DTC B1423/23 Pressure Sensor Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1423/23 | Open or short in pressure sensor circuit |
|

| 1.CHECK REFRIGERANT |
Check the sight glass of the cooler unit refrigerant liquid pipe.
Prepare the vehicle in accordance with the chart below.
| Item | Condition |
| Vehicle Doors | Fully open |
| Temperature Setting | MAX COLD |
| Blower Speed | HI |
| A/C Switch | ON |
Compare the sight glass to the following chart.
| Item | Symptom | Amount of Refrigerant | Corrective Procedures |
| 1 | Bubbles visible | Insufficient* | (1) Check for gas leakage and repair if necessary (2) Add refrigerant until bubbles disappear |
| 2 | No bubbles visible | Empty, insufficient or too much | Refer to items 3 and 4 |
| 3 | No temperature difference between compressor inlet and outlet | Empty or nearly empty | (1) Check for gas leakage with gas leak detector and repair if necessary (2) Add refrigerant until bubbles disappear |
| 4 | Considerable temperature difference between compressor inlet and outlet | Correct or too much | Refer to items 5 and 6 |
| 5 | Immediately after A/C turned OFF, refrigerant becomes clear | Too much | (1) Drain or discharge refrigerant (2) Bleed air and supply proper amount of purified refrigerant |
| 6 | Immediately after A/C turned OFF, refrigerant foams and then becomes clear | Correct | - |
|
| ||||
| OK | |
| 2.READ VALUE USING TECHSTREAM (REGULATOR PRESSURE SENSOR) |
Warm up the engine.
Turn the ignition switch to OFF.
Connect the Techstream to the DLC3.
Turn the ignition switch ON and turn the Techstream main switch ON.
Turn the ignition switch to ON.
Turn the tester on.
Select the following menus: Body Electrical / Air Conditioner / Data List /
According to the display on tester, read the "Data List".
| Tester Display | Measure Item/Range | Normal Condition | Diagnostic Note |
| Regulator Pressure Sensor | Regulator Pressure Sensor / Min.: 0 kgf / cm 2G, Max.: 38.25 kgf / cm 2G | Actual regulator pressure is displayed | - |
| Result | Proceed to |
| NG | A |
| OK (When troubleshooting according to PROBLEM SYMPTOMS TABLE) | B |
| OK (When troubleshooting according to the DTC) | C |
|
| ||||
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER) |
![]() |
Disconnect the A3 air conditioning pressure sensor connector.
Disconnect the E8 air conditioning amplifier connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| A3-1 (-) - E8-11 (SG-1) | Below 1 Ω |
| A3-2 (PR) - E8-6 (PRE) | Below 1 Ω |
| A3-3 (+) - E8-1 (S5-3) | Below 1 Ω |
| A3-1 (-) - Body ground | 10 kΩ or higher |
| A3-2 (PR) - Body ground | 10 kΩ or higher |
| A3-3 (+) - Body ground | 10 kΩ or higher |
Reconnect the air conditioning pressure sensor connector.
Reconnect the air conditioning amplifier connector.
|
| ||||
| OK | |
| 4.INSPECT AIR CONDITIONING AMPLIFIER |
![]() |
Remove the air conditioning amplifier with its connectors still connected.
Measure the resistance.
| Tester Connection | Specified Condition |
| E8-11 (SG-1) - E8-12 (GND) | Below 1 Ω |
Turn the ignition switch ON.
Measure the voltage.
| Tester Connection | Specified Condition |
| E8-1 (S5-3) - E8-11 (SG-1) | 4.5 to 5.5 V |
Reinstall the air conditioning amplifier.
|
| ||||
| OK | |
| 5.INSPECT AIR CONDITIONING PRESSURE SENSOR |
![]() |
Remove the air conditioning amplifier with its connectors still connected.
Set the manifold gauge.
Warm up the engine.
Turn the A/C switch ON.
Measure the voltage.
| Tester Connection | Refrigerant Pressure | Specified Condition |
| E8-6 (PRE) - E8-11 (SG-1) | 196 to 3140 kPa (2.0 to 32.0 kgf/cm2, 28 to 455 psi) | 0.76 to 4.74 V |
Reinstall the air conditioning amplifier.
|
| ||||
| OK | ||
| ||