CYLINDER HEAD (for Sedan) > INSPECTION |
| 1. INSPECT CYLINDER HEAD FOR WARPAGE |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the surface that is in contact with the cylinder block and the manifolds.
| Surface | Specified Condition |
| Cylinder block side | 0.05 mm (0.0020 in.) |
| Intake manifold side | 0.10 mm (0.0039 in.) |
| Exhaust manifold side | 0.10 mm (0.0039 in.) |
| 2. INSPECT CYLINDER HEAD FOR CRACKS |
![]() |
Using a dye penetrant, check the combustion chamber, intake ports, exhaust ports and cylinder block surface for cracks.
If cracked, replace the cylinder head.
| 3. INSPECT INTAKE VALVE |
![]() |
Check the overall valve length.
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Check the valve head margin thickness.
| 4. INSPECT EXHAUST VALVE |
Check the overall valve length.
Using a micrometer, measure the diameter of the valve stem.
Check the valve head margin thickness.
| 5. INSPECT VALVE SPRING |
![]() |
Using a vernier caliper, measure the free length of the valve spring.
![]() |
Using a steel square, measure the deviation of the valve spring.
![]() |
Using a spring tester, measure the tension of the valve spring at the specified installed length.
| 6. INSPECT VALVE GUIDE BUSH OIL CLEARANCE |
![]() |
Using a caliper gauge, measure the inside diameter of the guide bush.
Subtract the valve stem diameter measurement from the guide bush inside diameter measurement to calculate the oil clearance.
| Guide Bush | Specified Condition |
| Intake | 0.025 to 0.060 mm (0.0010 to 0.0024 in.) |
| Exhaust | 0.030 to 0.065 mm (0.0012 to 0.0026 in.) |
| Guide Bush | Specified Condition |
| Intake | 0.08 mm (0.0032 in.) |
| Exhaust | 0.10 mm (0.0039 in.) |
| 7. INSPECT INTAKE VALVE SEAT |
Apply a light coat of prussian blue to the valve face.
Lightly press the valve against the seat.
![]() |
Check the valve face and seat in accordance with the following procedure.
If blue appears 360° around the face, the valve is concentric. If not, replace the valve.
If blue appears 360° around the valve seat, the guide and face are concentric. If not, resurface the seat.
Check that the seat contact is in the middle of the valve face with the width between 1.0 to 1.4 mm (0.039 to 0.055 in.).
| 8. INSPECT VALVE LIFTER |
![]() |
Using a micrometer, measure the lifter diameter.
| 9. INSPECT VALVE LIFTER OIL CLEARANCE |
![]() |
Using a caliper gauge, measure the lifter bore diameter of the cylinder head.
Subtract the lifter diameter measurement from the lifter bore diameter measurement to calculate the oil clearance.
| 10. INSPECT CAMSHAFT |
![]() |
Inspect the camshaft for runout.
Place the camshaft on V-blocks.
Using a dial indicator, measure the circle runout at the center journal.
![]() |
Inspect the cam lobes.
Using a micrometer, measure the cam lobe height.
![]() |
Inspect the camshaft journals.
Using a micrometer, measure the journal diameter.
| Journal | Specified Condition |
| No. 1 journal | 34.449 to 34.465 mm (1.3563 to 1.3569 in.) |
| Other journals | 22.949 to 22.965 mm (0.9035 to 0.9041 in.) |
| 11. INSPECT NO. 2 CAMSHAFT |
Inspect the camshaft for runout.
Place the camshaft on V-blocks.
Using a dial indicator, measure the circle runout at the center journal.
Inspect the cam lobes.
Using a micrometer, measure the cam lobe height.
Inspect the camshaft journals.
Using a micrometer, measure the journal diameter.
| Journal | Specified Condition |
| No. 1 journal | 34.449 to 34.465 mm (1.3563 to 1.3569 in.) |
| Other journals | 22.949 to 22.965 mm (0.9035 to 0.9041 in.) |
| 12. INSPECT CAMSHAFT THRUST CLEARANCE |
Install the camshafts.
![]() |
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
| 13. INSPECT CAMSHAFT OIL CLEARANCE |
Clean the bearing caps and the camshaft journals.
Place the camshafts on the cylinder head.
![]() |
Lay a strip of Plastigage across each of the camshaft journals.
Install the bearing caps .
Remove the bearing caps.
![]() |
Measure the Plastigage at its widest point.