Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT (for Sedan)

FRONT WHEEL ALIGNMENT (for Sedan) > ADJUSTMENT



1. INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold Tire Inflation Pressure:

    Tire Size
    Vehicle Speed
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    185/60R15 84H
    Driving below
    160 km/h (100 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving above
    160 km/h (100 mph)
    230 (2.3, 33)
    230 (2.3, 33)



    C164558
  1. Using a dial indicator, check the tire runout.

    Tire Runout:
    Vertical
    1.4 mm (0.0551 in.) or less
    Lateral
    2.0 mm (0.0787 in.) or less



2. MEASURE VEHICLE HEIGHT

NOTICE:
  1. Before inspecting the wheel alignment, check the vehicle height.
  2. Be sure to perform measurement on a level surface.
  3. If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.
  4. Inspect while the vehicle is unloaded.
  5. The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.



    C132096E03
  1. Measure the vehicle height.

    Vehicle Height (Unloaded Vehicle):
    A - B
    C - D
    67 mm (2.64 in.)
    -2 mm (-0.0787 in.)

    Measuring points:
    A:
    Ground clearance of front wheel center
    B:
    Ground clearance of lower arm set front bolt center
    C:
    Ground clearance of rear wheel center
    D:
    Ground clearance of axle beam set bolt center



3. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION


    C132440E28
  1. Put the front wheel on the center of the turning radius gauge.
    Text in Illustration 
    *a
    Turning Radius Gauge
    *b
    Camber-caster-kingpin Gauge

  1. Remove the wheel cap.

  1. Install the camber-caster-kingpin gauge at the center of the drive shaft.

  1. Inspect the camber, caster and steering axis inclination.

    Camber, Caster and Steering Axis Inclination (Unloaded Vehicle):

    Camber
    Caster
    Steering Axis Inclination
    (Reference)
    0°06' +/- 45' (0.10°+/- 0.75°)
    4°23' +/- 45' (4.38°+/- 0.75°)
    10°47' (10.78°)

    If the caster and steering axis inclination are not within the specified values after the camber has been correctly adjusted, recheck the suspension parts for damage and wear.

    NOTICE:
    1. Inspect while the vehicle is unloaded.
    2. The tolerance for the difference between the left and right wheels is 0°30' (0.5°) or less for both the camber and caster.

  1. Remove the camber-caster-kingpin gauge.

  1. Install the wheel cap.



4. ADJUST CAMBER

NOTICE:
Inspect the toe-in after the camber has been adjusted.

  1. Remove the front wheel.



  1. w/ ABS:



      C125274
    1. Remove the bolt and separate the front speed sensor and the front flexible hose.



    C125275
  1. Remove the 2 nuts from the lower side of the front shock absorber.

    HINT:
    Keep the bolt from rotating while loosening and removing the nuts.

  1. Clean the installation surfaces of the front shock absorber and the steering knuckle.

  1. Temporarily install the 2 nuts. (Step A)



    C205448E01
  1. Fully push or pull the axle hub in the direction of the required adjustment. (Step B)



    C125275
  1. Tighten the 2 nuts.

    Torque:
    164 N*m{ 1672 kgf*cm , 121 ft.*lbf }

    HINT:
    Keep the bolt from rotating while tightening and installing the nuts.



    C125274
  1. w/ ABS:

    1. Install the front flexible hose and the front speed sensor with the bolt.

      Torque:
      29 N*m{ 300 kgf*cm , 22 ft.*lbf }

      NOTICE:
      Install the front flexible hose and the front speed sensor without twisting them.

  1. Install the front wheel.

    Torque:
    103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



    C116741E02
  1. Check the camber.
    If the measured value is not within the specification, calculate the required adjustment amount using the formula below.
    (Camber adjustment amount) = Center of specified range - Measured value
    Check the combination of installed bolts. Select appropriate bolts from the table below to adjust the camber to within the specified range.

    HINT:
    Try to adjust the camber to the center of the specified range.

    Move axle toward (+) in step (B)
    Refer to table (1) (Move axle hub toward positive side)
    Move axle toward (-) in step (B)
    Refer to table (2) (Move axle hub toward negative side)



    1. Table (1) (Move the axle hub toward the positive side)


      C276380E03


      Text in Illustration 
      *a
      Table (1) (Move the axle hub toward the positive side)
      *b
      Installed Bolt
      *c
      Adjusting Value
      *d
      -1°30' to -1°15'
      *e
      -1°15' to -1°00'
      *f
      -1°00' to -0°45'
      *g
      -0°45' to -0°30'
      *h
      -0°30' to -0°15'
      *i
      -0°15' to 0°
      *j
      0° to 0°15'
      *k
      0°15' to 0°30'
      *l
      0°30' to 0°45'
      *m
      0°45' to 1°00'
      *n
      1°00' to 1°15'
      *o
      1°15' to 1°30'
      *p
      Selected Bolt Combination



    2. Table (2) (Move the axle hub toward the negative side)


      C276380E04


      Text in Illustration 
      *a
      Table (2) (Move the axle hub toward the negative side)
      *b
      Installed Bolt
      *c
      Adjusting Value
      *d
      -1°30' to -1°15'
      *e
      -1°15' to -1°00'
      *f
      -1°00' to -0°45'
      *g
      -0°45' to -0°30'
      *h
      -0°30' to -0°15'
      *i
      -0°15' to 0°
      *j
      0° to 0°15'
      *k
      0°15' to 0°30'
      *l
      0°30' to 0°45'
      *m
      0°45' to 1°00'
      *n
      1°00' to 1°15'
      *o
      1°15' to 1°30'
      *p
      Selected Bolt Combination
      The body and suspension may be damaged if the camber is not correctly adjusted in accordance with the above table.

      NOTICE:
      Replace the nut with a new one when replacing the bolt.

  1. Repeat the steps mentioned above. At step (A), replace 1 or 2 selected bolts.

    HINT:
    Replace one bolt at a time when replacing 2 bolts.



5. INSPECT TOE-IN

NOTICE:
Inspect while the vehicle is unloaded.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  1. Release the parking brake and move the shift lever to the neutral.

  1. Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)



    C188968E08
  1. Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (Dimension B).
    Text in Illustration 
    *a
    Tread Center Mark
    *b
    Dimension B
    V100135
    Front of the Vehicle

  1. Slowly push the vehicle straight ahead to cause the front wheels to rotate 180° using the front tire valve as a reference point.

    NOTICE:
    Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from (Step A) again.



    C188969E07
  1. Measure the distance between the tread center marks on the front side of the wheels (Dimension A).
    Text in Illustration 
    *a
    Dimension A
    V100135
    Front of the Vehicle

    Toe-in (Unloaded Vehicle):
    B - A
    C + D
    1.5 +/- 2.0 mm (0.0591 +/- 0.0787 in.)
    0°09' +/- 0°13' (0.15° +/- 0.22°)

    HINT:
    Measure "B - A" only when "C + D" cannot be measured.

    If the toe-in is not within the specified value, adjust it at the rack ends.



6. ADJUST TOE-IN


    C106036
  1. Measure the thread lengths of the right and left rack ends.

    Standard:
    Difference in thread length of 1.5 mm (0.0591 in.) or less

  1. Remove the rack boot set clips.

  1. Loosen the tie rod end lock nuts.

  1. Adjust the rack ends if the difference in thread length between the right and left rack ends is not within the specified range.

    1. Extend the shorter rack end if the measured toe-in deviates toward the outer-side.

    2. Shorten the longer rack end if the measured toe-in deviates toward the inner-side.

  1. Turn the right and left rack ends by an equal amount to adjust the toe-in to the center value.

    HINT:
    Try to adjust the toe-in to the center of the specified range.

  1. Make sure that the lengths of the right and left rack ends are the same.

  1. Tighten the tie rod end lock nuts to the specified torque.

    Torque:
    75 N*m{ 760 kgf*cm , 55 ft.*lbf }

    NOTICE:
    Temporarily tighten the lock nut while holding the hexagonal part of the steering rack end so that the lock nut and the steering rack end do not turn together. Hold the flat of the tie rod end and tighten the lock nut.

  1. Place the boots on the seats.



    C106037E07
  1. Using pliers, install the clip as shown in the illustration.
    Text in Illustration 
    *a
    Upper Side
    *b
    Front Side
    *c
    180° (Clip Installation Range)

    NOTICE:
    1. Install the clip so that its claws are within the clip installation range.
    2. Make sure that the rack boots are not twisted.



7. INSPECT WHEEL TURNING ANGLE

NOTICE:
Inspect while the vehicle is unloaded.



    C132439E12
  1. Fully turn the steering wheel left and right, and measure the wheel turning angle.
    Text in Illustration 
    *a
    Inside
    *b
    Outside
    V100135
    Front of the Vehicle

    Wheel Turning Angle (Unloaded Vehicle):
    Inside Wheel
    Outside Wheel
    (Reference)
    41°22' +/- 2° (41.37° +/- 2°)
    35°45' (35.75°)

    If the right and left inside wheel angles are not within the specified range, check the right and left rack end lengths.