Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR (for Sedan)

FRONT DOOR (for Sedan) > DISASSEMBLY


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the LH side.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


B349416
  1. Disengage the clip and the claw, and remove the front door lower frame bracket garnish.



4. REMOVE FRONT ARMREST BASE UPPER PANEL


B136158
  1. for Driver Side:

    1. Remove the screw.

    2. Disengage the 2 clips and the 7 claws.

    3. Disconnect the connector and remove the front armrest base upper panel.



    B141925
  1. for Front Passenger Side:

    1. Remove the screw.

    2. Disengage the 2 clips and the 7 claws.

    3. Disconnect the 2 connectors and remove the front armrest base upper panel.



5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B136159
  1. Remove the screw.



    B351468
  1. Remove the clip.

  1. Disengage the 8 clips.



    B136161
  1. Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly, and remove the front door trim board sub-assembly.



6. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


B348854E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 guides and remove the front door inside handle sub-assembly.
    Text in Illustration 
    *a
    Protective Tape



7. REMOVE FRONT DOOR GLASS WEATHERSTRIP INNER
  1. Remove the front door glass weatherstrip inner from the front door trim board sub-assembly.



8. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY


    B134972
  1. Disconnect the speaker connector.



    B134969
  1. Drill out the 3 rivet heads using a drill with a bit diameter of less than 4 mm (0.157 in.), and remove the front No. 1 speaker.

  1. Operate the drill around the rivet head circumference and cut out the flange.

    CAUTION:
    Be careful. The cut rivet is very hot.

    NOTICE:
    Do not drill the rivet at an angle as this will cause damage to the drill and drill hole. Line up the drill and rivet, and carefully drill the rivet head straight out.

  1. After drilling out the flange, continue drilling to push out the shards on the drill.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.



9. REMOVE OUTER REAR VIEW MIRROR


B348847
  1. Disconnect the connector.

  1. Remove the 3 nuts.

  1. Disengage the claw and remove the outer rear view mirror.



10. REMOVE FRONT DOOR BELT MOULDING


    B134873E03
  1. Apply protective tape to the door panel in the periphery of the front door belt moulding.
    Text in Illustration 
    *a
    Protective Tape



    B134874
  1. Using a moulding remover, disengage the 6 claws and remove the front door belt moulding.



11. REMOVE FRONT DOOR TRIM BRACKET


B136164
  1. Remove the 2 screws and the front door trim bracket.



12. REMOVE FRONT DOOR SERVICE HOLE COVER


B136163
  1. Disconnect the connectors and clamps, and remove the front door service hole cover.

    NOTICE:
    Remove any butyl tape remaining on the door side.



13. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
  1. for Driver Side:

    1. Temporarily install the power window regulator master switch assembly.

  1. for Front Passenger Side:

    1. Temporarily install the power window regulator switch assembly.



    B351469
  1. Move the front door glass sub-assembly until the 2 bolts can be seen through the service holes.

  1. Remove the 2 bolts.

    NOTICE:
    Do not drop or damage the front door glass sub-assembly when removing the bolts.



    B351470E01
  1. Remove the front door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the front door glass sub-assembly.

  1. for Driver Side:

    1. Remove the power window regulator master switch.

  1. for Front Passenger Side:

    1. Remove the power window regulator switch.



14. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY


B351471E01
  1. Disconnect the connector.

  1. Loosen the bolt A.

  1. Remove the 5 bolts and the front door window regulator sub-assembly.

    NOTICE:
    Do not drop or damage the front door window regulator sub-assembly when removing the bolts.

    HINT:
    Remove the front door window regulator sub-assembly through the service hole.



15. REMOVE FRONT DOOR GLASS RUN


B348856
  1. Remove the clip and the front door glass run.



16. REMOVE FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER


B348857
  1. Remove the bolt.

  1. Disengage the guide and remove the front door frame sub-assembly rear lower.

    NOTICE:
    Do not drop or damage the front door frame sub-assembly rear lower when removing the bolt.

    HINT:
    Remove the front door frame sub-assembly rear lower through the service hole.



17. REMOVE FRONT DOOR FRAME SUB-ASSEMBLY FRONT LOWER


B348858
  1. Remove the bolt.

  1. Disengage the guide and remove the front door frame sub-assembly front lower.

    NOTICE:
    Do not drop or damage the front door frame sub-assembly front lower when removing the bolts.

    HINT:
    Remove the front door frame sub-assembly front lower through the service hole.



18. REMOVE FRONT DOOR OUTSIDE HANDLE COVER


B136172E01
  1. Remove the hole plug.
    Text in Illustration 
    *1
    Hole Plug

  1. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.



19. REMOVE FRONT DOOR LOCK


B136169
  1. Using a T30 "TORX" socket wrench, loosen the 3 screws.

    NOTICE:
    Do not drop or damage the front door lock when removing the screws.

  1. Move the front door lock downward, separate the door lock open rod and remove the front door lock.

    HINT:
    Remove the front door lock through the service hole.



    B349516
  1. Disengage the 6 claws and open the cover.



    B121553
  1. Disconnect the front door lock remote control cable and the front door inside locking cable.

  1. Remove the door lock wire harness seal.



20. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY


B136173
  1. Remove the front door outside handle assembly in the direction indicated by the arrow as shown in the illustration.



21. REMOVE FRONT DOOR OUTSIDE HANDLE PAD REAR


B351472
  1. Disengage the 2 claws and remove the front door outside handle pad rear.



22. REMOVE FRONT DOOR OUTSIDE HANDLE PAD FRONT


B351473
  1. Disengage the 2 claws and remove the front door outside handle pad front.



23. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


B136177
  1. Using a T30 "TORX" socket wrench, loosen the screw.

  1. Remove the front door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.



24. REMOVE DOOR OUTSIDE HANDLE PROTECTOR


B136184
  1. Remove the door outside handle protector in the direction indicated by the arrow as shown in the illustration.



25. REMOVE FRONT DOOR CHECK ASSEMBLY


B136180
  1. Remove the 3 bolts and the front door check assembly.

    NOTICE:
    Do not drop or damage the front door check assembly when removing the bolts.

    HINT:
    Remove the front door check assembly through the service hole.



26. REMOVE FRONT DOOR WEATHERSTRIP


B348859E01
  1. Remove the clip.
    Text in Illustration 
    *a
    Double-sided Tape

  1. Disengage the 34 clips.

  1. Peel off the double-sided tape and remove the front door weatherstrip.

    NOTICE:
    Remove any double-sided tape remaining on the door side.



27. REMOVE FRONT DOOR STIFFENER CUSHION


    B136190
  1. Remove the bolt and the front door stiffener cushion.



28. REMOVE CUSHION


B136182
  1. Remove the 2 cushions.