Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR (for Hatchback)

FRONT DOOR (for Hatchback) > DISASSEMBLY


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the RH side.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Power Window)

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



3. REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    B345202E03
  1. Insert a clip remover with its shaft wrapped in protective tape between the window regulator handle plate and front door trim board sub-assembly.
    Text in Illustration 
    *a
    Protective Tape

  1. Turn the front door window regulator handle assembly with the clip remover inserted, as shown in the illustration.

  1. Remove the front door window regulator handle assembly and the clip.

  1. Remove the window regulator handle plate.



4. REMOVE FRONT ARMREST BASE UPPER PANEL (w/ Power Window)


    B284582
  1. Using a moulding remover, disengage the 9 claws and the 4 guides.

  1. Disconnect the connector and remove the front armrest base upper panel.



5. REMOVE FRONT ARMREST BASE UPPER PANEL (w/o Power Window)


    B284583
  1. Using a moulding remover, disengage the 6 claws and the 3 guides.

    1. Disconnect the connector.

      HINT:
      If the armrest base upper panel is equipped with door lock switch, disconnect the connector.



6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for 5 Door)


    B273456E02
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
    Text in Illustration 
    *a
    Protective Tape



    B271595
  1. Remove the 3 screws.



    B271596
  1. Disengage the 7 clips.



    B271597E01
  1. Disconnect the front door lock remote control cable assembly and the front door inside locking cable assembly, and remove the front door trim board sub-assembly.
    Text in Illustration 
    *1
    Front Door Lock Remote Control Cable Assembly
    *2
    Front Door Inside Locking Cable Assembly



7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for 3 Door)


    B273456E02
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
    Text in Illustration 
    *a
    Protective Tape



    B271595
  1. Remove the 3 screws.



    B284585
  1. Disengage the 8 clips.



    B271597E01
  1. Disconnect the front door lock remote control cable assembly and the front door inside locking cable assembly, and remove the front door trim board sub-assembly.
    Text in Illustration 
    *1
    Front Door Lock Remote Control Cable Assembly
    *2
    Front Door Inside Locking Cable Assembly



8. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    B271598
  1. Disengage the 4 guides and remove the front door inside handle sub-assembly.



9. REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP (for 5 Door)


    B271599
  1. Disengage the 7 claws and remove the front door glass inner weatherstrip as shown in the illustration.



10. REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP (for 3 Door)


    B284586
  1. Disengage the 8 claws and remove the front door glass inner weatherstrip as shown in the illustration.



11. REMOVE FRONT DOOR WINDOW FRAME FRONT MOULDING

HINT:
Use the same procedure as for the LH side .



12. REMOVE FRONT DOOR WINDOW FRAME UPPER MOULDING (for Driver Side)

HINT:
Use the same procedure as for the LH side



13. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

HINT:
Use the same procedure as for the LH side .



14. REMOVE FRONT DOOR WINDOW FRAME REAR MOULDING (for 3 Door)

HINT:
Use the same procedure as for the LH side .



15. REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

HINT:
Use the same procedure as for the LH side .



16. REMOVE DOOR SIDE AIRBAG SENSOR (w/ Curtain Shield Airbag)
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B282656
  1. Disconnect the connector from the door side airbag sensor.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.




    1. Push and hold the white housing lock, and slide the yellow outer connector locking sleeve.


      C195226E09


      Text in Illustration 
      *1
      Housing Lock
      *2
      Outer Connector Locking Sleeve
      *a
      Slide
      -
      -

    2. Push and hold the white housing lock again, and slide the yellow outer connector locking sleeve to disconnect the connector.



    B282657
  1. Remove the bolt and door side airbag sensor.

    NOTICE:
    Loosen the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.



17. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY


    E222073
  1. Disconnect the connector.



    E222074
  1. Drill out the 3 rivet heads using a drill with a bit diameter of less than 4 mm (0.16 in.), and remove the front No. 1 speaker assembly from the front door panel.

  1. Operate the drill around the rivet head circumference and cut out the flange.

    CAUTION:
    Be careful. The cut rivet is very hot.

    NOTICE:
    Do not drill the rivet at an angle as this will cause damage to the drill and drill hole. Line up the drill and rivet, and carefully drill the rivet head straight out.

  1. After drilling out the flange, continue drilling to push out the shards on the drill.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.



18. REMOVE FRONT DOOR SERVICE HOLE COVER (for 5 Door)


    B271600
  1. Remove the front door service hole cover.

    HINT:
    Remove any butyl tape remaining on the door side.



19. REMOVE FRONT DOOR SERVICE HOLE COVER (for 3 Door)


    B284587
  1. Remove the front door service hole cover.

    HINT:
    Remove any butyl tape remaining on the door side.



20. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    B271601
  1. Remove the front door service hole cover.

  1. w/ Power Window:

    1. Connect the power window regulator master switch assembly.

    2. Connect the cable to the negative (-) battery terminal.

    3. Move the front door glass sub-assembly so that the door glass bolts can be seen.

    4. Disconnect the cable from the negative (-) battery terminal.

    5. Disconnect the power window regulator master switch assembly.

  1. w/o Power Window:

    1. Install the front door window regulator handle assembly.

    2. Move the front door glass sub-assembly so that the door glass bolts can be seen.

    3. Remove the front door window regulator handle assembly.



    B271602
  1. Remove the 2 bolts.



    B271603E01
  1. Remove the front door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    After the bolts are removed, do not allow the front door glass sub-assembly to fall.



21. REMOVE FRONT DOOR GLASS NO. 1 CHANNEL (for TMC Made)


    B284647E02
  1. Using a screwdriver with its tip wrapped in protective tape, remove the front door glass No. 1 channel.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Do not damage the front door glass sub-assembly.



22. REMOVE FRONT DOOR GLASS NO. 1 CHANNEL FILLER (for TMC Made)
  1. Remove the front door glass No. 1 channel filler.



23. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/ Power Window)


    B271605E03
  1. Disconnect the connector.

  1. Loosen the temporary bolt.
    Text in Illustration 
    *a
    Temporary Bolt

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator sub-assembly may fall and cause damage.

  1. Remove the 5 bolts.

  1. Remove the temporary bolt and the front door window regulator sub-assembly.



24. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/o Power Window)


    B284589E03
  1. Loosen the temporary bolt.
    Text in Illustration 
    *a
    Temporary Bolt

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator sub-assembly may fall and cause damage.

  1. Remove the 4 bolts.

  1. Remove the temporary bolt and the front door window regulator sub-assembly.



25. REMOVE FRONT DOOR NO. 1 STIFFENER CUSHION (for 3 Door)


    B284636E02
  1. Remove the 2 bolts and the 2 collars.
    Text in Illustration 
    *a
    Double-sided Tape

  1. Peel off the double-sided tape and remove the front door No. 1 stiffener cushion.



26. REMOVE FRONT DOOR GLASS RUN


    B271607
  1. Remove the front door glass run.



27. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B271608
  1. Remove the bolt.

  1. Disengage the guide and remove the front door rear lower frame sub-assembly.



28. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
  1. Disconnect the upper part of rear door weatherstrip.



    B271609
  1. Remove the screw.

  1. Remove the 2 bolts and the front door front lower frame sub-assembly.



29. REMOVE FRONT DOOR FIX WINDOW GLASS


    B271611
  1. Remove the front door fix window glass in the direction indicated by the arrow as shown in the illustration.



30. REMOVE FRONT DOOR FIX WINDOW WEATHERSTRIP
  1. Remove the front door fix window weatherstrip from the front door fix window glass.



31. REMOVE FRONT DOOR OUTSIDE HANDLE COVER


    B271615E01
  1. Remove the hole plug.
    Text in Illustration 
    *1
    Hole Plug

  1. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with the lock cylinder.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



    B271703
  1. Disengage the claw and 2 guides, and remove the front door outside handle cover.



32. REMOVE FRONT DOOR LOCK ASSEMBLY (w/ Power Door Lock)


    B271626
  1. Disconnect the connector.

  1. Using a "TORX" socket wrench T30, remove the 3 screws.



    E221614E01
  1. Slide the front door lock assembly downward, and remove the front door lock from the front door lock open rod.
    Text in Illustration 
    *1
    Front Door Lock Open Rod
    V100135
    Slide Direction



    E221639
  1. Remove the door lock wire harness seal from the front door lock.



33. REMOVE FRONT DOOR LOCK ASSEMBLY (w/o Power Door Lock)


    E228974
  1. Using a "TORX" socket wrench T30, remove the 3 screws.



    E221614E01
  1. Slide the front door lock assembly downward, and remove the front door lock from the front door lock open rod.
    Text in Illustration 
    *1
    Front Door Lock Open Rod
    V100135
    Slide Direction



    E221639
  1. Remove the door lock wire harness seal from the front door lock.



34. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    B271617
  1. Remove the front door outside handle assembly in the direction indicated by the arrow as shown in the illustration.



35. REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD


    B271619
  1. Disengage the 3 claws and remove the front door outside handle front pad.



36. REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD


    B271620
  1. Disengage the 2 claws and remove the front door outside handle rear pad.



37. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    B271625
  1. Using a T30 "TORX" socket wrench, loosen the screw.



    B271621
  1. Disengage the grommet and 2 claws, and remove the front door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.



38. REMOVE FRONT DOOR LOCK OPEN ROD


    B268981E01
  1. Remove the front door lock open rod as indicated by the arrows in the order shown in the illustration.
    Text in Illustration 
    *1
    Snap



39. REMOVE FRONT DOOR CHECK ASSEMBLY


    B271610
  1. Remove the 3 bolts and the front door check assembly.



40. REMOVE FRONT DOOR WEATHERSTRIP (for 5 Door)


    B271613
  1. Using a clip remover, remove the clip.

  1. Using a clip remover, disengage the 29 clips and remove the front door weatherstrip.



41. REMOVE FRONT DOOR WEATHERSTRIP (for 3 Door)


    B284595
  1. Using a clip remover, disengage the clip.

  1. Using a clip remover, disengage the 32 clips and remove the front door weatherstrip.



42. REMOVE FRONT DOOR PANEL CUSHION


    B271614
  1. Remove the 2 front door panel cushions.



43. REMOVE NO. 1 BLACK OUT TAPE (for 5 Door)


    B272530
  1. Using an infrared light, heat the black out tape.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    CAUTION:
    Do not burn yourself on the hot body panel or with the infrared light.

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Lift the end portion with your fingernail and peel it parallel to the attachment surface.