Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM (for Sedan)

METER / GAUGE SYSTEM (for Sedan) > Speedometer Malfunction


DESCRIPTION


  1. The combination meter assembly controls the speedometer in accordance with vehicle speed signals from the speedometer sensor.

WIRING DIAGRAM


E118625E02


INSPECTION PROCEDURE

HINT:
If DTC U0129 has been stored, troubleshoot the CAN communication system first.

1.PERFORM ACTIVE TEST USING TECHSTREAM (SPEED METER)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus : Body Electrical / Combination Meter / Active Test.

    Body Electrical / Combination Meter / Active Test::

    Tester Display
    Test Part
    Control Range
    Speed Meter Operation
    0 / 40 / 80 / 120 mph
    0 / 40 / 80 / 120 / 160 / 200 km/h
    Acceptable range (km/h or mph): [Control range → Speedometer display]
    for mph
    1. 40 mph → 38.5 to 42 mph
    2. 80 mph → 79.5 to 84 mph
    3. 120 mph → 121 to 126.5 mph
    for km/h
    1. 40 km/h → 38 to 42 km/h
    2. 80 km/h → 78 to 84 km/h
    3. 120 km/h → 119 to 125 km/h
    4. 160 km/h → 159 to 167 km/h
    5. 200 km/h → 199 to 209 km/h

    OK:
    Vehicle speed displayed on the tester is approximately the same as that of the speedometer reading.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


2.READ VALUE USING TECHSTREAM (SPEED METER)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and the tester ON.

  1. Select the item below from the Data List, and read the value displayed on the Techstream.

    Body Electrical / Combination Meter / Data List::

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed / Min.: 0 km/h (0mph), Max.: 255 km/h(158mph)
    Almost same as vehicle speed
    (When vehicle is driving)
    -

    OK:
    Vehicle speed displayed on the tester is approximately the same as the actual vehicle speed.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.INSPECT SPEEDOMETER SENSOR
E118604E01
  1. Remove the speedometer sensor.

  1. Connect the positive (+) lead from the battery to terminal 1 and the negative(-) lead to terminal 2.

  1. Connect the positive (+) lead from the tester to terminal 3 and the negative (-) lead to terminal 2.

  1. Rotate the shaft.

  1. Check that the voltage output between terminals 2 and 3 varies between 0V and 11V.

  1. Reinstall the speedometer sensor.



NG
REPLACE SPEEDOMETER SENSOR (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY)


    E117013E02
  1. Disconnect the D1 combination meter assembly connector.

  1. Disconnect the C21 speedometer sensor connector.

  1. Measure the resistance

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-17 (SI) - C21-3 (SI)
    Always
    Below 1 Ω
    C21-2 (SE) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the combination meter assembly connector.

  1. Measure the voltage

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C21-1 (IG+) - Body ground
    Ignition switch ON
    11 to 14V

  1. Reconnect the combination meter assembly and speedometer sensor connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)