Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR (for Sedan)

REAR DOOR (for Sedan) > REASSEMBLY



1. INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
  1. Apply MP grease to the sliding areas of the rear door outside handle frame sub-assembly.



    B136227
  1. Install the rear door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.



2. INSTALL REAR DOOR OUTSIDE HANDLE PAD FRONT


    B351477
  1. Engage the 2 claws and install the rear door outside handle pad front.



    B136224
  1. Using a T30 "TORX" socket wrench, tighten the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



3. INSTALL REAR DOOR OUTSIDE HANDLE PAD REAR


    B351476
  1. Engage the 2 claws and install the rear door outside handle pad rear.



4. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY


    B136222
  1. Install the rear door outside handle assembly in the direction indicated by the arrow as shown in the illustration.



5. INSTALL REAR DOOR OUTSIDE HANDLE COVER


    B136220
  1. Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



6. INSTALL REAR DOOR LOCK

NOTICE:
  1. If reusing a rear door lock that has been removed, replace the door lock wire harness seal in the connecting part with a new one.
  2. Make sure that no grease or dirt adheres to the door lock wire harness seal surface in the connecting part.

  1. Apply MP grease to the sliding and rotating areas of the rear door lock.

  1. Connect the rear door lock remote control cable and rear door inside locking cable.

  1. Engage the 7 claws and close the 2 covers.

  1. Insert the rear door lock into the outside handle frame release plate, then set it onto the door panel.

  1. Make sure that the outside handle frame link is securely engaged with the rear door lock.

  1. Apply adhesive to the threads of the screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent.

  1. Using a T30 "TORX" socket wrench, install the rear door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



7. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding and rotating areas of the rear door window regulator sub-assembly.

    NOTICE:
    Do not apply grease to the window regulator spring.



    B136217E01
  1. Temporarily install the bolt A to the rear door window regulator sub-assembly.

  1. Insert the rear door window regulator sub-assembly into the door panel. Use bolt A to hang the rear door window regulator sub-assembly on the door panel.

    NOTICE:
    Do not drop the rear door window regulator sub-assembly as it may be damaged.

  1. Install the rear door window regulator sub-assembly with the 3 bolts, and tighten the bolt A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



8. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    B348867
  1. Install the rear door glass sub-assembly onto the rear door window regulator sub-assembly in the direction indicated by the arrow as shown in the illustration.



9. INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP


    B136219
  1. Install the rear door quarter window glass to the rear door quarter window weatherstrip.



    B136228
  1. Install the rear door quarter window weatherstrip in the direction indicated by the arrow as shown in the illustration.



10. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    B136214
  1. Install the rear door window division bar with the 2 bolts.

    Torque:
    6.2 N*m{ 63 kgf*cm , 54 in.*lbf }

  1. Install the screw.



11. INSTALL REAR DOOR GLASS RUN


B136213
  1. Install the rear door glass run.



12. INSTALL REAR DOOR BELT MOULDING


    B134882
  1. Engage the 5 claws and install a new rear door belt moulding.



    B134880E03
  1. Remove the protective tape.



13. INSTALL REAR DOOR WEATHERSTRIP


    B348866E01
  1. Engage the 31 clips and install the rear door weatherstrip.
    Text in Illustration 
    *a
    Double-sided Tape

  1. Apply though pressure to the sections with double-sided tape.

  1. Install the clip.



14. INSTALL REAR DOOR CHECK ASSEMBLY
  1. Apply MP grease to the sliding areas of the rear door check assembly.



    B136211E01
  1. Install the rear door check assembly onto the door panel with the 2 bolts.
    Text in Illustration 
    *a
    Door Panel
    *b
    Body Panel

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent.

    NOTICE:
    To prevent contamination by foreign matter, install immediately after applying adhesive.

  1. Install the rear door check assembly onto the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



15. INSTALL REAR DOOR SERVICE HOLE COVER


    B136230E01
  1. Apply butyl tape to the door panel and install a new rear door service hole cover as shown in the illustration.

    Specification:
    Area
    Dimension
    A
    2.0 mm (0.079 in.) or more
    B
    6.0 mm (0.236 in.) or more

    HINT:
    1. When installing the rear door service hole cover, pull the links and connectors out through the rear door service hole.
    2. There should be no wrinkles or folds after attaching the rear door service hole cover.
    3. After attaching the rear door service hole cover, check the quality of the seal.

  1. Connect the connectors and engage the clamps.



16. INSTALL REAR DOOR TRIM BRACKET


    B136209
  1. Install the rear door trim bracket with the 2 screws.



17. INSTALL REAR DOOR GLASS WEATHERSTRIP INNER
  1. Install the rear door glass weatherstrip inner onto the rear door trim board sub-assembly.



18. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    B348865
  1. Engage the 4 guides and install the rear door inside handle sub-assembly.



19. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B208701
  1. Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.



    B208700
  1. Engage the 7 clips and install the rear door trim board sub-assembly.



    B208699
  1. Install the screw.



20. INSTALL REAR DOOR ARMREST BASE UPPER PANEL
  1. Connect the connector.



    B208702
  1. Engage the 7 claws and 2 clips, and install the rear door armrest base upper panel.

  1. Install the screw.



21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }