Terminal No. (Symbol)
| Wiring Color
| Terminal Description
| Condition
| Specified Condition
|
D130-1 (IG+) - D130-23 (GND)
| V - W-B
| Ignition power supply
| Ignition switch: ON
| 11 to 14 V
|
D130-2 (A/C) - D130-23 (GND)
| L - W-B
| A/C switch signal
| Ignition switch: ON
| Below 1 V → 11 to 14 V
|
Defroster: OFF
|
A/C switch: OFF → ON
|
Defroster mode detection switch signal
| Ignition switch: ON
| Below 1 V → 11 to 14 V
|
A/C switch: OFF
|
Defroster: OFF → ON
|
D130-3 (HEAT) - Body ground*1
| LG - Body ground
| MAX HOT switch detection signal
| Ignition switch: ON
| 11 to 14 V
|
No. 3 heater control knob: MAX HOT
|
D130-4 (TE) - D130-15 (SG- 1)
| GR - B
| Evaporator temperature sensor signal
| Ignition switch: ON
| 1.0 to 1.3 V
|
Temperature near evaporator: 15°C (59°F)
|
D130-5 (SG-2) - Body ground
| L - Body ground
| Ground for A/ C pressure sensor
| Always
| Below 1 Ω
|
D130-7 (PRE) - D130-23 (GND)
| GR - W-B
| A/C pressure sensor signal
| Refrigerant pressure: Normal
| 0.63 to 4.73 V
|
Refrigerant pressure: Abnormal (less than 176 kPa [1.8 kgf/cm2, 26 psi] or more than 3030 kPa [30.8 kgf/cm2, 439 psi])
| Below 0.63 V or 4.73 V or more
|
D130-8 (TX+) - D130-23 (GND)
| V - W-B
| CAN communication signal
| Ignition switch: ON
| Pulse generation (See waveform 1)
|
D130-9 (TX-) - D130-23 (GND)
| W - W-B
| CAN communication signal
| Ignition switch: ON
| Pulse generation (See waveform 2)
|
D130-11 (SOL+) - D130-23 (GND)
| P - W-B
| A/C compressor operation signal
| Engine idling
| Pulse generation (See waveform 3)
|
Blower switch: 1
|
A/C switch: ON
|
D130-13 (PTC1) - Body ground*1
| SB - Body ground
| No. 2 integration relay operation signal
| Engine idling
| 11 to 14 V → Below 1 V
|
No. 3 heater control knob: MAX HOT
|
Engine coolant temperature: Below 75°C (167°F)
|
Ambient temperature: Below 10°C (50°F)
|
Blower switch: 0 → 1
|
Waiting time: 10 seconds
|
D130-14 (HR) - Body ground
| R - Body ground
| Heater blower motor relay operation signal
| Ignition switch: ON
| 11 to 14 V → Below 1 V
|
Blower switch: 0 → 1
|
D130-15 (SG-1) - Body ground
| B - Body ground
| Ground for evaporator temperature sensor
| Always
| Below 1 Ω
|
D130-16 (LED) - Body ground
| P - Body ground
| A/C switch indicator signal
| Engine idling
| 11 to 14 V → Below 4 V
|
A/C switch: ON
|
Blower switch: 0 → 1
|
D130-17 (SBLW) - Body ground
| GR - Body ground
| Blower motor ON signal
| Ignition switch: ON
| 11 to 14 V → Below 1 V
|
Blower switch: 0 → 1
|
D130-19 (PTC2) - Body ground*1
| P - Body ground
| No. 2 integration relay operation signal
| Engine idling
| 11 to 14 V → Below 1 V
|
No. 3 heater control knob: MAX HOT
|
Engine coolant temperature: Below 70°C (158°F)
|
Ambient temperature: Below 10°C (50°F)
|
Blower switch: 0 → 1
|
Waiting time: 20 seconds
|
D130-20 (PTC3) - Body ground*1
| V - Body ground
| No. 2 integration relay operation signal
| Engine idling
| 11 to 14 V → Below 1 V
|
No. 3 heater control knob: MAX HOT
|
Engine coolant temperature: Below 65°C (149°F)
|
Ambient temperature: Below 10°C (50°F)
|
Blower switch: 0 → 1
|
Waiting time: 30 seconds
|
D130-21 (HLS) - Body ground*1
| R - Body ground*2 G - Body ground*3
| Headlight signal
| Engine idling
| 11 to 14 V → Below 1 V
|
Head light switch: OFF → ON
|
D130-23 (GND) - Body ground
| W-B - Body ground
| Ground for main power supply
| Always
| Below 1 Ω
|
D130-24 (S5-3) - D130-23 (GND)
| Y - W-B
| Power supply for pressure sensor
| Ignition switch: ON
| 4.75 to 5.25 V
|
Terminal No. (Symbol)
| Wiring Color
| Terminal Description
| Condition
| Specified Condition
|
D130-1 (IG+) - D130-23 (GND)*1
| V - W-B
| Ignition power supply
| Ignition switch: ON
| 11 to 14 V
|
D130-3 (HEAT) - Body ground*1
| LG - Body ground
| MAX HOT switch detection signal
| Ignition switch: ON
| 11 to 14 V
|
No. 3 heater control knob: MAX HOT
|
D130-8 (TX+) - D130-23 (GND)*1
| V - W-B
| CAN communication signal
| Ignition switch: ON
| Pulse generation (See waveform 1)
|
D130-9 (TX-) - D130-23 (GND)*1
| W - W-B
| CAN communication signal
| Ignition switch: ON
| Pulse generation (See waveform 2)
|
D130-13 (PTC1) - Body ground*1
| SB - Body ground
| No. 2 integration relay operation signal
| Engine idling
| 11 to 14 V → Below 1 V
|
No. 3 heater control knob: MAX HOT
|
Engine coolant temperature: Below 75°C (167°F)
|
Ambient temperature: Below 10°C (50°F)
|
Blower switch: 0 → 1
|
Waiting time: 10 seconds
|
D130-14 (HR) - Body ground
| R - Body ground
| Heater blower motor relay operation signal
| Ignition switch: ON
| 11 to 14 V → Below 1 V
|
Blower switch: 0 → 1
|
D130-17 (SBLW) - Body ground
| GR - Body ground
| Blower motor ON signal
| Ignition switch: ON
| 11 to 14 V → Below 1 V
|
Blower switch: 0 → 1
|
D130-19 (PTC2) - Body ground*1
| P - Body ground
| No. 2 integration relay operation signal
| Engine idling
| 11 to 14 V → Below 1 V
|
No. 3 heater control knob: MAX HOT
|
Engine coolant temperature: Below 70°C (158°F)
|
Ambient temperature: Below 10°C (50°F)
|
Blower switch: 0 → 1
|
Waiting time: 20 seconds
|
D130-20 (PTC3) - Body ground*1
| V - Body ground
| No. 2 integration relay operation signal
| Engine idling
| 11 to 14 V → Below 1 V
|
No. 3 heater control knob: MAX HOT
|
Engine coolant temperature: Below 65°C (149°F)
|
Ambient temperature: Below 10°C (50°F)
|
Blower switch: 0 → 1
|
Waiting time: 30 seconds
|
D130-21 (HLS) - Body ground*1
| R - Body ground*2 G - Body ground*3
| Headlight signal
| Engine idling
| 11 to 14 V → Below 1 V
|
Head light switch: OFF → ON
|
D130-23 (GND) - Body ground*1
| W-B - Body ground
| Ground for main power supply
| Always
| Below 1 Ω
|