ENGINE (for Sedan) > ON-VEHICLE INSPECTION |
| 1. INSPECT ENGINE COOLANT |
Remove the water filler cap sub-assembly.
Check for excessive deposits of rust or scale around the water filler cap sub-assembly and radiator filler hole. The engine coolant should be free of oil.
If excessively dirty, replace the engine coolant.
Reinstall the water filler cap sub-assembly.
| 2. INSPECT ENGINE OIL |
Check the engine oil for deterioration, water intrusion, discoloration or thinning.
If the quality is visibly poor, replace the engine oil and oil filter.
| 3. INSPECT BATTERY |
Check the battery for damage and deformation. If severe damage, deformation or leakage is found, replace the battery.
Check the volume of electrolyte in each cell.
For batteries that are maintenance-free:
For batteries that are not maintenance-free:
| 4. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Remove the air cleaner filter element sub-assembly.
Visually check that there is no dirt, blockage, or damage to the air cleaner filter element.
| 5. INSPECT FAN AND GENERATOR V BELT |
![]() |
Check the belt for wear, cracks or other signs of damage.
If any of the following defects is found, replace the V-ribbed belt.
![]() |
Check that the belt fits properly in the ribbed grooves.
| *a | CORRECT |
| *b | INCORRECT |
![]() |
Inspect the V belt deflection and tension.
| *A | w/o Air Conditioner |
| *B | w/ Air Conditioner |
| Item | Specified Condition |
| New belt | 8.0 to 9.0 mm (0.31 to 0.35 in) |
| Used belt | 12.5 to 13.5 mm (0.49 to 0.53 in) |
| Item | Specified Condition |
| New belt | 700 to 800 N (71 to 82 kg, 157 to 180 lb) |
| Used belt | 300 to 400 N (31 to 41 kg, 67 to 90 lb) |
| 6. INSPECT SPARK PLUG |
![]() |
Check the electrode.
Using a megaohmmeter, measure the insulation resistance.
Alternative inspection method:
Quickly accelerate the engine to 4,000 rpm 5 times.
Remove the spark plug.
![]() |
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage to its thread and insulator.
If there is damage, replace the spark plug.
| Manufacturer | Product |
| DENSO | SK16R11 |
| NGK | IFR5A11 |
![]() |
Check the spark plug electrode gap.
![]() |
Clean the spark plug.
If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.
| 7. INSPECT IGNITION TIMING |
When using the Techstream:
Warm up and stop the engine.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Select the following menu items:
Powertrain / Engine and ECT / Data List / Active Test / Connect the TC and TE1 / ON.
Inspect the ignition timing during idling.
Turn the ignition switch off.
Disconnect the Techstream from the DLC3.
When not using the Techstream:
Remove cylinder head cover No. 2 .
Warm up and stop the engine.
![]() |
Connect the clip of the timing light to the wire harness, as shown in the illustration.
Turn the ignition switch to ON.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Inspect the ignition timing during idling.
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the ignition switch off.
Remove the timing light.
Install cylinder head cover No. 2 .
| 8. INSPECT ENGINE IDLING SPEED |
When using the Techstream:
Warm up and stop the engine.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Select the following menu items:
Powertrain / Engine and ECT / Data List / Engine Speed.
Inspect the engine idling speed.
Turn the ignition switch off.
Disconnect the Techstream from the DLC3.
When not using the Techstream.
Warm up and stop the engine.
![]() |
Install SST to terminal 9 (TAC) of the DLC3, then connect a tachometer.
Turn the ignition switch to ON.
Inspect the engine idling speed.
Turn the ignition switch off.
Disconnect the tachometer.
Remove SST from terminal 9 (TAC).
| 9. INSPECT COMPRESSION |
Warm up and stop the engine.
Remove cylinder head cover No. 2 .
Remove the 4 ignition coils .
Remove the 4 spark plugs.
Disconnect the 4 fuel injector connectors.
![]() |
Inspect the cylinder compression pressure.
Insert a compression gauge into the spark plug hole.
Fully open the throttle.
While cranking the engine, measure the compression pressure.
If the cylinder compression is low, pour a light coat of engine oil into the cylinder through the spark plug hole, then inspect it again.
Connect the 4 fuel injector connectors.
Install the 4 spark plugs.
Install the 4 ignition coils .
Install cylinder head cover No. 2 .
| 10. INSPECT CO/HC |
Start the engine.
Run the engine at 2,500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe while idling.
Check the CO/HC concentration during idling and when running at 2,500 rpm.
Check the air fuel ratio sensor operation (Click here).
Check the heated oxygen sensor operation (Click here).
See the table below for possible causes, then inspect the applicable parts and repair them if necessary.
| CO | HC | Problems | Possible Causes |
| Normal | High | Rough idling |
|
| Low | High | Rough idling (Fluctuating HC reading) |
|
| High | High | Rough idling (Black smoke from exhaust) |
|