damage the tip of SST using grinders.
    3. Completely unstake the staked part before removing the axle hub nut.
    4. Do not damage the threads of the drive shaft.

  1. Using a 30 mm socket wrench, remove the axle hub nut.



32. REMOVE FRONT AXLE SHAFT RH NUT

HINT:
The removal procedure for the RH side is the same as that for the LH side.



33. SEPARATE SPEED SENSOR FRONT LH (w/ ABS)


C125274
  1. Remove the bolt and separate the speed sensor and flexible hose.



    C112274
  1. Remove the bolt and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Keep the speed sensor tip and installation portion free of foreign matter.
    2. Remove the speed sensor without turning it from its original installation angle.



34. SEPARATE SPEED SENSOR FRONT RH (w/ ABS)

HINT:
The separation procedure for the RH side is the same as that for the LH side.



35. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH


    C125276
  1. Remove the nut and separate the front stabilizer link assembly from the front shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a socket hexagon wrench 6 mm to hold the stud.



36. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.



37. SEPARATE TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.



    C116895E01
  1. Using SST, separate the tie rod end from the steering knuckle.

    SST
    09628-62011  

    NOTICE:
    Do not damage the tie rod end dust cover.



38. SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.



39. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH


C107513
  1. Remove the clip and castle nut.



    C107514E01
  1. Using SST, separate the lower arm.

    SST
    09628-00011  

    NOTICE:
    1. Do not damage the lower ball joint dust cover.
    2. Suspend SST with a piece of string or the equivalent.



40. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.



41. SEPARATE FRONT AXLE ASSEMBLY LH
  1. Using a plastic hammer, tap the end of the drive shaft and disengage the fitting between the drive shaft and front axle.

    HINT:
    If it is difficult to disengage the fitting, tap the end of the drive shaft with a brass bar and hammer.

  1. Push the front axle out of the vehicle to remove the drive shaft from the front axle.

    NOTICE:
    1. Do not push the front axle further out of the vehicle than is necessary.
    2. Do not damage the outboard joint boot.
    3. Do not damage the speed sensor rotor.
    4. Suspend the drive shaft with a piece of string or the equivalent.



42. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
The separation procedure for the RH side is the same as that for the LH side.



43. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


C107924
  1. Using SST, remove the drive shaft.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.



44. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH


C116896
  1. Using a screwdriver and hammer, remove the drive shaft.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the inboard joint boot.
    3. Do not drop the drive shaft.



45. SUSPEND ENGINE ASSEMBLY


    D030284E03
  1. Install the 2 hangers in the correct direction.
    Text in Illustration 
    *a
    Front Side
    *b
    Rear Side

    Torque:
    40 N*m{ 408 kgf*cm , 29 ft.*lbf }

    HINT 
    Engine Hanger
    12281-21010
    Bolt
    91642-81025

  1. Attach the engine chain hoist to the hangers.

    CAUTION:
    Do not attempt to hang the engine by hooking the chain to any other part.



46. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


    C213131
  1. Remove the bolt and separate the engine moving control rod.



    C233132
  1. Place wooden blocks or plate lift attachments in the positions shown in the illustration and set an engine lifter underneath the front suspension crossmember sub-assembly.
    Text in Illustration 
    V100135
    Front of the Vehicle
    V100144
    Attachment Placement Positions

    NOTICE:
    1. Place the wooden blocks or plate lift attachments so that the front suspension crossmember sub-assembly is level.
    2. As the front suspension crossmember sub-assembly is very heavy, be sure to support it securely.



    A246188
  1. Remove the 6 bolts and the front suspension crossmember sub-assembly.



47. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING CONTROL BRACKET


C116856
  1. Remove the 4 bolts and the engine mounting control bracket.



48. SUPPORT MANUAL TRANSAXLE ASSEMBLY


49. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR


C106372
  1. Remove the bolt and nut, then separate the engine mounting insulator LH.

  1. Remove the 5 bolts and the engine mounting insulator LH.



50. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET


C121108
  1. Remove the 4 bolts and the engine mounting bracket LH.



51. REMOVE MANUAL TRANSAXLE ASSEMBLY


C063143
  1. Remove the 7 bolts and the manual transaxle.