Home › Brake › PARKING BRAKE › PARKING BRAKE CABLE (for Hatchback Drum Type)

PARKING BRAKE CABLE (for Hatchback Drum Type) > INSTALLATION

for Preparation Click here



1. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY
  1. Install the No. 3 parking brake cable assembly onto the backing plate with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install cable clamp B onto the rear axle beam.

    NOTICE:
    Securely install the clamp.

    HINT:
    When reusing the parking brake cable assembly, replace cable clamp B with a new part.

  1. Tighten the 5 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Pass the parking brake cable through a new cable clamp A, and then install cable clamp A onto the stud bolt.

    NOTICE:
    Securely install the clamp.

  1. Connect the No. 3 parking brake cable assembly onto the parking brake equalizer.



2. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:
Use the same procedure for the RH side as for the LH side.



3. INSTALL FUEL TANK COVER VENT CASE SUB-ASSEMBLY
  1. Install the fuel tank cover vent case sub-assembly with the bolt and clip.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



4. INSTALL FRONT NO. 4 FLOOR HEAT INSULATOR
  1. Install the front No. 4 floor heat insulator with the 2 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



5. INSTALL REAR BRAKE SHOE KIT


    C190261E02
  1. Apply high temperature grease to the surface of the backing plate which is in contact with the shoe.
    Text in Illustration 
    *1
    High Temperature Grease



    C108972
  1. Using needle-nose pliers, install the parking brake cable onto the parking brake shoe lever.



    C108971E01
  1. Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down spring cup.

    SST
    09718-00011  



    C179336E03
  1. Apply high temperature grease to the adjusting bolt.
    Text in Illustration 
    *1
    High Temperature Grease



    F040013E06
  1. Install the parking brake shoe strut set as shown in the illustration.
    Text in Illustration 
    *1
    Backing Plate
    *2
    Parking Brake Shoe Strut Set



    C108969E01
  1. Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down spring cup.

    SST
    09718-00011  



    F042698
  1. Using needle-nose pliers, install the tension spring onto the front brake shoe and rear brake shoe.



    C108968E01
  1. Using SST, install the shoe return spring onto the front brake shoe.

    SST
    09921-00011  

    NOTICE:
    Do not damage the wheel cylinder boot.



6. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY


7. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



8. ADJUST PARKING BRAKE LEVER TRAVEL
  1. Remove the rear console box (Click here).



    C233136
  1. Remove the hole plug, and turn the adjuster to expand the shoe until the drum locks.
    Text in Illustration 
    V100135
    Expand



    C233134
  1. Hold the automatic adjust lever away from the adjuster, and contract the brake shoe by turning the adjust bolt using another screwdriver until the drum can rotate smoothly.
    Text in Illustration 
    V100135
    Contract

    Standard:
    12 notches

  1. Check that there is no brake drag against the shoe.



    C234723E02
  1. Turn the lock nut until the parking brake lever travel is corrected to within the specified range.
    Text in Illustration 
    *1
    Lock nut

    Parking brake lever travel at 200 N (20 kgf, 45 lbf):
    8 to 11 clicks

  1. Operate the parking brake lever 3 to 4 times, and check the parking brake lever travel.

  1. Install the rear console box (Click here).



9. INSTALL REAR CONSOLE BOX ASSEMBLY
(Click here)