Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM (for Sedan)

METER / GAUGE SYSTEM (for Sedan) > TERMINALS OF ECU



COMBINATION METER ASSEMBLY

E126885E05

  1. Disconnect the D1 combination meter assembly connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D1-1 (IG2) - Body ground
    B - Body ground
    Ignition switch signal
    Ignition switch OFF → ON
    Below 1 V → 11 to 14 V
    D1-2 (ECU-B) - Body ground
    L - Body ground
    Battery
    Always
    11 to 14 V
    D1-24 (ET) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Disconnect the D76 combination meter assembly connector.



  4. Measure the voltage of the wire harness side connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D1-3 (FUEL) - Body ground
    V - Body ground
    Fuel level signal
    Ignition switch ON
    11 to 14 V
    D1-7 (ILL-) - Body ground
    GR - Body ground
    Light control rheostat signal
    Ignition switch OFF → ON
    Pulse generation
    (See waveform 1)
    D1-14 (ILL+) - Body ground
    G - Body ground
    Illumination signal
    Light control switch OFF → ON
    Below 1 V → 11 to 14 V
    D1-15 (TC) - Body ground
    Y - Body ground
    Tail cancel switch signal
    Tail cancel switch OFF → ON
    Below 1 V → 11 to 14 V
    D1-16 (+S) - Body ground
    SB - Body ground
    Vehicle speed signal (Output)
    Driving at approx. 20 km/h (12 mph)
    Pulse generation
    (See waveform 2)
    D1-17 (SI) - Body ground
    P - Body ground
    Vehicle Speed signal (Input)
    Driving at approx. 20 km/h (12 mph)
    Pulse generation
    (See waveform 2)
    D1-20 (CANH) - Body ground
    G - Body ground
    CAN communication line
    Ignition switch ON
    Pulse generation
    D1-21 (CANL) - Body ground
    W - Body ground
    CAN communication line
    Ignition switch ON
    Pulse generation
    D76-1 (CHG) - Body ground
    L - Body ground
    Charge warning light signal
    Ignition switch ON
    Engine start
    Charge warning light
    OFF → ON
    11 to 14 V → Below 1 V
    D76-2 (SW) - Body ground
    V - Body ground
    Brake fluid level warning light signal
    Ignition switch ON
    Brake fluid level warning light
    ON → OFF
    Below 1 V → 11 to 14 V
    D76-4 (EFI) - Body ground
    B - Body ground
    MIL signal
    Ignition switch ON
    MIL ON → OFF
    Below 1 V → 11 to 14 V
    D76-7 (FOG) - Body ground
    R - Body ground
    Front fog signal
    Ignition switch ON
    Front fog light switch
    OFF → ON
    Below 1 V → 11 to 14 V
    D76-8 (TURN L) - Body ground
    LG - Body ground
    Turn signal LH signal
    Ignition switch ON
    Turn signal LH indicator light
    OFF → ON → OFF
    Below 1 V → 11 to 14 V → Below 1 V
    D76-9 (PBLT) - Body ground
    BE - Body ground
    Seat belt warning light signal (Passenger side)
    Ignition switch ON
    Front passenger seat belt warning light OFF → ON → OFF
    Below 1 V → 11 to 14 V → Below 1 V
    D76-11 (BEAM-) - Body ground
    P - Body ground
    HI-BEAM indicator signal (-)
    Headlight dimmer switch (Hi-BEAM) Hi → Lo
    Below 1 V → 11 to 14 V
    D76-12 (S) - Body ground
    Y - Body ground
    Oil pressure signal
    OIL / P warning light ON → OFF
    Below 1 V → 11 to 14 V
    D76-14 (BEAM+) - Body ground
    GR - Body ground
    HI-BEAM indicator signal (+)
    BEAM indicator light OFF → ON
    Below 1 V → 11 to 14 V
    D76-15 (TURN R) - Body ground
    BR - Body ground
    Turn signal RH signal
    Turn signal RH indicator light OFF → ON → OFF
    Below 1 V → 11 to 14 V → Below 1 V
    D76-16 (IND) - Body ground
    G - Body ground
    Taillight indicator signal
    Light control switch OFF → ON
    Below 1 V → 11 to 14 V
    D76-17 (ODO) - Body ground
    L - Body ground
    ODO/TRIP switch signal
    Ignition switch ON
    5 V
    D76-18 (CLK) - Body ground
    R - Body ground
    Clock switch signal
    Ignition switch ACC
    5 V
    D76-19 (E1) - Body ground
    GR - Body ground
    Ground
    Ignition switch ON
    Below 1 V
    If the result is not as specified, the combination meter assembly may be malfunctioning.



      A005138E12
    1. Waveform 1: Using an oscilloscope
      Terminal Connections
      D1-7 (ILL-) - Body Ground
      Tool Setting
      5 V/DIV., 50 ms./DIV.
      Condition
      Ignition switch ON



    2. E115032E02
    3. Waveform 2: Using an oscilloscope
      Terminal Connections
      D1-16 (+S) - Body Ground
      D1-17 (SI) - Body Ground
      Tool Setting
      5 V/DIV., 20 ms./DIV.
      Condition
      Driving at approximately 12 mph (20 km/h)

      HINT:
      As the vehicle speed increases, the cycle of the signal waveform narrows.


MAIN BODY ECU

E114510E59


Text in Illustration 
*1
Rear view of Main Body ECU
-
-

B108641E52


Text in Illustration 
*1
Front view of Main Body ECU
-
-
  1. Disconnect the 4A, 4D and 4E main body ECU connectors.

  2. Measure the resistance of the wire harness side connectors.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    4A-5 (RRCY) - Body ground
    G - Body ground
    Rear door courtesy switch signal (LH and RH)
    Rear door (LH and RH) CLOSED → OPEN
    10 kΩ or higher → Below 1 Ω
    4A-7 (LGCY) - Body ground
    SB - Body ground
    Luggage door courtesy switch signal
    Luggage door CLOSED → OPEN
    10 kΩ or higher → Below 1 Ω
    4A-21 (DCTY) - Body ground
    R - Body ground
    Front door courtesy switch signal (Driver Side)
    Front door (Driver Side) CLOSED → OPEN
    10 kΩ or higher → Below 1 Ω
    4A-24 (PCTY) - Body ground
    L - Body ground
    Front door courtesy switch signal (Passenger Side)
    Front door (Passenger Side) CLOSED → OPEN
    10 kΩ or higher → Below 1 Ω
    4D-7 (KSW) - Body ground
    Y - Body ground
    Key unlock warning switch signal
    Key inserted → removed
    10 kΩ or higher → Below 1 Ω
    4E-17 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the main body ECU connectors.

  4. Measure the voltage of the wire harness side connectors.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    4C-2 (PKB) - Body ground
    Y - Body ground
    Parking brake signal
    Parking brake warning light ON → OFF
    Below 1 V → 11 to 14 V
    D33-22 (CANL) - Body ground
    W - Body ground
    CAN communication line
    Ignition switch ON
    Pulse generation
    D33-23 (CANH) - Body ground
    R - Body ground
    CAN communication line
    Ignition switch ON
    Pulse generation
    If the result is not as specified, there may be a malfunction in the wire harness.


COMBINATION METER INTERNAL CIRCUIT

E266450E02


E279555E03


E266452E02


Connectors 
Terminal No.
Wire Harness Side
D1
1
Ignition switch
2
Battery
3
Fuel sender gauge assembly
7
Light control rheostat
14
Taillight relay
15
Light control rheostat
16
Other ECU
17
Speedometer sensor
20
CAN communication line
21
CAN communication line
24
Body ground
D76
1
Generator
2
Brake fluid level warning switch
4
ECM
7
Fog light relay
8
Turn signal flasher relay
9
Hazard warning signal switch assembly
11
Headlight dimmer switch
12
Engine oil pressure switch
14
Headlight dimmer switch
15
Turn signal flasher relay
16
Taillight relay
17
Hazard warning signal switch assembly
18
Hazard warning signal switch assembly
19
Hazard warning signal switch assembly