Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR (for Sedan)

FRONT DOOR (for Sedan) > REASSEMBLY



1. INSTALL CUSHION


B136182
  1. Install the 2 cushions.



2. INSTALL FRONT DOOR STIFFENER CUSHION


B136190
  1. Install the front door stiffener cushion with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



3. INSTALL FRONT DOOR WEATHERSTRIP


B348859
  1. Engage the 34 clips and install the front door weatherstrip.
    Text in Illustration 
    *a
    Double-sided Tape

  1. Apply though pressure to the sections with double-sided tape.

  1. Install the clip.



4. INSTALL FRONT DOOR CHECK ASSEMBLY


B136180E01
  1. Apply MP grease to the sliding areas of the front door check assembly.
    Text in Illustration 
    *a
    Door Panel
    *b
    Body Panel

  1. Install the front door check assembly onto the door panel with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    NOTICE:
    1. Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.
    2. To prevent contamination by foreign matter, install immediately applying adhesive.

  1. Install the front door check assembly onto the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



5. INSTALL DOOR OUTSIDE HANDLE PROTECTOR


B136185
  1. Install the door outside handle protector in the direction indicated by the arrow as shown in the illustration.



6. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


B136178
  1. Install the front door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.

  1. Using a T30 "TORX" socket wrench, tighten the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



7. INSTALL FRONT DOOR OUTSIDE HANDLE PAD FRONT


B351473
  1. Engage the 2 claws and install the front door outside handle pad front.



8. INSTALL FRONT DOOR OUTSIDE HANDLE PAD REAR


B351472
  1. Engage the 2 claws and install the front door outside handle pad rear.



9. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY


B136174
  1. Install the front door outside handle assembly in the direction indicated by the arrow as shown in the illustration.



10. INSTALL FRONT DOOR LOCK

NOTICE:
  1. If reusing a front door lock that has been removed, replace the door lock wire harness seal in the connecting part with a new one.
  2. Make sure that no grease or dirt adheres to the door lock wire harness seal surface in the connecting part.

  1. Apply MP grease to the sliding and rotating areas of the front door lock.

  1. Connect the front door lock remote control cable and the front door inside locking cable.

  1. Engage the 6 claws and close the cover.



    B116845
  1. Insert the door lock open rod into the front door lock, then set it to the door panel.

    NOTICE:
    Make sure that the outside handle link is securely engaged with the door lock.

  1. Apply adhesive to the threads of the screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent.

  1. Using a T30 "TORX" socket wrench, install the front door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



11. INSTALL FRONT DOOR OUTSIDE HANDLE COVER


B136172E01
  1. Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.
    Text in Illustration 
    *1
    Hole Plug

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    HINT:
    Make sure that the door lock key cylinder rod is inserted.

  1. Install the hole plug.



12. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY FRONT LOWER


B348858
  1. Engage the guide and install the front door frame sub-assembly front lower with the bolt.

    Torque:
    6.2 N*m{ 63 kgf*cm , 54 in.*lbf }



13. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER


B348857
  1. Engage the guide and install the front door frame sub-assembly rear lower with the bolt.

    Torque:
    6.2 N*m{ 63 kgf*cm , 54 in.*lbf }



14. INSTALL FRONT DOOR GLASS RUN


B348856
  1. Install the front door glass run.

  1. Install the clip.



15. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding and rotating areas of the front door window regulator sub-assembly.

    NOTICE:
    Do not apply grease to the window regulator spring.



    B351471E01
  1. Temporarily install the bolt A onto the front door window regulator sub-assembly.

  1. Insert the front door window regulator sub-assembly into the door panel. Use bolt A to hang the front door window regulator sub-assembly on the door panel.

    NOTICE:
    Do not drop the front door window regulator sub-assembly as it may be damaged.

  1. Install the front door window regulator sub-assembly with the 5 bolts and tighten the bolt A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



16. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


B351480E01
  1. Insert the front door glass sub-assembly into the door panel along the front door glass run as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the front door glass sub-assembly.



    B351469
  1. Install the front door glass sub-assembly onto the front door window regulator sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



17. INSTALL FRONT DOOR SERVICE HOLE COVER


B136187E01
  1. Apply butyl tape to the door panel, then install a new front door service hole cover as shown in the illustration.

    Specification:
    Area
    Dimension
    A
    2.0 mm (0.079 in.) or more
    B
    6.0 mm (0.236 in.) or more

    HINT:
    1. When installing the front door service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the front door service hole cover.
    3. After attaching the front door service hole cover, check the quality of the seal.

  1. Connect the connectors and clamps.



18. INSTALL FRONT DOOR TRIM BRACKET


    B136164
  1. Install the front door trim bracket with the 2 screws.



19. INSTALL FRONT DOOR BELT MOULDING


    B134875
  1. Engage the 6 claws and install a new front door belt moulding.

  1. Remove the protective tape.



20. INSTALL OUTER REAR VIEW MIRROR
  1. Engage the claw and install the outer rear view mirror.

  1. Install the 3 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



21. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY


    B134970E01
  1. Using an air riveter or hand riveter, install the front No. 1 speaker with 3 new strike rivets.

    HINT:
    Install the new strike rivets in the order shown in the illustration.

    NOTICE:

    1. B130465
      Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

    2. B130466
      Confirm that the rivets are seated properly against the speaker.
    3. Do not tilt the riveter when installing the rivet onto the speaker.
    4. Do not leave any space between the rivet head and speaker.

    5. B130467
      Do not leave any space between the speaker and door. Firmly hold the 2 items together while installing the rivet.

  1. Connect the speaker connector.



22. INSTALL FRONT DOOR GLASS WEATHERSTRIP INNER
  1. Install the front door glass weatherstrip inner onto the front door trim board sub-assembly.



23. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


B348855
  1. Engage the 4 guides and install the front door inside handle sub-assembly.



24. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B136161
  1. Connect the front door lock remote control cable assembly and front door inside locking cable assembly.



    B351468
  1. Engage the 8 clips and install the front door trim board sub-assembly.

  1. Install the clip.



    B136159
  1. Install the screw.



25. INSTALL FRONT ARMREST BASE UPPER PANEL


  1. for Driver Side:

    1. Connect the connector.



    2. B136158
    3. Engage the 7 claws and 2 clips, and install the front armrest base upper panel.

    4. Install the screw.



  1. for Front Passenger Side:

    1. Connect the 2 connectors.



    2. B141925
    3. Engage the 7 claws and 2 clips, and install the front armrest base upper panel.

    4. Install the screw.



26. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


B349416
  1. Engage the claw and the clip, and install the front door lower frame bracket garnish.



27. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }